I have a new carb. from Amazon that just came in the mail for my Stihl trimmer. I didn't even go to the Stihl dealer and ask how much an OEM carb would cost when I saw the prices on Amazon. OEM prices are so out of line that if you can fix it yourself, it never pays to take it to the dealer for repairs. The price of OEM parts is the main culprit.

@HomeGaragechannel

9 күн бұрын

you bring up a good point about prices. I always wondered why they were so expensive

30 years as a certified OPE technician, and Stihl Master Service tech, and everything you did in this video is exactly what we do in the shop. Sure, I give the quote to the customer with the OEM carb, then another with a carb off Amazon, and truth be told, the Amazon cheapo carbs works just fine, my advice is just go with that. Never even bother wasting time trying to clean the carbs anymore, it's a simple matter if "when in doubt, throw it out" when it comes to carbs. One thing to remember though, Stihl's hate inferior 2 stroke oil. Try to stick with Stihl oil, Castrol (they make it for Stihl), Lucas Oil, or even Echo oil. Using cheap oil or outboard marine motor 2-stroke oil will destroy a Stihl in short order. I mean it, I cannot stress that enough, I have a boneyard of FS130's and BR600's that were only a few months old but were destroyed because the owners chose to run cheap oil in the fuel mix.

@HomeGaragechannel

Жыл бұрын

thank you TJ Clarke for your time and sharing your experience

@gnaedigerfels

Жыл бұрын

Stihl 2-stroke oil is literally one of the worst... even if you buy a very cheap one, it will be fulfill the same JASO and ISO standards... look it up, I'm not joking

@tjclarke4604

Жыл бұрын

@@gnaedigerfels LOL, yeah sure, I thought that too when I was 19, until I learned better. I don't need to "look it up" I have my certs, so your comment isn't even worth wiping with. Go ahead, run your cheap oil in YOUR Stihl, but don't come whining back to the dealer or technician when it locks up on you. Another ham & egger. Sit down.

@michaelcountryman9130

11 ай бұрын

Next time you get a spark gap it at 0.30 and never ever put a pre gap plug in any engine always check the gap.

@lopez454ss

8 ай бұрын

gotta get the full synthetic @@gnaedigerfels

I find it far more economical and way less stressful to just buy an aftermarket carb. Some of the time they even include fuel filters, fuel line, extra bulbs, etc.

@HomeGaragechannel

Жыл бұрын

I feel the same way.

@calebmoody326

Жыл бұрын

I recently put a new carb and gas tank on this exact weed eater. If I buy I new carb I try to buy one from my stihl dealer. They’re usually better quality than the cheap ones online.

@bobbyhempel1513

9 ай бұрын

​@@calebmoody326you know that stihl does not make their own carburetors and you can buy them from the manufacturer for half the price right.

@mtnmotoadv

2 ай бұрын

@@bobbyhempel1513 who's the manufacturer?

I’ve sold stihl equipment for 15 years and worked with top mechanics. Most of the problems we dealt with were bad gas , cheap oils or ethanol!

@HomeGaragechannel

4 ай бұрын

thanks for sharing

I've been watching many videos of fixing trimmer carburetors and this is, I believe, the best that I've seen so far. Straight forward, to the point and no fluff. Thanks for a great video. I will be looking out for you in the future.

@HomeGaragechannel

5 ай бұрын

thanks, that means a lot

I just got through installing my new China carburetor kit . It was $19.98.Everything was easy, went back together perfectly! It even came with new hoses, two extra fuel filters, a spark plug, and two extra primer bulbs. Which I replaced all of it. Other than an idle adjustment, I didn't have to adjust anything else. And now the weedeater runs perfectly! Thanks for the info sir.

@HomeGaragechannel

10 ай бұрын

no problem and good work !

Thank you for your videos. I enjoy your troubleshooting process and your clear instructions. Please make more content.

@HomeGaragechannel

Жыл бұрын

I will and thank you Ruben Contreras

You made the correct decision...get the aftermarket carb, because more than likely it will last nearly as long. The important point here is Maintenance, Maintenance, Maintenance....and keep maintaining it.

@HomeGaragechannel

Жыл бұрын

you are correct, hopefully though they'll take better care of it this time.

Working at a dealership of Stihl products i can say, yes stihl carbs are pricey. we've tried aftermarket and it's about a 50/50 shot they'll work. So we typically we stay away from them, just for the hassles sake and possible doubling the time invested in repairs. But for homeowners, i say go for it.

