Finally, someone that made it easy for me to follow along.

@MarkMethods

4 жыл бұрын

Glad it helped out!

@RajVeer87156

3 жыл бұрын

@@MarkMethods great vidz man,watching from an island in the Indian Ocean

How do you not have more subscribers, this was an incredible tool for taking my engine apart, however I wish I saw part one before cause I wish I realized I could take the intake manifold off with all that jazz attached. The pain lol

Big help, thanks for this! I acquired a car with a damaged motor and also another damaged motor as spares, although the damage appears to be catastrophic to both so it was good to see you fully disassemble and know there are no shortcuts to getting the crank out :( I was hoping heads could stay on. What a shame! Thanks again.

I like how you loosen those off in a cross bolt pattern. Good workmanship

great job well done mate

Dude ik u probably forgot about this video, but i wish I could tell u how much u helped me rn

@MarkMethods

2 жыл бұрын

Glad it was helpful!

Are you going to do a follow up of the assembly of the fa20?

Forged internals install please

That’d be REALLY helpful. I just got done assembling mine. I’ve already put it in, but it’s not starting. So seeing a video that like this for the assembly would be a big help. Help me figure out where I went wrong

@MarkMethods

3 жыл бұрын

I will be building up this used FA20 shortly, did you put the crankshaft position sensor plate back in the correct orientation? It's between the crank and the flywheel.

Broo. I hope I never end up in your shoes but if I do I know I'll be referencing this video, so thank you. I guess all I'd really need to add to my toolbox for this job is an engine lift...

Really struggling with those rod bolts 😅 I find it easier to break the bolts if you pull towards yourself so you can brace the engine against your body. Especially when on an engine stand with wheels.

I was wondering if it even makes sense to change the rod bearings preventative, and if so, what else on the way would have to go just to disassemble the upper oil pan?

Great time lapse, thank you! Out of curiosity, why did you push the pistons and rods out by hand rather than by turning the crank to at least get them out as far as possible?

@MarkMethods

4 жыл бұрын

Looking at the service manual, they do mention removing the end cap then rotating the crank like you suggested. Good catch, I ended up just guiding them out by hand, probably why it was a little bit tougher to remove. I was getting excited to see if the crank could be reused and rushed, unfortunately it looks like it's too heavily damaged.

Good video! Correct me if I'm wrong but you could have knocked the wrist pins out of the rod/cylinders before taking the rods off the crank. May have been easier. At least that's how it is on EJs. 🤷‍♂

what bolt did you use for the engine stand?

What size socket did you use to take the block apart ?

What size bolts are the head bots and the bolts to take off the rods?

Where did you find the manual for the tear down? I have to take my fa20dit apart this week to do the valve seals unfortunately

What is the valve clearance at the outlet and inlet? FB20B

What size and type of socket was it for the case halfs it was a bit to fast to pause

Salut pour caler le clage est ce que les piston sont aligner ou bien j'ai problème avec le vilebrequin

Is the crank sprocket pressed on ? I ordered a short block from Subaru and haven’t received it yet.

Hey this was a little bit ago but my crank pulley hub is stuck in the crank. Any tips

Hey Mark! Do you remember what size bolt you removed at 18:14? Excuse my lack of knowledge as a novice here pleaseeee

👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿

Harbor freight sells plastic containers that you can individually put the rocker arms and buckets away

@MarkMethods

4 жыл бұрын

That's a great way to keep organized, might have to see if I can pick some up.

@JonathanLopez-zm1rv

4 жыл бұрын

Bro I was working on one of these on day and as soon as I yanked the cam carrier all the arms and buckets flew to the floor we were all like OH OOOHHHHHHH!!!!!

Did you ever have to play with the valve shims at all? And specific placement?

@MarkMethods

4 жыл бұрын

I will be leaving the shims, taking measurements, and replacing as needed to keep within specification. Highway use motors are highly unlikely to need much adjustment if any; I don't anticipate needing to replace them but will if needed.

Hi , would a valve spring recall involve changing the Conrod bearings ? If not , then would they check them as part of the job ?

