Fantastic video. This gave me info on diagnostics mode and then one of the links gave me another site with all the error codes. I spent $200 having a tech come out but i do not think he ran the diagnostics. Had surmised it was the lid lock switch which I had him replace. Right now after a bad start, the washer seems to be working. At least now I have the knowledge to diagnose the problem.

Thanks, the lid lock was my problem, so I appreciate this and the link to the codes and the replacement how-to.

very helpful, thanks

I wasn't strong enough to pull the washer out to unplug it so I flipped the breaker and it fixed the problem. Thinking that a power surge that went out an hour beforehand caused the blinking lid lock.

Ty subscribed!!

Thanks Wayne, that’s what I’m talking about. No bullshit, just facts 🙏🏻

Thank u luckily I only had to unplug mine and wait a few minutes.

My lid lock light keeps flashing and won't stop flashing how do I get it to go into diagnostic mode I've got a maytag centennial top load MVWC2OOXW0 is the model number

Don’t fail too often: 343k viewers

@shelia95

3 жыл бұрын

I'm done! 😂😂

i change that and is the same problem

I got my actuator part fixed ..but now it leaks a little?but work fine.. hoses are tight ?

@searspartsdirect

7 жыл бұрын

Check the tub seal that seals the opening where the gear case shaft goes through the outer tub. Replace that seal if it leaks. You may need to have a service technician complete that repair. Here’s a link where you can schedule service: www.searshomeservices.com/.

My locked light was blinking and the machine wouldn't turn on, so I unplugged it for a minute and all is well.😊

@samanthaworld2587

3 жыл бұрын

I unplugged my for a day n it still won't start

Yes and I just inherited a Kenmore Top-Loading HE Low Water Washer Model 2130 with home purchase. The house works but the Kenmore 2130 does not. Lock light always flashing. It was purchased by previous owner in 2011. All references to troubleshoot refer to models 2012 and on (VMW). How do I troubleshoot this model? Very frustrated. Would appreciate some help please.

@searspartsdirect

8 жыл бұрын

Your washer model 2130 (full model number 110.2130) is almost exactly the same and uses the same troubleshooting as the Kenmore VMW washer in this video. Follow the steps shown in the video to recall the saved error codes as the first step in fixing the washer. Once you find out which error codes the washer recorded, you’ll likely be able to determine which components need repair or replacement. Post additional details (including the error codes displayed) if you need more help.

I have the same problem. My machine washes for a minute or two then it stops. The lid locked is not flashing.

I have this same washer and it made a grinding noise when spinning. Finally, today it made a really loud noise when it was agitating, like something got stuck and it quit and the lock lid light would flash. I can’t run a diagnostic test because the lid lock mode won’t turn off, what can I do?

@searspartsdirect

4 жыл бұрын

The grinding noise could have been caused by coins or debris stuck in the drain pump. If the washer can't drain the water, it will run the drain pump for 5 to 7 minutes. Unplug the washer for 1 minute and then plug it back in. If the lid lock flashes, then the control is likely trying to run the drain pump for the 5 to 7 minute interval. Wait for 7 minutes and see if the lid lock stops flashing. If it does, you can then enter the diagnostic test mode and look at error codes saved by the washer control. If the long drain time error code (F9E1) appears, then you'll likely need drain water out of the washer, unplug the washer and check the drain pump. Here's a video/guide that shows how to access (and replace) the drain pump: www.searspartsdirect.com/diy/repair-guide/how-to-replace-the-drain-pump-in-a-top-load-washer . The grinding noise could also be caused by a failed mode shifter. If the lid lock stops flashing after plugging the washer back in, then enter the diagnostic mode and check for saved error codes. If the mode shifter fault code (F7E5) appears, you'll need to unplug the washer then examine and possibly replace the mode shifter. Here's a video/guide that shows how to access the mode shifter: www.searspartsdirect.com/diy/error-codes/washer-repair/1234598/kenmore-110-model-vmw-top-load-washer/0582 . Here's a list of the error codes for the washer in case you see a different error code in diagnostics: www.searspartsdirect.com/diy/error-codes/washer-repair/1234598/kenmore-110-model-vmw-top-load-washer/0582 . We hope this information helps. If you need further assistance let us know (and include the model number of your washer so we know the exact type of VMW washer that you have).

