Thank you very much for your video, i'm just an lathe-hobbist ( from 2006 ) and also use inserts NC3030 as you showed in the video; much of the difference relies on type of steel to be cutted ... "common steel" ( for construction ) is the worst, to my sight of see, better i get with "silver steel". I also use my tool upside down, and opposit direction for the spin ... so i learned parting from u-tube, after so many ... "cracks" ... Operating so, the chips easily fall down ... I hightly do appreciate your style of videos, no music, no words ( often unintellegible cause different languages ) ... you just SHOW WHAT IS IT, very clear. With some indication of your hand and fingers, one can understand if a tool is ok for that work or not ... as in this video ... And finally your silent suggestions to use goggles for eye protection ... very professional ... My best greatings from Italy ... were are you instead from ?

@CoolIdeasDIY-qv1nz

Ай бұрын

Grazie e benvenuto nel mio canale!

Great video, thanks for the comparison.

@CoolIdeasDIY-qv1nz

Ай бұрын

Thanks, bro.

Good!👍👍👍

@CoolIdeasDIY-qv1nz

Ай бұрын

Thank you very much!

👍sobran las palabras👍

@CoolIdeasDIY-qv1nz

Ай бұрын

Gracias y bienvenido a mi canal.

Thank you again for demonstrating so many types! It is great to have that knowledge so we can easily sort through and pick the right inserts for us!

@CoolIdeasDIY-qv1nz

Ай бұрын

👍🤝🙏

You can sure tell the difference, thanks for the comparison 😊 !

@CoolIdeasDIY-qv1nz

Ай бұрын

Thank you and welcome.

Nice test ! Thanks, bro !

@CoolIdeasDIY-qv1nz

Ай бұрын

Thank you and welcome.

I encountered this problem and it was solved in the same way. You seem to be brilliant

@CoolIdeasDIY-qv1nz

Ай бұрын

🙏

You are doing a wonderful job

@CoolIdeasDIY-qv1nz

Ай бұрын

👍🤝🙏

Every schooled tradesman knows about these. What material your using depends on type and speed and feed are given by tip manufacturer.

I didn't notice you use any cutting fluid. Is it unnecessary with carbide?

@CoolIdeasDIY-qv1nz

Ай бұрын

I rarely use cutting fluid when I make videos to clearly show the whole metalworking process! Thanks my friend and welcome!

Thanks for the comparison. Were they about the same price, or was one cheaper or more expensive than the rest?

@CoolIdeasDIY-qv1nz

Ай бұрын

They are all about the same price, but the metal cutting quality is different, the last plate is the best as you can see from the shavings! Thank you and welcome!

❤❤❤

👍👍👍

@CoolIdeasDIY-qv1nz

Ай бұрын

Thank you very much my friend.

Good video❤❤❤

@CoolIdeasDIY-qv1nz

Ай бұрын

Thanks bro!

Estes insertos trabalham melhor com fluido de corte e não deve existir nenhuma vibração. O melhor resultado foi o último corte porque é mais próximo da fixação da máquina e teve menor vibração. A ferramenta também pode ser montada invertida (de cabeça para baixo), reduz a vibração de possível folga no eixo principal da máquina e também facilita a saída de cavacos. 😊👍

@CoolIdeasDIY-qv1nz

Ай бұрын

Concordo consigo, mas o último prato corta melhor, vê-se nas batatas fritas! Bem-vindo!

Gostei, sem enrolação e sem se quer uma palavra e de uma clareza sólida.

@CoolIdeasDIY-qv1nz

Ай бұрын

🙏🙏🙏

最后一种最锋利！

I've seen a few parting videos but never a side by side comparison of the inserts. I've only recently had luck with parting since I made my own tool holder similar to yours. Previously it was the rocker/lantern style. It's a lathe at work and they won't buy anything for it. It's a welding shop.

@CoolIdeasDIY-qv1nz

Ай бұрын

Welcome my friend.

Nie za duże te obroty ja daje na 280

@inkoguto69

Ай бұрын

te płytki wolą raczej wyższe obroty z tego co słyszałem ja daję 450 a nawet ok 700 zależy co przecinam, ale robię to bardzo rzadko ;)

Hast du keine Stimme?

very good

@CoolIdeasDIY-qv1nz

Ай бұрын

Thank you, my friend.

❤❤❤

@CoolIdeasDIY-qv1nz

Ай бұрын

🤝🙏👍