EASY PRIMER BULB FIX FOR PUSH LAWN MOWER THAT DOES NOT START EXCEPT WITH STARTING FLUID DIY
Тәжірибелік нұсқаулар және стиль
Your push lawn mower only starts when you spray fuel, carburetor cleaner or brake cleaner into your carburetor. Then it runs fine.
This short, easy DIY video will show you how to diagnose it and the most common reason your primer bulb doesn't work.
At one point in the video I said vertical and meant to say horizontal.
CLICK THIS LINK FOR THE 2 STROKE PURGE / PRIMER VIDEO
• Simple Trick For Corre...
CLICK THIS LINK TO REPAIR / REBUILD PLASTIC CARBURETOR FOR FREE VIDEO
• Plastic Carburetor, Re...
CLICK THIS LINK FOR OUR STORE TO GET YOUR TSHIRTS HOODIES AND MORE !
my-store-cf5bc2.creator-sprin...
THE LINK TO OUR CHANNEL TO SHARE WITH YOUR FRIENDS
UCA9GlAGvSMsoXBPR77JTTJQ
Edited by YouCut:youcutapp.page.link/BestEditor
EASY PRIMER BULB FIX FOR PUSH MOWER THAT DOES NOT START EXCEPT WITH STARTING FLUID
#smallenginerepair
#primer
#carburetor
@restore
Пікірлер: 114
Click this link to visit our store to get your T shirts, Hoodies and much more my-store-cf5bc2.creator-spring.com
If you look down in the hole after you remove the primer bulb, you will see a screen that is removable. I have had those screens stopped up with dirt. Also, the reason that the primer doesn't work, is that the hole in the gasket is not lined up with the carb hole. Put the cover on and leave slightly loose. Get canned air with a straw or turn your compressor pressure very low. Blow air into the hole on the front of the primer bulb while moving the primer bracket. Once the two holes are lined up, you will see gas, tighten the bolts down. I have never had to install 2 gaskets or replace a bracket. It is almost always that the 2 holes are not aligned. For ease, I keep a can of canned air in my toolbox just for this reason. And yes, the whle can also be clogged like you said in the video.
This is great stuff, my brother. Keep it up.
I found out if you take a can of carb cleaner with a straw and stick it in the hole on the primer bulb and spray some in there, it might work. It fixed my issue lol, maybe it will work with someone else too
This helped me out to running condition 1st pull start for a friend of a friend who is very appreciative of you and your channel
Thanks for posting the video! I had cleaned my carburetor, put everything back together, and had no priming. That little channel was plugged with gunk. Easy fix!
Been pulling my hair out about this issue. Thank you for the quick fix! Member for life.
You have the best videos on KZread.
Thank you for this video. Very informative. ❤
Thanks for the video. I have to push the red primer bulb about 8 x then my Toro mower starts . It used to work after just 3 pushes.I will try this .
Raley😊you just blew my mind, thank you
Good video...thank you for posting this!
Looked it up, the primer removal tool is $55 and the insertion tool is $37, that $3 socket modification tool sounds like a great idea brother. 👍👊 Nice video T-Bone, Happy New Year to you and Mrs Bone. 🙂🎉
@RaleysSmallEngines
Жыл бұрын
Yes I knew they were pretty expensive, just didn't know exactly how much. Happy New Year brother.
@Big_Johns
Жыл бұрын
Too rich for me, I’ll be modifying a socket for sure. Thanks and Happy New Year to you and Mrs T-Bone too. 🙂👍🏼
I like the tips I have some primer bases that are warped and will try those fixes to see if they help our my situation when I get to them . Good video t-bone
Great video and even better tip on the how to make the modified tool for replacing the bulb! Thank you and Happy New Year to you and the Mrs.
@RaleysSmallEngines
Жыл бұрын
Thank you. Happy New Year
Very good ,thanks
Ty so very much! With this videos help, I (not mechanically inclined at all) have fixed my mower. Again, ty.
@Mrs.T-bone
2 ай бұрын
So glad to help.
THIS GUY KNOWS HIS STUFF THANK YOU SOOO MUCH! Chinazon, haven't heard that before, nice.
@RaleysSmallEngines
Жыл бұрын
Wow, thank you
good job helped alot
This was an informative video for those who might have this problem great tip thanks for sharing. Take care and have a Happy New Year.
@RaleysSmallEngines
Жыл бұрын
Thanks, you too!
Thanks for the tip!
@RaleysSmallEngines
Жыл бұрын
You bet. Happy New Year.
Ooo i like that intro clip! @ 29 seconds
Really good information T Bone, i know a lot of people have trouble with type of primer thank you Happy new year 🎉🎉🎉
@RaleysSmallEngines
Жыл бұрын
Happy new year! Thanks for watching.
Darn tootin good video brother
The socket hack is a good one have to try it 👍 Happy New Year 🎇
@RaleysSmallEngines
Жыл бұрын
Heck Yeah. Happy New Year
heat gun unwarping priming bulb cover worked for me. Prior gasket has broken into pieces likely aiding in the warpage. Pretty easy to diagnose with the cover mounted and pressing bulb with no fuel coming out of the brass tube (Need to confirm bulb is producing air pressure with soak bubble test first)
New subscriber, this helped alot cheers dude
@RaleysSmallEngines
Жыл бұрын
Great!! Thank you
Great video
@RaleysSmallEngines
5 ай бұрын
Thank you
Just came across your video.. very informative.. I replaced the carb on my john deere ja62 and ran like a champ but wasn't priming.. haven't tried your glue gun technique yet but I was able to get it to prime by using my hand to push against the housing and put a little extra on the bolts and wallah its priming.. it might be a temporary fix and if it is I will heat it up and try your technique.. thank you for the video and just subscribed.. and by the way this is a horrible design😅
Thanks I was wondering how to change the primer bulb
ME GUSTO COMO SE PUEDE APRENDER DE OTRAS PERSONAS QUE TIENEN BUENA INTENCION DE AYUDAR......MUCHAS GRACIAS POR SUS VIDEOS ......MUY BIEN EXPLICADO
Good information mate
@RaleysSmallEngines
Жыл бұрын
Glad you liked it. Thanks Mick
I used a cheap set of pliers and welded welding 1/8 rods to it and bent them to fit the release points Works, $3.00
@RaleysSmallEngines
Жыл бұрын
Awesome idea
happy new year
@RaleysSmallEngines
Жыл бұрын
Happy new year
I love this information brother. I am going to Chinazon right now to order me a Mr. Heat gun.....lol Great video Sir!
