No longer replying to comments on this video

@ErikisOfficial

6 ай бұрын

GET BACK IN HERE and speak to these comments!

Dude you gotta rinse the gun out with gun wash/ lacquer thinner before using. The factory coats the spray guns in oil and thats what reacted with you clear

@nuckchurris3173

3 жыл бұрын

Besides that it has a lot of air pressure

I have one and it's one of the best guns I've ever used ,clear goes down slick no buffing needed using 1.3 at 26 psi.

@swc-diygarage

2 жыл бұрын

Thanks for watching

@mericmeric01200

10 ай бұрын

26 psi clear coat ? Base coat ?? Psi?? Ventilateur full open? Liquide paint full open plasse détail setup Thanks

Hi, great job. I would like to know which product and air pressure regulation would be the most correct for the devilbiss copy. Mine is T110 mouthpiece. Thank you very much and greetings from Spain.

It’s not the gun. It’s the surface your going over. Seal it and do it again. You will find a big difference. GTI pro lites like open full fan. 3 open on fluid is ok. This all depends on temp, what temp hardener and reducers. I own a half of dozen of both, fake pro lite and original pro lites. Both shut the same.

@swc-diygarage

4 жыл бұрын

Thanks for watching,.Don't forget to subscribe.

O my God, that’s to much air pressure there...🧐

To much psi running through the gun I have one and it sprays fine but at about 10-15psi

@TIAGO543211

3 жыл бұрын

15psi is TOO LOW.

I'm amazed by the number of KZread "professional" painters that still don't understand that a spray gun has 2 (two) trigger positions. When you reverse direction you only release the fluid feed (1 trigger stage), not the entire trigger.

@swc-diygarage

3 жыл бұрын

This is true. Depends on my mood. Most of the time I don't even do that.

@steveaustin1140

3 жыл бұрын

Maybe buy a spray gun and you to could be a KZread "PROFESSIONAL" painter.

hi when you paint you do any painting in that yellow tent do you ever get any dust on your painted items?

@swc-diygarage

3 жыл бұрын

I was going to but never did. I thought the yellow light coming through the canvas would be an issue.

Thank You

@swc-diygarage

3 жыл бұрын

Your welcome. Thanks for watching.

Impressed. You didn't paint your shorts black like I would.

@swc-diygarage

4 жыл бұрын

Thanks for watching. Appreciate it.

Your blasting Way too much air through - sounds like you`ve punctured a truck tire with a thick nail and pulled it out!

@swc-diygarage

4 жыл бұрын

Yes it appears to use alot of air for 20 psi.

@IQ0100

4 жыл бұрын

SW Customs . 5:28 ....... 30psi

@swc-diygarage

4 жыл бұрын

Yes 30 for clear

@latinprince896

4 жыл бұрын

SW Customs 30 psi is a lot for clear. I think the sweet spot is around 25-28

@swc-diygarage

4 жыл бұрын

@@latinprince896 Everybody has their own preference. Thanks for watching.

Sounded like too much air when you sprayed base, could be why you got the striping. Just a thought lol good stuff though

@swc-diygarage

4 жыл бұрын

Thanks for the comment. I haven't given up on it yet.,other KZreadrs say they spray like the real one. And yes 12.7 CFM at 20 PSI is alot of air.

@jesusalvarezsayula1784

4 жыл бұрын

@@swc-diygarage I've seen them say the same too, I wonder how long itll.last though , let us know how it keeps up👌🏽

I just bought one of these to paint a fleet of concrete mixers.

Thanks for the review. But from where did you buy this fake GTI and for how much?

@swc-diygarage

4 жыл бұрын

Thanks for watching. EBay for 130 Canadian. It was the best price at the time.

@2manycatsforadime

3 жыл бұрын

@@swc-diygarage yep Ebay, got to watch what you buy on there no matter what

In your opinion does the sprayit do a better job than the fake gti?

@swc-diygarage

5 жыл бұрын

For now I would say yes because the gti seemed to have problems with the base coat but the clear came out good. Check out my ski boose respray video. I spray the same base coat with the sprayit and it goes down perfect.

i got one of these for 67 bucks and im going to force it to work for me 😂

@swc-diygarage

4 жыл бұрын

Thanks for watching. Hope you have better luck then I.

@BearBudgetTurbine

3 жыл бұрын

@@swc-diygarage nope Waste of money. i bought an Iwatta, in fact 2 of them and never looked back. I use el cheapo guns for primer/sealer/polyester. All else, the W400. About 230 each, but the improvement/results are worth it to me. I was blown away after using just knock off guns or super cheap chinese products.

@swc-diygarage

3 жыл бұрын

@@BearBudgetTurbine Thanks Scott. Appreciate your return comment. Hope that other viewers take note of your experience and realize they're buying junk.