@HomeGaragechannel

2 ай бұрын

you make a good point, aftermarket is fairly "Iffy" and if you want an almost guarantee, go OEM.

I think you made the correct decision. You might have considered a carb kit, but those are pricey too. If you were running a commercial shop, let the owner decide, but you're doing this as a hobby..you get the idea. You got it running, that's what matters.

@HomeGaragechannel

Жыл бұрын

well said and it makes sense to me.

Good video! Over the years as a farm equipment/ lawn & garden tech, I've grown into the "Never-seize" habit. Spark plugs, exhaust hardware, etc get a dab of the stuff.

@HomeGaragechannel

Жыл бұрын

interesting, I'll have to check it out.

@apatterson8128

11 ай бұрын

Like the Franks’ Red Hot commercial, “I put that $#&@ on everything!” Lol

Nothing wrong with ordering the aftermarket carb because it's an easy way to at least have a rebuild kit if the cheap carb doesn't work well you can use the parts to try rebuilding the original carb. It's a great plan 😁

@HomeGaragechannel

Жыл бұрын

nice, I thought it was a good idea .

@patthesoundguy

Жыл бұрын

@@HomeGaragechannel Yup it's a fantastic idea because you simply can't lose with that deal and it's only a $20 gamble in the first place. 👍👍👍😎😎😎

Thank you for sharing your knowledge. I have two STIHL Brush cutters, but the big FS 240 (not an R model, mine has motorcycle handles).failed to start or even try. The air filter was filthy and I did my best to clean it with my compressor, but still no joy. Spark plug looked fine, fuel in the bulb and couldn't find any spark arrestor on my European model, but noticed some green stuff in the exhaust box holes so poked them and a load of green powder dust came out. Some critters must've made it their home over winter and blocked it. After a general degunge, gave it a pull and she fired first time. Will go order or buy a new air filter tomorrow, but the triangular bladed was needed over the smaller model wire today to cut some really tall thick weeds where as the wire would've been constantly requiring adjustment.

@HomeGaragechannel

Ай бұрын

very nice work getting it working again!

My Echo straight shaft brush cutter, leaf blower and pole chainsaw all eventually would not start. I cleaned and put a kit in the brush cutter carb but it still wouldn't start so I installed a after market carb and it started right up and has been running perfect now for three years. When the other two machines quit I went with new carbs out of the gate. All three run great and start easily. I started using racing fuel three years ago and believe the ethanol free, leaded fuel with no additives helps keep the fuel systems in good working order when not being used regularly.

@HomeGaragechannel

Жыл бұрын

nice!

Your videography has gotten quite good. You made the right decision on the carb. Your co-worker should be a happy customer.

@HomeGaragechannel

Жыл бұрын

thank you Marshall Collins

Thanks for sharing. You’re knowledgeable on this subject matter, it’s greatly appreciated.

@HomeGaragechannel

3 ай бұрын

Glad it was helpful!

First, when I’m done using any of my two cycle equipment I dump gas back in the fuel/oil mix gas can I have. Then I start and run it until it quits. I was all the gas out of the carburetor that I can get out. I work on my own stuff and have used after market carbs on repairs I’ve made with very few issues. So I don’t fault you for using them. Thanks for the video.

@HomeGaragechannel

Жыл бұрын

wow, excellent methods and thank you ussreeves

I like the thrill of the chase. Lol. It’s only a hobby for me. Sometimes I eat the bear, and sometimes the bear eats me and I buy an aftermarket carb. No judgement either way as long as the darn thing gets up and running. Thanks for your time HG

@HomeGaragechannel

11 ай бұрын

well said and great comment!

I love aftermarket carbs and always recommend them. Some customers still insist on OEM which is fine if they are willing to pay for it.

@HomeGaragechannel

Жыл бұрын

you got that right, but most customers are cheaper than you think. Thank you Brian King.

I feel like with quality fuel, oil, and maintenance, any carb will last sufficiently long to justify it. I use A LOT of aftermarket carbs, especially on 2 stroke equipment. I find cleaning them, even in my ultrasonic, is sometimes hit or miss. There's a lot of little check valves on the ones with the built-in primer bulbs. I use a small jar (Peanut butter, etc) that is clean to put my 2 cycle carbs into the ultrasonic. I use the same gas I would use in equipment, in the jar. I find this does a very good job on cleaning these items, and doesn't immerse it in even more dirt/grime than was already with it. Ultrasonic makes it MUCH easier to clean the more gummed up mower/pressure washer carbs. I've put some pretty nasty ones in it, and with a good degreaser & dawn dish soap, they come out in much better shape. I still use my carb spray to rinse and help unclog small passages that may still require my pokey tool. I will disassemble the carb early in my process, put in the cleaner and during the 10-15 mins, allows me time to remove wheels (lubricating), sharpen blades, etc. Once it's done, I'm ready to assemble everything.