@MarkMethods

3 жыл бұрын

They would remove the heads and only fix what was needed; it would be a good time to check but the extra labor hours and procedure aren't there to my knowledge.

Hey Mark I noticed in your videos you referencing something you have printed out. I'm just about to embark on disassembling my rod knock motor and your video is really taking the fear out of me but I was wondering if you could link me to what you have printed out in case it has diagrams and torque specs. Great video btw.

@MarkMethods

4 жыл бұрын

Not sure I can really link it directly without getting in trouble but here's the Google search: "ft86club demos manual" let me know if you find the repository with the factory service manual.

@MaksShap

4 жыл бұрын

@@MarkMethods found it, thanks bud

Where did you get your service manual from? For the step by step on breaking down assembling torque specs etc?

@MarkMethods

4 жыл бұрын

Google "brz service manual demos"; I don't think can link the site but there's a link in the first fa20club post, let me know if you've found what you're looking for.

What were you doing with the roller rockers when you looked at then and put then bCk. Just inspecting?

@MarkMethods

4 жыл бұрын

Taking a look to make sure metal hadn't damaged the rollers; still need to pull the cam caps to get a better look at the cams.

@Wolverine05

4 жыл бұрын

@@MarkMethods thanks mark I appreciate the reply. This video has helped me alot. Had to figure out the 12 mm 12 point socket for the block bolts you held it up to the camera but it was in fast mode lolol

@Wolverine05

4 жыл бұрын

@@MarkMethods I literally just pulled those 10 long block bolts and iam about to start malleting the block apart

The timing cover came off that easy?

@MarkMethods

4 жыл бұрын

No it didn't lol, I struggled off camera because I left a bolt in that I missed; it should come off easily once they're all removed though, once you pry a little on the cover *carefully* run a razor between the gap and it'll let loose easy.

@knucklehead9968

4 жыл бұрын

@@MarkMethods thanks Mark Meathods!

Damn a lot of sticky gaskets I see you constantly checking for bolts gonna have to keep that in mind in the future lol

@MarkMethods

3 жыл бұрын

For sure, I didn't want to start pulling or whacking away until I was certain.

Where’d you get your torque pattern for disassembly?

@MarkMethods

3 жыл бұрын

If you Google "brz service manual demos" you'll find the top ft86club post will lead to the factory manual.

Is it possible to change rod bearing without disassembly

@MarkMethods

2 жыл бұрын

I don't think so imo, it would be really tough to roll them out if not impossible.

@madmiata1887

2 жыл бұрын

You can get to #2 and #3. I had really bad rod knock on #2, I polished crank journal best I could but still saw a little damage. I put a new bearing in it anyways for fun and ran it for 10min. Started knocking after 10 min of running. The engine is out now and I am going to tear it down using this video. Hopefully my crank is ok, if not, will try to get one from subaru.

How much do you charge for a teardown and rebuild?

@MarkMethods

3 жыл бұрын

I do this work for personal projects, haven't thought about doing it on the side although that would be fun.

So would you be able to reuse cam gears on a built block if the stock motor didnt have engine failure and only had 30k on it?

@MarkMethods

4 жыл бұрын

Make sure there is no scarring on the lobes, I wouldn't be concerned using them again; that's what I'll be doing in my build. Make sure they're clean though and give everything you reuse has been cleaned and inspected extremely closely though if you're donor had a spun bearing. I've ordered a new crankshaft a week ago; discussed with a few shops/builders who said not to grind the crankshaft due to concerns of failure.

@_wrx_WHPFaDIT

4 жыл бұрын

@@MarkMethods i have a pro iag gold shop building my block everything but the cam gears are new. They said they were in amazing shape and there was no reason to get new one. But using an iag stage 3 closed deck block and stage 5 heads. Thank you for the information i will make sure that inspection and cleaning was done properly. The block they came off was still running strong i just pulled it for a built block and more power lol

@MarkMethods

4 жыл бұрын

Very cool! I'm sure it'll work out. What are your power goals and application? That sounds like some serious potential for whatever you're looking to do.

