This was really helpful! Thanks for the step by step! I will definitely be watching this again to reinstall the engine once I'm done rebuilding it.

@NINEPOINTFIVEPROJECTS

2 ай бұрын

Hi thanks for watching and the comments. You may already know it, but I have a rebuild video and an installation video as well. Maybe they can help you in those areas as well. Either way, if you haven't done so already please consider Subscribing and hitting the Like button. I would really appreciate that!

I'm just getting ready to do this to my 95 Medalist. Thanks so much for your help!

@NINEPOINTFIVEPROJECTS

11 ай бұрын

Hi, thanks for watching and the comments. I'm happy that the video may help you out a little. Mine is still doing well. Just be careful not to use the wrong mark on the timing pulley as I did first time. I knew better than to assume. Either way, I think you may have already, but if not please consider subscribing and hitting the like button. Thanks and good luck.

Nice, well done, I like how you speed through the removal of bolts and nuts, now I need to do mine.

@NINEPOINTFIVEPROJECTS

Жыл бұрын

Hi John, thanks for watching and the kind comments. I'm pretty new on KZread and still learning how to improve my videos and comments like yours is great feedback for me. If you haven't done so already please consider subscribing and hitting the like button. I would REALLY appreciate it! Every subscription helps me a lot!

@NINEPOINTFIVEPROJECTS

Жыл бұрын

John, I also meant to let you know I also have a video of the rebuild that may help you as well. Thanks

@johnisbell9220

Жыл бұрын

@@NINEPOINTFIVEPROJECTS I'm in the process of rebuilding my engine, waiting on the kit of parts, there seems to be a vast difference in parts, I bought some valves that look bad, the kits are the way to go, buying piece meal is expensive, still with all I have bought it's cheaper that shipping it off and paying someone else.

I went through this in June. Wasn't bad. I'm not as strong as you. I used my engine hoist to lift out and go in.

@NINEPOINTFIVEPROJECTS

8 ай бұрын

Hi thanks for watching and the comments. Engine hoist is definitely a better way to do it for sure!! I not very strong either. Either way, I think you may have already but if not please consider Subscribing and hitting the like button. Thank you!

Getting it out was not a problem. It’s getting it back in. Trying to get all 8 boots to line up was a nightmare.

@NINEPOINTFIVEPROJECTS

Жыл бұрын

Hi and thanks for watching and the comments. Mine wasn't too bad. Did you happen to see my removal video. That might have helped you some. Either way thanks again and if you haven't done so already please consider subscribing and hitting the like button. I appreciate each and every Subscriber.

very good video very Thorough with everything. i have been researching for months now. the only thing is what rebuild KIT or parts do i go with. who makes the good parts is the ?

@NINEPOINTFIVEPROJECTS

Жыл бұрын

Hi KTECH, Thanks for watching and the comments. The kit that I used seemed to be good to me. It was complete and all parts were there. If you haven't done so already please consider subscribing and hitting the like button. As I try to build my channel, each sub means a lot to me and I'd really appreciate it!

I really enjoyed your video very informative but I have noticed no one replaces the bearings. What r your thoughts about this. I am about to rebuild a 95 medalist ezgo

@NINEPOINTFIVEPROJECTS

10 ай бұрын

Thanks for watching and the comments. I think that if the bearings are smooth and no slack in them, keep using them. Thanks again.

Wheres the best place to get parts for these?

@NINEPOINTFIVEPROJECTS

Ай бұрын

Hi thanks for watching and the comments. I got the rebuild kit from eBay and a carburetor from Amazon. Either way I think you may have already but if not please consider Subscribing and hitting the like button. I would really appreciate it!

That damn exsaust is a mother!!"

@NINEPOINTFIVEPROJECTS

Жыл бұрын

I was actually shocked how easy mine was to get off. I was sweating the bolts breaking, but they came right out. I also saw your comment about PB Blaster. Good advise there. Thanks again and let me know how your rebuild goes.