@HomeGaragechannel

Жыл бұрын

thank you for the advice and tips Matt Wickert

One thing I always do when an engine won’t start is put in fresh fuel and remove the spark plug to add a bit of fuel directly into the chamber. It is surprising the number of times the machine starts and then just keeps running. I run the machine for 15 or 20 minute, which will tend to lubricate the diaphragms and unblock the carburetor.

@HomeGaragechannel

2 ай бұрын

it works sometimes, but you can't always save a hardened diaphragm that needs replacing.

@bl9531

2 ай бұрын

@@HomeGaragechannel definitely does not always work but it is worth a try! Thx for another excellent video

@HomeGaragechannel

2 ай бұрын

no problem and thank you

Thanks, this is very interesting as I've faced similar issues with my 2 strokes.What works for me is to buy an OEM rebuild kit if possible and then also, a pattern Chinese carb for standby.I found in my Stihl fs 50, strimmer , both diaphragms were very tired after only two seasons 😢, the fuel pump diaphragm seems to be made from acetate and the longevity is poor in my machine. So no problems for me with a pattern carb as it can't be any worse 🙃 .Best Regards and thanks again 😊 Ian 🇬🇧

@HomeGaragechannel

Жыл бұрын

thank you Ian.

You did the right thing. I had the same issue and ordered an after-market carb from Amazon for $13.00. It saved me a lot of time, and it worked perfectly. 😊

@HomeGaragechannel

Жыл бұрын

thank you John Davis

Nice job. Pro tips are awesome. Spend 10 minutes on the carb and if you need to replace go for it. I’d probably do the OEM but I’m not a small engine shop. Most customers would opt for aftermarket too!!

@HomeGaragechannel

Жыл бұрын

nothing wrong with it, and if there was any time an OEM carb is worth it, it would be on this machine, thank you Phil Del Giudice

The carb looked very clean but the diaphragms had hardened. I personally would have purchased a carb re-build kit and tried to correct the problem that way. If the rebuild failed, I would go with the aftermarket carb like you did. I have this trimmer BTW and did rebuild mine successfully.

@HomeGaragechannel

11 ай бұрын

Great point!

i found that when you clean a spark arrestor, its best not to use a wire brush. This is because when scratched, it creates a much better bonding surface for the carbon to adhere to. I like to use compressed air, but most of the time you dont have to use either. Nice job, appreciate the fine work

@HomeGaragechannel

Жыл бұрын

thanks

@hoyt_arms

Жыл бұрын

Its best to throw the arrestor in the garbage lol

@AlessandroGenTLe

11 ай бұрын

Just use a brass (instead of steel) brush

😅 i do the same you do.i am cheap.and when i fix equipment for friends.i ask them if they want oem parts or aftermarket.and they do the same.aftermarket parts.thank you for taking time to do this educational.videos.

@HomeGaragechannel

Жыл бұрын

no problem and thank you Christian Vasquez.

Great instructional video thanks

@HomeGaragechannel

8 ай бұрын

thanks

Thank you a lot! I really like how you explained in your videos about how to fix this machines I hope I can fix my weed eater Fs91r which start but it dies…

@HomeGaragechannel

2 ай бұрын

thank you and good luck

You did exactly what I would've done....Nothing wrong with doing a budget repair job.

@HomeGaragechannel

10 ай бұрын

thank you!

Excellent videos! Thanks so much

@HomeGaragechannel

10 ай бұрын

You're very welcome!

Very good video , I agree with the after market carb

@HomeGaragechannel

Жыл бұрын

thank you Michael Martt

I have a fs90r.i love it! I start my equip,in the winter,

@HomeGaragechannel

9 ай бұрын

very nice!

I had to replace the carb on my KM130 last week. Got an OEM one for $125. It wasn’t cheap, but that’s the first repair in 13 years. The machine runs like new now.

@HomeGaragechannel

25 күн бұрын

wow.. nice machine!

I'd probably give them the options and then it'd all be on them. If I hadn't broken the throttle shaft on the carb on the electric start I'd have cleaned/rebuilt it but had to get a knockoff BUT it works fine after I worked out the primer issue. Thanks and Happy Weekend

@HomeGaragechannel

Жыл бұрын

that's a good idea.