@BearBudgetTurbine

3 жыл бұрын

@@swc-diygarage trying to save money can cost u money. If you are going to paint at home more than once buy the best gun you can afford from a solid manufacturer.👍

have you ever had any dust come on to your paint items ??

@swc-diygarage

3 жыл бұрын

All the time.Very hard to control.

Holy psi

Why you twist your hand around during application and expect an even coat

@swc-diygarage

Жыл бұрын

Thanks for watching

Ok, nice test but, if I want to buy one, how I know which is original and which is the fake? Thanks in advance.

@swc-diygarage

Жыл бұрын

Buy from a dealer like spray guns direct. Anything shipped from China is fake. If the handle of the gun has a decal and not stamped on both sides is fake. Price is a dead give away.

I got the t110 air cap had 4 holes 8 all together

@swc-diygarage

3 жыл бұрын

Yes should only have 8 holes plus the 1 in the center for the fluid tip.

Reaction has nothing to do with gun, also you are not 90° to panel with 1st test

@swc-diygarage

3 жыл бұрын

Tested several times.Doesn't matter. Its junk.

I have a fake gti an it is great good painter paint with anything

@swc-diygarage

3 жыл бұрын

Thanks for watching

@oliverwoodham6685

3 жыл бұрын

Agreed, I have a fake GTI and I'm far from a good painter but I found it very easy to use it laid 2k base a treat... not great on clear but that could have been me to be honest

I love the confidence in the title.

@swc-diygarage

3 жыл бұрын

Thanks. Much appreciated

As I message some else I hope mine not paid $350.00 when first purchase now $410.00 came rap up with bubble rap wrench with seals and a cup

@swc-diygarage

3 жыл бұрын

Where did you purchase??

What cap and tip did you have ?

@swc-diygarage

7 ай бұрын

1.3 te20

@danamcintyre3565

7 ай бұрын

@@swc-diygarage I think that's the only way the sale the fakes, I've got one not crazy about it either !

You are the bad Man

@swc-diygarage

4 жыл бұрын

Thanks brother

@mariocooldude9092

Жыл бұрын

Hahahaha 🤪

honestly, it's not the gun that troubled... both fake and real will give you almost identical result, the only different is the material difference between the real and fake, the fabrication, for example the real one looks clean while the fake one maybe having like some kind of second grade material.. but the way it sprays almost identical.. you cant just make conclusion base on the way you want to use it... i have both fake and real, using it in the same technique, same material same setting, the both have the same output, only materials are different..

@swc-diygarage

2 жыл бұрын

Thanks for watching

Cross pattern to eliminate tiger strigers. It's sounds your spraying too much air I use a harbor freight it sprays cheap but fine

@swc-diygarage

4 жыл бұрын

I've never gotten stripes in any thing I've ever painted except with this gun. I think that and excessive amount of air it uses all comes down to the pour machining of the gun and air cap. Thanks for watching.

Original TE20 air cap specs. provided by Just A mechanic. Cap face 3 hole cluster .020" - Upper horn hole .060" - Lower horn hole .054" FAKE TE20 Cap face 3 hole cluster .024" - Upper horn hole .068" - Lower horn hole .062" FAKE T110 Cap face 3 hole cluster .024" - Upper horn hole .067" - Lower horn hole .059"

@jaykrom852

3 жыл бұрын

I got a fake ProLite also (Lisson branded- I just couldn't stand to have a DeVilbiss branded fake!). It is MARKED "1.3 with a TE20 and also bought an extra set of "1.2 fluid nozzel and a TE110 air cap (which it certainly is NOT even a try at a 110- looks just like the 20). WELL, the cheapie actually sprays decently and with a big even fan, BUT both fluid tips and air caps are the same, AS I did a viscosity type test comparing the time is took to flow 2 ounces (60 cm) of thinner: Both fake nozzels Flowed at the same rate that my REAL ProLite with the 1.4 fluid tip !!! The real ProLite's 1.3 took longer and the real 1.2 took a lot longer to flow out the thinner. SO, the fakes are really 1.4 fluid tips and a rough approximation of a TE20 air caps. And the fluid tips do NOT interchange with the real DeVilbiss. And as SW Customs found out, it IS a lot heavier. My only other question is what air pressure at the gun are you using? I find my guns like around only 20 psi ( 18 to 25 depending on thickness of paint.) Yours looks like you're over 28 psi (2 bar). That will give an uneven pattern. Thanks for your time and effort on the video.

@swc-diygarage

3 жыл бұрын

Was 20 for base and 30 for clear. The gun used way more air then my others set at the same pressures. After all the hit and miss problems I had with this gun I think it's the TE20 air cap doesn't seal properly. The T110 I got has a different seal in it and fits much tighter.

