Thank you ! I just purchased a fardriver and I'm just waiting for the Bluetooth adapter, Great videos absolutely helpful in so many ways.

@EVCustoms

9 ай бұрын

Thank you my friend... i will make many videos in this particular controller, so stay tuned..

Im from indonesia, i like your videos, i can to self learn from your video Thank you sir good job 👍

Thank you for this info and the series. You are very knowledgeable on a vague subject. Thank you again 😊

@EVCustoms

2 ай бұрын

Thank you mate! 😁

Все четко обьяснил, дисплей отличный, жду продолжения! Спасибо )

@EVCustoms

9 ай бұрын

Спасибо Алекс.. 👍

Thanks for all your hard work.

@EVCustoms

7 ай бұрын

Thank you man.. 👍

Very helpful, thank you

Where did you buy this display? Its possible to set mph instead of kmph?

Podrias dejarme el enlace de compra del display?

Hello. Thank you very much for your videos, they are quite clear and explanatory. They have been very helpful to me. Regarding the display, do you sell it? or could you leave a purchase link?

Thank you. Great video. I am very much interested in Fardriver controller. Will the display settings and everything ODO etc persist after battery removal or not? Planning to change my ebike controller from Savboton to Fardriver but the display situation has alway put me off.

Can you maybe help me. I recently buy one motorbike when the battery lithium 72v 30 Ah is connected, it always shows as 100% full with four bars on the speed display. However, the issue is that the bars do not decrease while driving; it remains at 100%. When I travel around 50 kilometers , the battery runs out but I only get the low battery signal with the icon appearing just about 30 seconds to a minute before it's completely depleted. This means I never see the battery level drop; it's either full or empty, making it very difficult to manage the autonomy, knowing when to recharge, especially since it could run out when far from a charging point.

I want to buy a 72360 with the display shown in the video. Where can I purchase it?

Hi , Can you please help me, my MTPA on the phone , shows Red and not green. please advice. thanks

This must be why on the generic controllers I use lately with no display the 3 speed does not change motor speed. They are set to 0 at the factory. But I have older controllers that the 3 speed does work. Also the controller low voltage cut off on my 48/60/72 volt controller is set to 42 volts for a 48 v battery. I was using a 52v battery and the BMS must have no over discharge protection because it did not cut off till 42v. Not good.

Which pin in the board of controller for single line digital speedometer? Because i can't found the light blue wire on the my controller. And the wiring colour is very different with your controller.

how do you know to use the light blue wire from the controller to the screen?

What lcd panel is that. May I have link

Can I use induction motor to drive my rear wheels.

☆ HELP ☆ HELP ☆ why can I not connect to my 72450 FarDriver from the FarDriver app. Someone else is bound, guy says it won't let him connect to unbind. Please help

What display model?

Any link to that display ? is it a SIAECOSYS variant ?? none seem to show the multimedia option like yours.

@EVCustoms

6 ай бұрын

Hi.. i bring them straight from factory by agent, no is not Siaecosys variant, this one is universal screen for FarDriver and Votol controllers

hello could you please tell us the model number for this display so i dont get it wrong when i order thank you very much

where can you buy such a display?

Can you also tell us more about the CAN control, Can you please tell me how we can connect this display with the BMS using the CAN Protocol, to check the available range? Thank you so much for this awesome video.

@angusmcgil

5 ай бұрын

all you have to do is connect CAN H from the bms to CAN H on the display and CAN L from the bms to CAN L on the display just these 2 wires is all thats needed and then enable the CAN protocol in the bms app,some bms can only enable CAN protocol using the pc app

@sharmatechtalk

5 ай бұрын

@@angusmcgil thanks man..

Will this work with a 5k watt motor?

Hi bro How did you find the number of pole pairs, if we do not know the pole pair of the motor, how can we find out (without opening the motor)

@EVCustoms

7 ай бұрын

Hi... i have video about that - How to Count Magnetic Poles of Hub Motor Without Open (Video)

@user-ik8zs5yo2t

7 ай бұрын

@@EVCustoms bro thank you very much for all the information

Fardriver with pedal assist connection?

What kind of display is that?

Will this work woth bac8000

Thank for your effort. But I have a question. Can I use Power Supply 72V 10A to test with Far-Driver instead of using Battery.

@EVCustoms

3 ай бұрын

Yes of course..

@baoho7547

3 ай бұрын

@@EVCustoms How can I lock the Wheel of motor bike (motor lock)?

@baoho7547

3 ай бұрын

@@EVCustoms Need I limiting the current of Motor and Controller

top video

@EVCustoms

9 ай бұрын

Thank you my friend! 👍😀

@Elpatronbikes448

9 ай бұрын

@@EVCustoms every one of your videos is very good ... I learned a lot from your videos ... I wish you much success in your work

@EVCustoms

9 ай бұрын

Thank you mate!

Can you show circuit diagram for test board?

Salve mi sa dire gentilmente come si fa a capire se un display è compatibile con qualsiasi centralina? Grazie

Alangkah baiknya ketika anda juga membuat video versi votol controller

Hello I have the same set up when i connect the battery to the controller im only reading 1.7v but the battery is reading 68.2v any ideas? Has the controller gone faulty??

@EVCustoms

6 ай бұрын

Hi.. your BMS is deactivated.. measure the battery voltage under load....

@samingham3077

6 ай бұрын

How do i activate it?

@EVCustoms

6 ай бұрын

@@samingham3077 You must make diagnosis on the battery... most probably you have some parallel cells undervolt or any bms cutted wire... check your battery

How to custom booting logo screen?

I can only use this controller on this display. Or I can use another controller....?

@EVCustoms

3 ай бұрын

On fardriver and Votol controllers..

Hi I'm from France Would you consider zoom meetings so we can create an international ev enthusiasts group

Здравствуйте! Где такой дисплей можно купить. Есть ссылка?

@EVCustoms

4 ай бұрын

Привет.. пока нету никаких ссылок на этот display, можно купить только через агентов

Isn't there a tiny screen option aviable ? That thing is way to big

@EVCustoms

6 ай бұрын

That's true... No yet, I will be great if this company produces more compact (smaller) screens..

hi, you're great, I always follow you. where can I buy this display?

@EVCustoms

5 ай бұрын

Thank you mate... unfortunately there is no any store out there.. you can buy it only from agents.. if you want u have one in stock first generation and 2 second generation with touch screen

Kalkarken neden zor kalkıyor, araç titriyor

stop jabber jawing and hit that chinese m365 motor with the 390a phase current that controller claims. 👍👌⚡💥🔥☠️

@EVCustoms

9 ай бұрын

This video is for learning purposes, you think i will ride this controller on 350w motor?

Why are you avoiding everyone.?? put a link for the display..

@markj.7630

6 ай бұрын

He said there's no store for the display..

@EVCustoms

6 ай бұрын

Exactly... if someone need it, i have one spare (new) email me at ev-customs@hotmail.com

@xinyu5007

6 ай бұрын

theres no store for the display ? this display is available for sell and have a 3dr generation that support car play lol

@JC-ov7ye

20 күн бұрын

I think you should be more blunt and demanding of someone who gives us lots of quality free content 😂