@lewiemcneely9143

Жыл бұрын

@@HomeGaragechannel I get blamed for enough as it is so if I can spread it around it works better. Cuts down on the hollering.

If it is ok with your co worker then you did the right thing. Great video

@HomeGaragechannel

Жыл бұрын

I sure hope so, since they didn't tell much about it, I just did what I thought was right, thank you Growling Little Country homestead.

My older stihl stuff is still going . Newer stihl stuff is too expensive.😊 And I've never had a problem with after market carbs.

@HomeGaragechannel

Жыл бұрын

nice, thank you for letting me know

I would of done the same thing. Great repair 👍🙏👍🙏

@HomeGaragechannel

Жыл бұрын

thank you RayFpv.

Had A Stihl Trimmer...Nothing But Carby Problems.Changed To A Honda...Perfect

@HomeGaragechannel

3 ай бұрын

great choice

ive had good luck with cleaning carbs never had to buy a aftermarket thank god but the only time i would consider is if it was my personal machine and i really liked it lol

@HomeGaragechannel

Жыл бұрын

nice, how many have you had to clean do you think?

@sluger3647

Жыл бұрын

Maybe 14 or less im still new to these machines I love learning bout how they work though

A neighbor brought over an antique Stihl chsainsaw and the carb was really messed up. A new OER carb was 'way too much $$$ so we bought a Chinesium version at $12.00. It included a new spark plug, a new ignition coil, a LOT of fuel line, the clunk/filter, the air filter and the carb. I put it on and in three pulls it was running perfectly. I never had to adjust anything! It's still running with the Amazon $12.00 carb three years later and - frankly - if I had to buy a new one for every new cutting season - we'd still be money ahead compared to buying just one Stihl carb.

@HomeGaragechannel

Жыл бұрын

wow nice, and yes for what they are, the aftermarket works great!

Same issue with my Stihl. Used after market carb which worked fine.

@HomeGaragechannel

10 ай бұрын

Good to know

well for me i,d check with the types of choices online and see what,s good on price depending on where i live and what the good reviews are on the products out there etc.

@HomeGaragechannel

Жыл бұрын

I always forget to check the Reviews, but I think that's important too.

I would have first looked for an OEM carb rebuild kit. Second choice would have been an aftermarket rebuild kit. I want to keep as much original parts on my Stihl equipment as possible.

@HomeGaragechannel

Жыл бұрын

that makes sense

After market carbs work good for the most way to go

@HomeGaragechannel

Жыл бұрын

I think so, I don't think they'll last as long as the OEM but with care, it will last a few years.

Bought new Stihl OEM carb 45$, after 11 mos stopped working ! Dealer told me to pound sand. 15$ Chinese carb (HIPA KIT) and back in business with new fuel lines,bulbs,plugs,filter included also. So Done with oem

@HomeGaragechannel

Жыл бұрын

wow that dealer was mad. Were you asking for a new OEM carb to replace it?

If the after market carb works just fine,then that’s the one I would be buying. Good choice my friend.

@HomeGaragechannel

Жыл бұрын

thank you William Snow.

i like that... going on a vacation and not really wanting to be there for how ever "long". Q. for ya though... if it were me i would like to keep the original carb. just to have on hand and know with careful handing i could have a successful o.e.m. rebuild, and to put that back into my stash for a rainy day. what would you think bout doing something like that or do you already have a small stash?!?

@HomeGaragechannel

Жыл бұрын

I have a stash of metering diaphragms but I don't carry full kits, simply too expensive

Great video. Only thing is I was waiting to see if you would replace the fuel filter and how you would pop that cap off the fuel tank can you give me some insight into how you might do that mine looks exactly like yours, the cap that is and I'm afraid to break some plastic and removing it cuz I know my fuel filter is clogged but I can't get to it any other way. Thank you.

@HomeGaragechannel

Күн бұрын

you mean the plastic spoon looking thing connected to the cap? Just use some pliers to grab it and pull it out. The spoon will "lightly" deform to allow it to come out.

was curious on the engine having valves when the oiled fuel was mentioned, apparently it’s a 4 stroke that doesn’t have a sump and uses the fuel oil mixture like a 2 stroke, funky

@HomeGaragechannel

11 ай бұрын

yes you are correct, it's quite ingenious but the design is a bit over kill.