My problem was stuck in sensing mode. Replaced actuator and didn't fix it. Turned out to be the board. These machine are a pain the ass to troubleshoot.

good day sir..i have same trouble of the video that you share..sir how can i repair that problem..the lid lock is contineusly blinking...can you tell to me sir...thankyou

@searspartsdirect

8 жыл бұрын

The flashing lid lock light indicates that the washer encountered a component problem and recorded an error code. Follow the steps in the video to recall the saved error codes from the washer’s memory. The error code will typically point you in the direction of the component failure. Here’s a link for a chart that shows the error codes for that washer: www.searspartsdirect.com/washer-repair/error-codes/kenmore-110-model-vmw-top-load-washer-error-codes.html If you need more help once you recall the error code(s) from the washer’s memory, post additional details and we’ll assist you further.

Hi I was getting error code F7 E1 and F7 E5 which leads to the shift actuator being replaced(I think). I ended up replacing the shift actuator. Everything was going well for like a week and now those error codes are back. Is there a way to reset the codes or is my new actuator faulty?

@searspartsdirect

8 жыл бұрын

It’s possible but highly unlikely that the new actuator is faulty. Try calibrating the washer as shown at 2:18 in this video: kzread.info/dash/bejne/imlmzMmYpNDYkdI.html. If that doesn’t help, rotate the spin basket to see if it spins smoothly-those codes can appear if the spin basket isn’t spinning smoothly. If the basket doesn’t spin smoothly, unplug the washer and remove the spin basket as shown in this video: kzread.info/dash/bejne/pYdhw8-NitLZppM.html. Check for an item stuck between the spin basket and outer tub and remove if you find one. If you don’t find anything stuck, then your washer may have a bad bearing in the bottom of the outer tub. You’ll likely have to replace the outer tub to fix that problem. If spin basket does rotate smoothly when you check it, then a wiring connection could be loose. Unplug the washer and check the wiring on the shift actuator and the electronic control board. Reconnect any loose wires. If the wires are okay, then the washer could have a defective shift actuator, a bad electronic control board or a damaged wire harness.

kenmore topload washer 110.5072012 is stuck on sensing light and wont do anything else how can i fix this?

@searspartsdirect

7 жыл бұрын

The washer won’t go into the diagnostic test mode with the sensing light on. Press and hold the Start/Pause button for 3 seconds to turn off the Sensing light and then enter the diagnostic test mode to display the error codes. If you’re not able to turn off the sensing light, then the electronic control board (part W10632925 -- www.searspartsdirect.com/part-number/W10632925/0026/110.html ) may have failed. Here’s a video that shows how to replace that control board: kzread.info/dash/bejne/imlmzMmYpNDYkdI.html

I just got my Maytag already having issues

I unpugged my washer for a couple of minutes and the lid lock light went out and everything is working fine now

@shine10000000

4 жыл бұрын

Thanks! Me too!

My washer won’t reset and it keeps locking and unlocking. Any help is appreciated.

My lid lock is on...not flashing...I have the same model in this video. The washer stops on rinse/spin but has a full tank of water.How do I drain the water out and do I need to purchase a motor?! Does Sears sell this washer knowing it will fail????

@searspartsdirect

8 жыл бұрын

Even though the lid lock light isn’t flashing, the washer likely encountered a component failure and saved a fault code. Follow the steps in the video to recall the saved fault code. That fault code will likely point you in the direction of your failure. If you need more help after finding the fault code, post additional details including the fault code that the washer displayed. You’ll probably need to bail the water out of the washer using a container. You can also use a wet/dry shop vac to remove the water. Overall, this model of Kenmore washer is fairly dependable. That being said, appliance failures can happen at any time. Hopefully, the lid lock video will help you find the problem and fix it.

@danmcdonald1163

6 жыл бұрын

Rofiesha Watts

I having that problem I change that part and still the same problem help plz

Hi my lid lock light dont turn on ,but the washer gets water and starts washing and drains but then it doesn't get water to rinse and the wash light starts to blink and you here a noise like when lid lock ,any help thanks

@jonellmagicbroompitts2926

4 жыл бұрын

Carlos Silva my same problem right now. Have any luck.?

This guy is hilarious

My whirlpool washer lid lock light flashes when entered into the reins cycle. Any suggestions as to the cause of the problem?

