EZGO TXT 295cc Robin Engine Tear Down (EH-29C)
Ойын-сауық
Step by Step Instructional video on disassembly of the very popular 295cc Two Cylinder Robin engine. This is the second video in a series where I remove, tear down, rebuild and reinstall the Robin engine. Look for those other videos to assist you with those tasks too. Also please be sure to hit that Like Buttton and Subscribe. I REALLY appreciate each and every subscriber. Leave a comment or question and I'll respond back.
Thanks again!
Here's the link to the kit I used:
www.ebay.com/itm/185003376721
Пікірлер: 42
Thank you for doing this! I’ve pulled my motor and wasn’t sure how to remove the clutch so that is a big help. Also there are so many little parts on this motor that the way you have documented your rebuild is gonna be a huge help putting it back together. My cart went out in a cloud of smoke! I feel like I broke a ring. Thanks again.
@NINEPOINTFIVEPROJECTS
3 ай бұрын
Hi thanks for watching and the comments. Glad it will be helpful for you! Let me know when you get it back together and how it runs. I think you may have already but if not please consider Subscribing and hitting the like button I would really appreciate it!
The white wire goes to the oil pressure switch, not all carts have them, but you could connect a light to is so when you lose oil pressure the light comes on. I like how you show the bolts as you pull them out, I take photos.
@NINEPOINTFIVEPROJECTS
Жыл бұрын
Good idea 💡
The hot tip on removing the driving clutch is to fill the center hole with grease and then run in a bolt. The pressure pops it off.
@NINEPOINTFIVEPROJECTS
8 ай бұрын
Hi thanks for watching and the comments. Yeah, I used oil and it worked pretty well too. You may have already but if not please consider Subscribing and hitting the like button. Thank you !
Top job and willing to have a go for sure !
@NINEPOINTFIVEPROJECTS
11 ай бұрын
Hi and thanks for watching and the comments. Yeah the whole process is not that bad. I have 2 other videos on the engine, one removing it and one rebuilding it. Check those out as well. You may have already but if not please consider subscribing and hitting the like button. Thanks again.
People bash WD-40 but it works. It wouldn’t be so huge if it didn’t. Plus I’ve seen it work myself so many times.
@NINEPOINTFIVEPROJECTS
3 ай бұрын
.
Awesome video!! Thanks
@NINEPOINTFIVEPROJECTS
3 ай бұрын
Hi thanks for watching and the comments. Glad the video was helpful for you. I think you may have already but if not please consider Subscribing and hitting the like button. I would really appreciate it! Thanks again.
Awesome video. Thanks so much!
@NINEPOINTFIVEPROJECTS
Жыл бұрын
Hi and thanks for watching and the comments. I also have a rebuilding video on the engine that may be helpful as well. Either way I appreciate you watching. Also if you haven’t done so already please consider subscribing. It would help me a lot!
@Gus_1991
Жыл бұрын
@@NINEPOINTFIVEPROJECTS already subscribed and have been watching your other video! Thanks again!!
Great Job!
@NINEPOINTFIVEPROJECTS
Жыл бұрын
Thanks John
The front aluminum engine mount has a throttle control bracket (black steel), that bracket makes it difficult to remove the engine from the cart, I put those bolts in the opposite direction when reassembling, head of the bolt now faces the front of the cart and the nuts are between the bracket and engine, with the bolts in that direction you can remove the entire throttle and governor linkage by removing 4 bolts.
@NINEPOINTFIVEPROJECTS
Жыл бұрын
Good idea!
I subed btw thanks
@NINEPOINTFIVEPROJECTS
Жыл бұрын
Thanks, I can use every sub.
So did you install sum bored over pistons or any upgrades? Im tearing into my 08 next week with the bored over kit for 60 bucks.
@NINEPOINTFIVEPROJECTS
Жыл бұрын
No I just bought the standard size kit. No upgrades. Thanks for the Sub! I really do appreciate it.
Do you know where to get a coil pack for the same engine - same as mine- txt 1996 ezgo
@NINEPOINTFIVEPROJECTS
11 ай бұрын
Hi, thanks for watching and the comments. I would think you could probably find it one on ebay? Let me know how your rebuild works out and don’t make the same mistake I did regarding the timing marks on the belt pulley. I think you may have already but if not please consider subscribing and hitting the like button.
Do you have a torque spec for the bolt that attaches the drive clutch to the crank shaft? Thanks
@NINEPOINTFIVEPROJECTS
7 ай бұрын
Hi and thanks for watching and the comments.. I'll have to look and I'm not to where I can do that at the moment. I'll get it for you as soon as possible.
@NINEPOINTFIVEPROJECTS
7 ай бұрын
Hi Pauldowns9880, Sorry for the late response and you probably already have your question answered. I do not have torque specs for the drive clutch bolt. I looked on line and didn't find the answer either. To be honest, I think I just tightened it about as tight as I could get it with a foot long ratchet. It's a large fine thread bolt and I wasn't too concerned with striping it out the way I did it. Let me know how your rebuild goes (or has gone).
I see you left a comment down below about a link to the rebuild kit in the description, but I do not see it.
@NINEPOINTFIVEPROJECTS
2 ай бұрын
You know, you're right! I just now went and fixed that! Thanks for watching and the comments. Please consider Subscribing and hitting the like button if you haven't done so already. Thanks again.
@sparklingcityservices
2 ай бұрын
@@NINEPOINTFIVEPROJECTS Subscribed! What engine oil do you use in this motor?
@NINEPOINTFIVEPROJECTS
2 ай бұрын
I used 10w30. I think I saw that listed as a requirement somewhere. You might better google and double check me on this on. Thanks for Subscribing!
Where can I buy parts for robin 295cc for ez cart
@NINEPOINTFIVEPROJECTS
9 ай бұрын
I bought mine on eBay. There is a link in the description. Thanks for watching and the comments. If you haven't done so already, please consider Subscribing and hitting the like button. I really appreciate it. Also let me know how your rebuild goes.
Onde posso encontrar motor desse pra comprar completo
@NINEPOINTFIVEPROJECTS
3 ай бұрын
no hablar
All keyways face up when timing, the dot actually is about 4 o'clock when timed correct.
@NINEPOINTFIVEPROJECTS
Жыл бұрын
Yeah that dot threw me off...I should have known better. Live and learn...
Man scrap the wd40 for soaking, get yourself some PB blast" youll thank me
@NINEPOINTFIVEPROJECTS
Жыл бұрын
Good advise!
Water, for the hydraulic pressure, much less messy!!
@NINEPOINTFIVEPROJECTS
9 ай бұрын
Hi, thanks for watching and the comments. I'm not sure water would have worked. Have you done it with water? Either way if you haven't done so already please consider Subscribing and hitting the like button. I really appreciate each and every subscriber as I continue to try and grow my channel. Thanks again!