A few days ago, I was working on a newer echo string trimmer and when I was pulling on the rope to try to start it I noticed that it was pretty quiet which was strange but when I took off the spark arrestor screen I found the first problem the spark arrestor screen was completely clogged with carbon so much so that the engine was not starting on the feel that I put into the carpets throat but after I clean the spark arrestor screen the engines running really well

@HomeGaragechannel

8 ай бұрын

hey nice work!

@josephmeadows8521

8 ай бұрын

Thanks😁

i have always been very apprehensive about aftermarket/knockoff carbs that aftermarket carb looks exactly the same as the original and performs well i'm quite surprised you didn't have to change the mixture screws my dad dropped off his honda 35cc brushcutter today saying its leaking fuel a quick look and its leaking tons of fuel out of the carb both sections where the membrane material seals the carb sections called honda $106AUD for a new carb i don't think so if its too far gone i will be going down the same road you did

@HomeGaragechannel

Жыл бұрын

I understand what you're saying

The real culprit in these carbs with the purger/primer bulb are the non return valves in their black base. If either of them leak the metering diaphragm will not function properly. Replacing that part will get the OE carb going. But the AM carbs are a hit or miss for this reason. Their non return valves dont hold properly sometimes out of the box. For this reason i have adapted after market chainsaw carbs on my FS130 and fitted a seperate purger that is used on the FS 120/200/250/400 etc. These carbs are more generous in their scope of H and L adjustments and offer a longer service life, though the initial work for adaptation is quite a lot. Post script. Sometimes the purger valves can be cleaned by pumping liquid detergent and water , with it fitted on a old carb body thathas no metering valve. But that is a gamble

@HomeGaragechannel

4 ай бұрын

thank you for sharing that

Great video, very informative. I just put a Chinese carb on a stihl FS 110 4 mix. It runs great but will not start unless I prime it with gas down the carb. Brand new purge bulb seems to work perfect. Any ideas why this would be? If I have to start it this way I can live with it cause after it starts it runs and restarts great. Thanks again.

@HomeGaragechannel

3 ай бұрын

I'm scratching my head on this one. If I recall that carb is purely a "choke" style carb, meaning if it's not starting with out "physical" priming, then there might be a problem with the machine. Have you done a compression test yet? I wonder if it's low, and causing the engine to have a tough time pulling the air and fuel into the engine.

Good job 👍

@HomeGaragechannel

11 ай бұрын

Thanks 👍

Some of the aftermarket carbs are better quality than others, I try to replace the gaskets/diaphragms but if the carb pretty bad, then I’ll replace.

@HomeGaragechannel

Жыл бұрын

you are correct, thank you Shoney's small engines

u did good... gj .. same i would have done!...im do alot carbs - ALOT- so im rare case- i replace the inside parts and i renew the needle /seat hole ! :>).. basically rebuild the old carb.

@HomeGaragechannel

10 ай бұрын

nice and thank you

I'd buy the after market frankly as well. Question though have you ever had one of the stihls leak out of the tank vent? Did you just replace the vent or is there a way to "fix" it?

@HomeGaragechannel

Жыл бұрын

no I haven't and if happened to me, ... I'd probably just replace the entire cap, just easier

I ordered a carb. It came several weeks later from China. I put it in and it ran perfect without adjustment. I took out the little screen. Why do you need two intake filters. Now, I only use the high dollar gas but I only use the Stihl for the heavy jobs with the metal blade. For my normal trimming, I have a DeWalt, 60V trimmer with the companion blower and chain saw. At 87, I need to conserve energy and stress.

@HomeGaragechannel

Жыл бұрын

very nice, as for the filters, the outside one is meant for larger items like grass and it's easier clean.

Well done Thanks for useful information I have fs450 sthil trimmer I need replace recoil but we haven't in our stores I need your advise from any brand to get recoil to can run it again

@HomeGaragechannel

2 ай бұрын

I really don't have any resources to help out.

@mohmedhosny6094

2 ай бұрын

@@HomeGaragechannel I need your e mail address for more information

Hey HG I find myself fixing 8 to 10 year old machines that are not on there last leg but have maybe a few years left on them. I find using OEM parts on a machine that is not worth the price of the part silly and bad investment into the machine . I am upfront with my customers and let them know I can get a clone carb for 1/2 the price of a OEM and they usually work out great . If I have a machine back becasue of the clone part I will replace it again easy. Now if I had a customer come in with new say blowder and can not get i to run for ny reason I would suggest a OEM part for the machine no question .