@searspartsdirect

3 жыл бұрын

Use the steps in this video to determine the fault code being recorded when the failure occurs at the beginning of the rinse cycle. Here's the page that shows troubleshooting for the error codes on a Whirlpool VMW washer: www.searspartsdirect.com/diy/error-codes/washer-repair/1234598/whirlpool-cabrio-top-load-washer/1198 . Follow the troubleshooting steps for the code that's occurring.

My lid lock keeps going out within 3 months of time. What could be the problem ?

Hi, on my washer the SENSING light is on, and cant do anything else, tried the diagnostic mode, but No luck. Can u help me, tks. Joe O.

@searspartsdirect

4 жыл бұрын

Try unplugging the washer for 3 minutes and then plugging it back in. That may reset the electronic control board so the washer works normally. If the washer remains completely dead with the sensing light on when you plug it back in, let the washer stay on for about 7 minutes. There may be an item or debris stuck in the drain pump and the control will try to run the drain pump for 7 minutes then stop. The lid lock will likely blink after 7 minutes. You may then be able to enter the diagnostic test mode to see saved error codes. If something is stuck in the pump, you'll need to unplug the washer and clear or replace the drain pump. Here's a video that shows how to access the drain pump: www.searspartsdirect.com/diy/repair-guide/how-to-replace-the-drain-pump-in-a-top-load-washer. If you clear or replace the drain pump, the washer may work normally unless saved error codes indicate that the washer has a different failure. We hope this information helps. If you need further assistance, let us know.

I have the same washer. The problem we have right now is that the washer seems to be "off" meaning none of the lights are lit or blinking. No response when the power button is depressed. And the washer seems to be in the drain water mode. You can hear the suctioning, but the washer isn't doing anything else. Also, the lid is not locked. All lights are off. Any ideas?

@searspartsdirect

7 жыл бұрын

The washer likely encountered a problem draining the water, so it’s continuously running the drain pump. Try this-unplug the washer for 30 seconds and then plug it back in. You should hear the drain pump running again after restoring power. Let the drain pump run for 5 to 7 minutes until it stops. Once the drain pump stops, you should be able to enter the diagnostic test mode and see the fault code recorded. You’ll likely see the F9- E1 code indicating the control detected a long drain time. You’ll probably need to check the drain pump for a clog. Here’s a video that shows how to access and replace the drain pump: kzread.info/dash/bejne/iqKGlpSxera_XZM.html.

@phwlee

7 жыл бұрын

Thanks. I did let it run and it did shut off after about 7 minutes or so. I got the owners manual out from the inside corner and did a diagnostic on it and a re-calibrate. It's running good now. I will check the pump for a clog. Thanks

@DanWebster

10 ай бұрын

remove the drain pump and inspect for a sock or stocking.

How do I find a the Error Code? The fill light on mine keeps blinking.

@searspartsdirect

7 жыл бұрын

Unplug the washer for 3 minutes to reset the control board. Plug the washer back in and then enter the diagnostic test mode to recall the error codes as shown in the video. If you’re not able to start the diagnostic test mode after resetting the control board, reply to this thread with the model number of your washer and additional details for more help with this problem.

I have a whirlpool washer Model # WTW4800XQ4 and the Serial # is C25023149 and the lid Lock light is flashing constantly and I've tried to get it into Diagnostics mode and it just will not work no matter what. I had it in storage for 6 to 7 months while I was moving. I moved the washer inside and plugged it in. I ran a rinse and spin cycle to just clean it out and get the smell out. It stopped for the longest time during the cycle and I tried to stop it but it wouldn't and I had to just restart it again. After all was said and done I closed the lid and went to bed that night and when I woke up the next morning the Lid Lock Light was Flashing. Any suggestions on what I should try and fix this problem?? I am on disability and really do not have much money at all needless to say. Someone Please help me !! Oh , the washer was bought new and used for a total of 8 months and then it was put into storage until I just got all moved into my new place 3 months later and brought it into the house then. Thought I was going to get to do all of my laundry but that isn't happening right now at the moment. I'e got FAITH in someone out there in the web universe who can help me get my laundry finished. The whole bottom of inside the washer is full of Laundry Soap , LOL This is my reply to SEARS PARTS DIRECT : I did exactly what you told me to and it does nothing but the LID LOCK light just keeps flashing.Anything else that I should try? I just cannot seem to get this into diagnostics mode for some reason. My washer has a piece that goes into a slot when you close the lid. This is not the 2 magnet switch.