@_wrx_WHPFaDIT

4 жыл бұрын

@@MarkMethods so first go around I'm shooting for 520ish but with the fa20dit fueling becomes an issue at that point so ive upgraded what can be done to stock fueling and see if it helps then i just want to run it there for a bit make sure the build is solid. Then about a month later I'm going full level 3 Motec ECU and adding hybrid port injection. I have the wrx with the fa20dit and ill be shooting for 700+ and see what happens

@MarkMethods

4 жыл бұрын

That's a sweet build, if you've got an Instagram or something where you're posting let me know; I'd love to see where you get to. Any plans to upgrade the transmission? I have one sitting in my shed because I know the BRZ tend to blow up past 400 whp.

In part make me lost the fear o open one of those engines...

Where is this build at now? I’d like to see an updated video

@MarkMethods

4 жыл бұрын

Been stuck finding a crank; I'm going to bite the bullet this week and order a new one.

@Bizarado

4 жыл бұрын

Mark Methods I have a complete short block with super low miles if you’re interested in buying

@MarkMethods

4 жыл бұрын

Might be interested depending on location lol, did this have a spun bearing?

@Bizarado

4 жыл бұрын

Mark Methods I’m in Las Vegas, but I can ship it. It has nothing wrong with it. My buddy at the dealership got it because insurance got him an entire new engine because Carmax couldn’t figure out a solenoid issue so the insurance gave Subaru money for a new engine and it only had like 20k miles or something. Everything is in excellent condition.

@MarkMethods

4 жыл бұрын

Shoot me over how much they're looking for shipped to NJ; I'll provide some more details in email. mark@markmethods.com always appreciate leads on parts.

Are you going to do a rebuild of this motor?

@MarkMethods

3 жыл бұрын

I wanted to, had all the parts and started the process; been rethinking my approach with the kmiata K24 swap. More potential reliable power/torque and cheaper to replace motor is tough to argue. But with car prices being so elevated I may set it to stock and sell the BRZ and think about my next car. So many options.

@1atinlove

3 жыл бұрын

@@MarkMethods understood, im on backorder on everything. I was hoping to catch more content. Love your approach, and vids. Good luck on your other build.

any more of the FA20 :(((((((

@MarkMethods

4 жыл бұрын

Working on sourcing a crankshaft; probably going to need to buy a new one as every used one I've received has been damaged and these shouldn't be cut. Hopefully I'll get some more FA20 content out once this pandemic calms down.

Part 3?)

@MarkMethods

4 жыл бұрын

I really need to get down to business and order a new crankshaft; been lagging behind working from home.

how smart ya gotta be to put a pin in the engine stand so the motor doesn't keep spinning when he was trying to break head bolts loose. then using a screwdriver to pry apart the cam carriers from head then again prying the head off block. smh

A motor is not an engine.

@MarkMethods

4 жыл бұрын

Motor and engine can be used interchangeably, I'm not getting into the semantics but they are easily found if you Google "motor vs engine".

@rkratz2924

4 жыл бұрын

@@MarkMethods I know the reasons why this bastardization of the English language has happened, but maybe you should check the etymology of the word motor and maybe you might get it??? Since you are working on cars I got three words for you, Internal Combustion Engine.

@MarkMethods

4 жыл бұрын

I studied Latin for a few years, I totally get the argument; English is difficult enough already and I consider this a superfluous nuances of language. Should we write a letter to Ford Motor Company, General Motors, your local Department of Motor Vehicles, or Bavarian Motor Works and asking them to change their name?

@rkratz2924

4 жыл бұрын

@@MarkMethods because those are names that have inference to causing or imparting motion. Charlotte Motor Speedway is a track made of wiper motors, sunroof motors or power seat motors then? Obviously not, vehicles are in motion around the track.....hard face palm guy, especially since you studied Latin. Been a tech for both Ford and Toyota and never have I once seen a manual refer to an engine as a motor.......especially when dealing with hybrids. There is a difference.

@MarkMethods

4 жыл бұрын

@@rkratz2924 Multiple times I have recognized in our conversation that there is a difference between motor and engine and never once denied that, thanks for stopping by and good luck on your future projects!