@Mrcrowley1967

Жыл бұрын

Bty the way my dad had one of those syhl trimmers you could not kill it put a blade on it and it would slice through sablins like butter .

@HomeGaragechannel

Жыл бұрын

I like the way you put it.

@HomeGaragechannel

Жыл бұрын

that sounds like a great idea!

Personally I would have gone with an OEM carb kit, but aftermarket is fine too.

@HomeGaragechannel

Жыл бұрын

you're right the OEM carb would best

I find the 4mix engines have a lot more issues than the good old 2 stroke engines

@HomeGaragechannel

Жыл бұрын

I've heard the same thing too.

@briantii

Жыл бұрын

Personally I’ve had better luck with the 4mix, though I have found valve adjustments are needed more often than Stihl claims.

@tjclarke4604

Жыл бұрын

@@briantii spot on. Stihl says once then you are good, but heh, nope, you gotta check those valves often. And it literally only takes 10 minutes, unlike what the dealership tries to bill you for.

@briantii

Жыл бұрын

@@tjclarke4604 And 10 minutes is if you're really taking your time. It's crazy how quick and simple it is to do.

@tjclarke4604

Жыл бұрын

@@briantii Yeah it's true, 10 minutes would also include finishing up the work order and waiting for the gasket and sealing ring from the parts dept to show up at your station. But the dealership will charge the customer and hour, plus shop supplies.... terrible.

With the carbon on the spark plug might check what kind of oil has been used to mix the fuel,maybe another brand would give less carbon (although the screen didn't look too bad)

@HomeGaragechannel

Жыл бұрын

good idea

I usually just buy a rebuild kit. It has all the parts I need and it costs less than an amazon carburetor.

@HomeGaragechannel

4 ай бұрын

that works too.

I would always start with a carb clean first in the ultrasonic tank, some carb cleaner and then replace the diaphragms. This works in most cases. If that doesn't work due to an inaccessible blocked passage or one-way valve, then I'd replace the carb. Some of the clone carbs come with problems. I had one with a mashed spring in the metering area and another with a tip on one of the jets missing and another with a missing non-return valve. The only 100% guaranteed fix is to put a new, genuine carb on, but they are expensive.

@HomeGaragechannel

9 ай бұрын

that sounds like a plan

Mine had similar issues. I bought a cheap carb and stolen the parts failed on the oem one. Oem parts expensive and you can't always find them. Works like new after few hours of use.

@HomeGaragechannel

Жыл бұрын

nice work, and thank you for your time Ingihan

After market is the best choice 👍

@HomeGaragechannel

7 ай бұрын

in a lot of cases, yes it is .

People just don’t know how to maintain or store equipment from one season to another. They are just to busy to do such mundane stuff, like storing their equipment properly. If it fails to start nex spring they will buy a new one. Every fall I set aside a day to put certain outdoor equipment in storage condition. I crank them up and let them warm up for five minutes. I then pour out all the gas, recrank them and let them idle until they stop for lack of gas. If they have a primer bulb I press it until it is empty while it is idling. I don’t want to leave any gas in the unit when I am through. I then wipe the off with a slightly oily shop rag and hang them up in my shop by their cutter head until next spring.

@HomeGaragechannel

Жыл бұрын

you couldn't have said it any better.

I have a question about a Stihl blower. It’s a br400, we have changed the carburetor and the spark plug. We checked the compression. It’s all good but it only runs on starting fluid. What what you think the problem is.

@HomeGaragechannel

Жыл бұрын

answered this question already

Just changed the carb and mine fires up now but cuts out quickly. I am missing the air filer cover and the screen that you cleaned at the beginning seems to be missing would this be a reason? I thought it might still ring but ring rough

@HomeGaragechannel

Ай бұрын

not at all, you need to make some adjustment to the carb to get it to work with your particular engine .

i used to have this same machine gearbox maybe was gone but i did some redneck engineering and the head worked again.

@sluger3647

Жыл бұрын

redneck engineering sometimes is the best thing u can do

@HomeGaragechannel

Жыл бұрын

nothing wrong with that

@TheDennys21

Жыл бұрын

"Redneck engineering" hahahahahahaha

In this situation, the cheap carb, it works and unless the customer changes his ways a OEM carb would be a waste of money.

@HomeGaragechannel

Жыл бұрын

you make a good point

I cleaned my stock carb and ordered a $9 rebuild kit. $11 Cheaper than an aftermarket carb.

@HomeGaragechannel

Жыл бұрын

nice work!