@searspartsdirect

4 жыл бұрын

Try this. Unplug the washer for 5 minutes to reset the electronic control board then plug the washer back in. Wait 10 seconds before trying to enter the diagnostic test mode. Rotate the control dial left a few clicks before entering the diagnostic test mode. Wait ½ second between clicks when turning the control dial right-right-right-left-right to enter the diagnostic test mode. We hope this advice helps. If you need further assistance, let us know.

I put my whirlpool washer on self clean I only added bleach then now the red light keeps blinking won't lock nothing

I don't see a link to the method of getting to the diagnostic codes. Help!

@searspartsdirect

5 жыл бұрын

Here's a link to the video/article for entering the diagnostic test mode and viewing diagnostic codes: www.searspartsdirect.com/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video.html . To view links attached to the video above, click the "i" in the top right hand corner of the video screen.

my problem is that when i try to retrieve the fault code all the lights blink i put it in diagnostics mode then go to complete press the start button and all the lights come on please help me

@searspartsdirect

7 жыл бұрын

Your details seem to indicate that you’re entering the diagnostic test mode and entering the error code display mode correctly as shown in this video: kzread.info/dash/bejne/iI6jpcyjl9jegqw.html Turn the dial one click clockwise to display the first saved error code as shown at 1:20 in the video.

I have the same washer and mine blinks on spin mode and won't finish the load. Any ideas???

@searspartsdirect

3 жыл бұрын

When the lock light flashes in the spin mode, the control likely detected a component failure and recorded an error code in its memory. Follow the steps in this article/video to display and decipher the error code: www.searspartsdirect.com/diy/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video

I have 3 whirlpool washer when switched on the lid lock light blinks intermittently and the machine stops for a very short time I have changed the lid lock , the actuator the control board but the problem persists

@searspartsdirect

7 жыл бұрын

In your situation, the lid lock may not be engaging the lid strike consistently. Many of the Whirlpool models have a plastic bezel surrounding the hole in the top panel that the lid strike pushes through when you close the lid. If that bezel isn’t aligned properly, the lid lock may not engage the strike, causing the lid lock to flash. Check that bezel and center it over the raised mounting surface on the washer top panel. You’ll hear a click when that bezel snaps into its proper position if it wasn’t aligned correctly. If the bezel is okay, then we recommend that you enter the diagnostic test mode and recall the saved error code as shown in this video: www.searspartsdirect.com/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video.html. The saved error codes should point you in the direction of the failure so you can fix the washer.

@samsoundflint6208

4 жыл бұрын

@@searspartsdirect So, what is the magic angle that would engage the strike? On my Bacon, pardon, Cabrio, it works on and off, sometimes works without any problems for weeks, sometimes refuses to work at all, and just as mysteriously decides to, then off again, etc. I've figured out that the strike itself is worn out (darn cheap plastikk part) and slightly bent, hence the said bezel is not the problem, but the strike itself slightly, very slightly misshapen. I just wish all the parts were made from replaceable metal and not crappy white plastikk that bends too easily. I also wish entire magical "lid lock assembly" would be engineered to last as long as the entire machine, and not just slightly longer than the warrantee period.

@searspartsdirect

4 жыл бұрын

@@samsoundflint6208 The lid strike should fit straight down into the lid lock/switch. Your details seem to indicate that the lid strike is damaged so it intermittently isn't tripping the lid switch. Replacing the lid strike should fix the problem. We understand your concerns about the design of the lid strike and we'll pass those concerns along to Whirlpool.

how do you get the codes/

@searspartsdirect

Жыл бұрын

Here's an article/video that shows how to get the codes: www.searspartsdirect.com/diy/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video

What if the "sensing" light keeps blinking?