@LuisC202

2 жыл бұрын

@@jaykrom852 wow I just earned this as well. I bought 2 from ebay and they are both fake. Ended up getting a real one at 4x the price but it came with 2 air caps and 3 needle sizes

isn't striping just means you used not enough reducer or just your pressure was too high

@swc-diygarage

4 жыл бұрын

Those are possibilities. But have never had that problem before or after only with this gun. Did a candy paint job with with my Bellaria at 90+ F. No problem.

@petepolyakov

4 жыл бұрын

@@swc-diygarage I see. I used a few guns in the past, original, fakes, cheap ones and the similar situation would appear if I used wrong reducer (I live in FL so 90-100 is a regular situation), not enough reducer, or too high pressure (so it would half-dry before to land on the surface). I bought one today, will repaint a truck next weekend, will see if I will have same problem.

@swc-diygarage

4 жыл бұрын

Hope you have better luck then I did. Thanks for watching and the comment.

@petepolyakov

4 жыл бұрын

@@swc-diygarage will see, I'm a bit skeptical as well. thanks for sharing, it was interesting.

@cygnus1965

3 жыл бұрын

Well how did it go? Any video?

this fake gti pro bro? plesss reply🙏🏻

@swc-diygarage

5 жыл бұрын

Yes

@mohdirwan1380

5 жыл бұрын

SW Customs tq broo

To be honest AM using fake devilbiss and AM really happy with IT.first off all u havent set the gum up properly that's why u Had nad experience.

@swc-diygarage

2 жыл бұрын

Thanks for watching

Manda uma pistola boa q pago no pix.

@swc-diygarage

Жыл бұрын

Thanks for watching.

The pro not so lite.

@swc-diygarage

3 жыл бұрын

Not even close. Thanks for watching.

Sorry man, I’m not trying to be disrespectful in any way, But you can’t expect great results, when you aren’t doing things right. First off: you needed to run lacquer through that gun first to clean all the oils & grease from the factory. Second: Gun setup is crucial. Next, You HAVE to hold the gun so it is spraying evenly! I noticed you never quite tilted the gun enough to where it was perpendicular to the substrate. That is exactly the cause of the problems you had!!! A combination of Gun Setup & The fan being extremely bottom heavy, are what most likely caused the striping issue. *Let me be clear* I am not advocating for these knockoff spray guns, BUT.. I have tried a few, and they actually impressed me! I understand you are a DIY Guy, But I’ve been production & custom painting since I started at my Pops body shop when I was a teenager, and have been spraying for over 20 years now, So I know a little about what I’m talking about. Great video though!

@swc-diygarage

10 ай бұрын

Not to be disrespectful back but I've been doing body and paint since I was 16. I think I know what I'm doing. The gun is a knock off POS. Thanks the same for watching.

@tripleeathletics

10 ай бұрын

@@swc-diygarage That’s cool, But we can all learn from one another man. That’s the mindset I try to keep. I was simply saying what I saw, and I bet I other guys that spray everyday would see the same. Doing auto body is one of the best trades in the world IMO. Those of us that spray everyday have to be open minded, if we want to get better as everything changes. I made it clear that I’m not a fan of the knock-off’s! I was simply saying I have used several and was actually impressed with how they ran. Now, I know there’s many that are crap too! When I watched your video it reminded me of a video I watched a good while ago. Look up the Dura block 007 spray gun review, and there’s a guy that reviewed one in his little shop and at first when he did his paper adjustment, he commented on how heavy the bottom of the fan was, however within just a few minutes he realized it was because the tip wasn’t perpendicular, which caused it. Watch that, and you will see what Im saying. I didn’t say that to beat you up, I simply said it because it’s true. If you aren’t willing to be open minded, It’s hard to improve man. Being a body man, doesn’t make everyone a great painter. Some can & some can’t. I have several cousins that I taught growing up, and most all of them are great body techs, But a few of them can’t paint for sh*t. 😂, Hope that helps man. Take care

Do you weigh pot on that scale? Jesus do the whole world smoke weed?

@swc-diygarage

4 жыл бұрын

LOL. Great comment.Thanks for watching.

Buy cheap Buy twice

@swc-diygarage

3 жыл бұрын

Thanks for watching much appreciated

@deanbrown7643

3 жыл бұрын

@@swc-diygarage you're welcome keep up the videos 😄😄😄

Hahahabajajaja this man m not sure this is a nice paint job or bad job? Is horribly God damn it...

@swc-diygarage

4 жыл бұрын

Exactly

To buy a fake gun, is wrong in the first place. It will ruins a good brand for no reason. If they may make a "good gun", why use other's name in it? Money talks!

Sorry guy but you shouldn’t be painting you made that gun look like shit

@swc-diygarage

2 жыл бұрын

Sorry guy that gun is shit. Check about my Honda bike videos. Thanks for watching.