Hi I do not know if there any differences within the carbs oem or aftermarket. I tried one aftermarket on my medium high expensive trimmer. It do not run perfectly and it is not going smooth. I tried to adjust it but it does not help. BUt it could be some other issues like the compression. For me I have to buy a special adapter for the compression-tester to fit into the spark-plug hole. The new OEM was really expensive and I do not think that would help to buy a new one. I would never buy a OEM because of the high price and it is the same construction or almost the same. Tried many hours to clean carbs. That for me does take a long time and does not work for me. Tried air compression, sonar cleaner, brake-cleaner etc etc...I gave up...For me I have to check the compression next step. Thanks for the interesting vid.

@HomeGaragechannel

11 ай бұрын

no problem and hope you figure it out.

What do you think about stihl ultra oil they make you run for warranty? I like echo red armor.

@HomeGaragechannel

8 ай бұрын

I've never used the oil but if you care about the warranty then i would definitely keep using it.

How long would the oem carb last vs aftermarket? If there's no difference is the right move.

@HomeGaragechannel

Жыл бұрын

well, that's a tough one, if they were both treated well, probably pretty good, but mistreat the both of them, I'm going to guess the aftermarket carb wouldn't last as long. it's up to the owners to make that choice.

Im selective on the OEM replacement, like unless i really have to, i go for the aftermarket ones

@HomeGaragechannel

Жыл бұрын

makes good sense to me

I would ask the owner which way he wanted to go, but for me, after market carb.

@HomeGaragechannel

Жыл бұрын

best choice ever

I've gotten comfortable with off brand carbs when the cost of the repair gets close to the value of the equipment. OEM carbs are insanely high on a lot of stuff I've come across and rarely do I have any issues with the off brand ones.

@HomeGaragechannel

Жыл бұрын

you got that right, it's about money, and thats it for me. Thank you Shaun Riley

How is it you were turning those screws counter clockwise as yiu were inserting them?

The blockage maybe in the muffler; the whole muffler should be cleaned I soaked mine in degreaser and run the hose and the airline through it. On my troybilt engines the spark arrester screen can't be removed from the muffler, so I clean the whole muffler.

Great video.

@HomeGaragechannel

3 ай бұрын

Glad you enjoyed it

The comment about the co worker who is better off in the same job 😅. I've been there but on the other spectrum with more vacation and pay than someone who has been there much longer. It's all about negotiation and making sure that the company understands that you are an asset vs liability. Not there anymore but I got in trouble for someone seeing a pay stub while in my vehicle. (Which was much nicer than coworkers) I didn't even show it but dude saw it. He didnt get the $3500 Christmas bonus but $700. He had a thats not my job type mentality, and I was more adaptable and would float around to help if needed. He still works there and is miserably content and I work for a nascar team. I'm also a middle school drop out with an outstanding amount of knowledge in electrochemical engineering, crane engineering, and R&D Tire engineer for race teams. I have no debt and own everything in my possession. Technically nobody ever owns anything I guess, not even freedom

I would ev trued to replace the diaphragms in there or rebuild kit if 1 available,but for a fine machine like that,a new carb it deserves good job

@HomeGaragechannel

11 ай бұрын

sure does and you couldn't have said it any better

Did all these repairs and still not starting. Original problem was hard to start when hot. Also air filter was oiky? Discovered there is a gas tank vent that may be blocked but having trouble removing it. My KM90R is 10+ years old and used hard! Have vent ordered as stem seemed to have debris in it. Also w/e wouldn't run with air filter. Have you done video replacing tank vent?

@HomeGaragechannel

2 ай бұрын

no I've never had to deal with the tank vent before. Have you considered a new carb yet?

@judisinger3693

2 ай бұрын

@HomeGaragechannel yes, new carb, fuel lines, filters, new fuel lines, connector, new coil, plug. Last time it started it wouldn't run with air filter in? Vent arrived today. Will try starting it again before I take it apart again. Bulb fills up so don't think it's a fuel issue. If won't start I will try to change vent which appears hard to remove as was the connector. When I first took it apart air filter was oily, but didn't know why, I hadn't seen vent video!

I usually keep the old carb order a rebuild kit and then do it up when I have the time hey when another one comes in you have a working carb

@HomeGaragechannel

Ай бұрын

good idea

Ive never been able to starr my brand new FS 91 R trimmer and I bought the pre mixed fuel that Ace sells you so you can get the extended warranty. Should I just make a warranty claim?