@searspartsdirect

5 жыл бұрын

Unplug the washer for 1 minute to reset the electronic control board and then plug the outlet cord back in to restore power. The control may work properly after restoring power. If not, you can try running the calibration mode as shown in this video: www.searspartsdirect.com/article/how-to-calibrate-a-washer-after-a-repair-video.html . If the sensing light still flashes constantly and the washer won't start, run the diagnostic test mode and check for error codes. If you're not able to start the diagnostic test, then the electronic control board in the washer may have failed. We hope this information helps. If you need further assistance, let us know the model number of your washer and give us additional details about the failure.

How do I reset the error codes?

@searspartsdirect

6 жыл бұрын

When you're in the diagnostic test mode, turn the control knob until all status lights (Fill, Wash, Rinse, Spin and Done) are lit, then press and hold the Start button for 3 seconds to clear all error codes and exit the diagnostic test mode. In case you need it, here's the video that shows how to enter the diagnostic test mode: www.searspartsdirect.com/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video.html.

I tried everything the test did the lights then turned off didn’t do anything and mines still locked with my work clothes on it can anyone help?

@searspartsdirect

5 жыл бұрын

Unplug the washer for 1 minute and then plug it back in. This will reset the electronic control board. You may hear the pump running after you plug the washer back in. If so, wait 7 minutes and within that time, the drain pump should shot running, The washer may unlock the lid and operate normally. If not, you should be able to run the diagnostic test mode and find the cause of the washer failure. We hope this information helps. If you need further assistance, let us know (and give us the model number of your washer so we can provide specific troubleshooting for your model).

the washer just makes a clicking sound and then the lid lock light turns on but its not blinking

@searspartsdirect

6 жыл бұрын

Even though the lid lock light isn't blinking, the washer likely recorded an error code that can point you in the direction of the failure that's preventing the washer from running. Recall the recorded error codes as shown in this video: www.searspartsdirect.com/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video.html. Troubleshoot the error codes that you recall from the washer control’s memory.

Error lights won't come on

My lid locked blinks and blinks I can’t get it to run diagnostic

@searspartsdirect

5 жыл бұрын

Let us know the model number of your washer and we’ll try to provide some additional technical help and advice based on your specific model.

@michaelfreeman1182

5 жыл бұрын

That's_soMathis _

I've unplugged it for days and still not working.

@searspartsdirect

4 жыл бұрын

Enter the diagnostic test mode and view the saved error codes as shown in this video/article: www.searspartsdirect.com/diy/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video . If you're not able to enter the diagnostic test mode, the drain pump may be running as soon as you plug the washer in due to the control detecting a water overflow condition. You won't be able to enter the diagnostic test mode if the drain pump is running in that scenario. Plug the washer in and wait 7 minutes for the drain pump to quit running then try entering the diagnostic test mode to view saved error codes. Troubleshoot and fix the conditions that caused the error codes then you should be able to use the washer again. We hope this information helps. If you need more assistance, let us know the model number of your washer and give us additional details about the problem.

But what do the error codes MEAN?

@searspartsdirect

6 жыл бұрын

This video article shows how to decipher the error codes: www.searspartsdirect.com/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video.html.

Water is just pouring in the bottom left side of the washer

@searspartsdirect

4 жыл бұрын

Let us know the model number of your washer and additional details about the problem and we'll try to help you resolve this issue.

I guess I'm the dummy of the page here. I have gotten it to display the diagnostic lights, but I am clueless how to decipher them.

@searspartsdirect

7 жыл бұрын

Dex, this video article shows how to decipher the error codes: www.searspartsdirect.com/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video.html.

@DexKoontz

7 жыл бұрын

Thank you!

@roxannjones1208

6 жыл бұрын

This still makes No Sense to me. I clicked your link but I'm still not understanding how to read the codes. Can you put it in simple persons terms please. Thank you!

@fernandacastaneda8776

6 жыл бұрын

Roxann Jones did u figure it out?

@edgarmartinez7371

4 жыл бұрын

@@roxannjones1208 On vertical modular washers (VMWs), the first set of error codes start with F followed by a number (sensing enabled). The second set of error codes start with E followed by a number (no sensing). The numbers that follow will be: wash light is 8; rinse light is 4; spin light is 2; cycle complete light is 1

Panel lights won’t come on at all. Outlet has power.

@searspartsdirect

6 жыл бұрын

Unplug the washer and remove the back console panel. Check the power cord wire connections on the electronic control board. Reconnect any loose power cord wires. If the power cord wire connections are okay, you may need to replace the electronic control board.