@HomeGaragechannel

10 ай бұрын

possibly but I'd have someone else try and start it, and see if there's a difference

i use after market carbs all the time .i get things cheap or for free because of people using reg gas that has ethanol/water rather than premium /straight gas .the water tends to corrode the aluminum or gum them up not letting floats work .if anyone complains about what you do maybe they have ocd ...lolo good job on the video.

@HomeGaragechannel

20 күн бұрын

great choice

A lot of carb issues , due to running dollar store 2 stroke oil, and letting your equipment sit , with fuel in it. Fuel turns to crap in 30 -40 days. Had the same stihl weedeater for 20 years, no issues, but o ly used Stihl 2 stroke oil. And when stored , treat the fuel with Sta-Bil. Bought myself a 99 R , third year , again no issues.

@HomeGaragechannel

Жыл бұрын

thank you Ronnie Cox

you did the right thing.

@HomeGaragechannel

Жыл бұрын

thank you Sam J

The cheap Walmart brand is just about as good and it’s cheaper to fix also 😊😊😊 At the price you can just get other one and keep working 😮

What do you do with the old carbs after replacing them with a new one ? I would sell or keep parts of them like the left over parts from the rebuild kits i've kept over the past year 😃

@HomeGaragechannel

Жыл бұрын

I just keep them in a box, don't do much with them. They're like little trophies

@lucasbergfors9446

Жыл бұрын

@@HomeGaragechannel cool sounds like a small engine mechanic's trophy collection to me 😄

@HomeGaragechannel

Жыл бұрын

yes it does, I like looking at them and remembering what I did

@lucasbergfors9446

Жыл бұрын

@@HomeGaragechannel i would have done the same, i do that with old pistons and rings too i even got some old diaphragms and other old parts even at the machines i work on and preserve 😄

Hey thanks for your videos, Ive recently been given a FS 130 that runs very poorly. Ive been going through the check lists of things to do to get it running well again, i have recently ran into a problem where its very difficult to pull the string to start and feels jammed. Ive just checked the recoil assembly and adjusted the valves. but still having troubles. any idea where to look next or what it could be? Thanks!!

@HomeGaragechannel

9 ай бұрын

interesting, take the plug out and then try pulling it and see if anything comes out of the spark plug opening.

@Henreko150

9 ай бұрын

@@HomeGaragechannel Thank you ill give it a try and let you know !

@Henreko150

9 ай бұрын

@@HomeGaragechannel Wow interesting when I pull the cord and the spark plug is off, it pulls fine. But when I put the spark plug back in it jams again. What could that be?

@HomeGaragechannel

8 ай бұрын

is the plug the right one? if the plug is too long it will make contact with the piston

@Henreko150

8 ай бұрын

@@HomeGaragechannel Well I’ve had it running before with that same plug in

I would have put the $8 kit in it but carbs for that ar almost $40 here in Canada

@HomeGaragechannel

Жыл бұрын

is that the price of the OEM rebuild kit, or aftermarket?

@RussellHoughton

Жыл бұрын

@@HomeGaragechannel aftermarket

@HomeGaragechannel

Жыл бұрын

wow!

I've seen you do a lot of these videos and you've always just cleaned the carb and replaced the diaphragms. I noticed that these diaphragms are different. Did you replace the carb because the diaphragms are more expensive, and/or you didn't have any to match?

@HomeGaragechannel

Жыл бұрын

it was the pumping diaphragm, I was too far gone to rejuvenate and I don't carry it either. If I have to replace the purge bulb, metering and the pumping diaphragm that's enough for me to just replace the entire thing.

I've just replaced the carb on my BG86c blower but i bought an OEM carb for £90. After watching this, i wish i had spent £20 on an aftermarket carb instead 😂

@HomeGaragechannel

2 ай бұрын

at least you know now

Taking the screen out is the best solution to fix a clogged spark arrestor

@HomeGaragechannel

Жыл бұрын

it's an easy way to fix it for sure

@Home Garage Would replacing the diaphragm(s) be affordable? Or would this be opening up a new can of worms?

@HomeGaragechannel

Жыл бұрын

it's worth it for the most part, it's just that sometime there's an issue with the carb itself

In the UK these machines (I'm adjusting a km85r at the moment for a friend) are £800-£850 new. If I needed to get those 2 diaphragms new it would cost me £22.90. A new carb would be £75, with a machine this expensive to buy, I would stick to original parts. If I can afford the machine, I can afford to buy the parts from Stihl.

@HomeGaragechannel

7 ай бұрын

you make a good point