@vincentbrown808

6 жыл бұрын

Sears PartsDirect Kenmore series 500. Stays in drain pump mode and will not do anything else ?

my lid lock light just don't come on at all not even in test mode. in test mode it works even the spin. in real mode it will do everything but spin. oh and it has zero codes

@searspartsdirect

5 жыл бұрын

Let us know the model number of your washer and we'll try to provide some troubleshooting tips to help you fix the problem.

@MadsWorld34

5 жыл бұрын

@@searspartsdirect thanks but i just went and bought a new one this morning.

Lights won’t come on at all. Power source is good.

Can't get any lights to light up in diagnostic mode. Occasionally can get sensing mode light to come on (not in diagnostic mode, though), but nothing happens. There is a very faint click but the lid never locks and no lights (other than sensing) come on. There is about an inch of water left in the tub, I took all of the clothes out. It looks like it did 1 round of rinsing and agitating and then it went out. Tried plugging and leaving unplugged. Tried diagnostic mode about a thousand times. If I leave it plugged in, it has a very low, quiet sound, almost like it's trying to drain. And occasionally there is a loud sound like....some kind of machine for just 1 second. Then nothing. It never comes back on. Please help.

@searspartsdirect

5 жыл бұрын

Unplug the washer for 2 minutes to reset the electronic control board and then plug the washer back in. Try to enter the diagnostic test mode a few more times after resetting the control board. Accessing the error codes is the best way to troubleshoot the washer. If you still can't start the diagnostic test mode, unplug the washer, remove any items from the tub (if not already removed) and use a wet/dry shop vacuum to drain any water remaining in the tub. Take off the back panel on the console ( www.searspartsdirect.com/repair-guide/washer/how-to-replace-the-electronic-control-board-on-a-top-load-washer.html ) and check all wiring connected to the electronic control board. Reconnect any loose wires. If all wires are connected to the electronic control board properly, reassemble the console and shut off the water supply faucets for the washer. Disconnect the water lines and lay down some cardboard to protect the washer cabinet from scratches then lay the washer down on its side. ( www.searspartsdirect.com/repair-guide/washer/how-to-replace-the-shifter-assembly-in-a-top-load-washer.html ) Check all wiring connections on bottom washer components (the drain pump, mode shifter and drive motor). Reconnect any loose wires. Reconnecting loose wires may fix the problem that you're having with the washer or reconnecting loose wires may enable the control to enter its diagnostic test mode to help you find the failed component that's preventing the washer from working. Set the washer upright and reassemble the washer. Restore the water supply and electrical power. Try to start a cycle. If the cycle doesn't start, try entering the diagnostic test mode. If the washer still won't start or enter the diagnostic test mode, then let us know what happens and we'll try to help you further. Include the model number of your washer with your response.

The red light is on but wont turn off. I cant start the washer.

@searspartsdirect

7 жыл бұрын

Megan, it sounds like the red light you’re referring to is the lid lock light. You can watch this video-- www.searspartsdirect.com/article/how-to-display-error-codes-on-vertical-modular-washers-vmws-video.html-- to help you troubleshoot the problem with your washer. The washer won’t work until you fix the problem that’s causing the red light to flash.

"it's not this, it's that"

The only light that stays on is the sensor light and nothing happens. I can hear it clicking like it wants to do something?

@searspartsdirect

7 жыл бұрын

The sensing light stays on if the lid doesn’t lock. The clicking may be caused by the lid lock trying to engage the lid strike. Check the lid switch plastic bezel on the top panel that the lid strike inserts into when you close the lid. If you find that bezel loose, pull it forward slightly until it clicks. Tightening the bezel might allow the lid to lock so the cycle will start.

@danmcdonald1163

6 жыл бұрын

ethan polasky

11021202011

Dont Flash The Lid

before anything else RESET your machine...

@kanewes5768

7 жыл бұрын

chris venegas

@pheno23

5 жыл бұрын

How

This place is a JOKE. Ordered an IN STOCK PART for our Kenmore Washer. Paid in Full. Didn’t arrive today as ithey said it would so 😮checked on site and NOW SAYS ON BACK ORDER. We sit with no washer. WHAT A JOKE

@ZombieQueeen

10 ай бұрын

….this isnt yelp

"it's not this, it's that"