@RaleysSmallEngines
Жыл бұрын
Lol Heck Yeah or just go steal your wife's hair dryer.... She won't mind LMAO Oh share pictures of the bruising when she throws it at you LOL
Another great video sharing the knowledge,,, Happy new year T-Bone and Mrs T ❤️
@RaleysSmallEngines
Жыл бұрын
Thank you. Happy New Year
Happy New Year Mr and Mrs T-Bone 🎉
@RaleysSmallEngines
Жыл бұрын
Happy New Year my friend.
On my 6.5 HP Briggs engine and aluminum carb, the bowl gasket was worn, bleeding air pressure needed to push gas into the tiny venturi. If Raley’s method does not make a squirt into the throat, consider replacing the bowl gasket.
Great show, the primer plastic vain you put soap in to see if it's working, does that lead to a jet hole on the carberetor at the end of the vain or valley, because mine doesn't so its going nowhere, what should it be doing please with the connection to the carb please
Good need to know information right here folks... y'all pay attention T-Bone dropping years of experience and knowledge on ya.... HEY MRS. T-BONE 👋
@RaleysSmallEngines
Жыл бұрын
Thanks brother. Mrs T says hello
Happy New Year Be safe and happy 😆
@RaleysSmallEngines
Жыл бұрын
Happy New Year
A friend was "Working" on his mower and then it wouldn't start. He didn't line up the hole in the gasket with the carb "tube". He asked me how he was supposed to "Know" that those need to be lined up... I had no words for him...
Great description of the issue and fix. Been a sub for a while and started making a similar channel trying to share any knowledge I have as well. Any advice you're willing to share for a newbie? Keep up the great work T-bone!
@RaleysSmallEngines
Жыл бұрын
Awesome, thank you! Advice for KZread? Well I have no idea what I'm doing, just winging it the best I can. Just keep putting out content, someone will watch it my friend.
@RayofallTrades
Жыл бұрын
@@RaleysSmallEngines thank you, will try that
awesome video TBone! hey aint you supposed to be on vacation?
@RaleysSmallEngines
Жыл бұрын
Thank you. Yes we were, but had fun doing the video. Happy New Year !
I have a 2008 toro recycler which I replaced the carb with the Chinese knock off. Starts on first pull, however if I shut off for more than 5 mins it won't start. Starts hot or cold , but not warm. Any ideas, a leaking cover gasket might be it? Or is there a choke thats messed up. No primer bulb its a toro 20066. It pulls easy, I heard there is a compression release, but cylinder wear is my concern. Advice?
👍🏾
Would a bad float bowl seal prevent priming?
Thank you for the video
@RaleysSmallEngines
Жыл бұрын
You are welcome
Was that primer bulb off the new mowers they are making. I have one of those newer pieces of crap mowers. Plastic carburetor, why are they doing this?
@dkupy100
Жыл бұрын
$$$
@RaleysSmallEngines
Жыл бұрын
These are very common, been around for years now.
I've had several Tecumseh. The plastic housing gets hot and warps. They can get pretty bad.
I use piece of 3/4 conduit for buld installation
@RaleysSmallEngines
Жыл бұрын
Awesome great idea
👍👍👍 Wishing a happy healthy and prosperous New Year to you and your family.
@RaleysSmallEngines
Жыл бұрын
Thank you, Happy New Year to you and your family also.
👍
Happy New Year! Nobody wants to revisit last year, but you might want to check out my "Holiday Show & Giveaway Winner" video from a week or so ago...
@RaleysSmallEngines
Жыл бұрын
Happy New Year Jack. Thanks a bunch my friend. Just now catching up on KZread because we have been on vacation.
I was pushing mine had zero action and no start, found clogged jet on briggs n stratton 300 model
I do like you
I have the same model. On the fuel inlet side of the carb there is a smaller white nipple. Where does that attach?
@RaleysSmallEngines
10 ай бұрын
It doesn't hook up to anything. Thanks for watching and commenting my friend
I've bought several over the years from Amazon over the years and 9 x's out of 10 they are warped. lol
Chinazon ...Fleebay. 😆 🤣 😂
My mower will start for a second on starting fuid but then stops. I put new gaskets, primer ball, cleaned and blew out the carb passages. No change, still will not run except to start on fluid but then dies. Briggs motor different carb that yours.
@RANS87IROCZ
2 ай бұрын
Clogged jet, Just fixed mine and it's #1 issue for them models
@RANS87IROCZ
2 ай бұрын
Even if different model most carbs have same jet set up
I tried all of this to the point of buying a new base and primer bulb. Still not getting gas to the carb. Starts and runs fine with a little squirt of gas in the carb . What else can I try? Thanks!
@RaleysSmallEngines
Ай бұрын
Sometimes I use 2 gaskets and soak them in oil, then wipe them off b4 installing.
"Slip it on my little tool"; that could be taken the wrong way!😂😂😂 I use an 18mm socket with no grinding.
Great thx man really appreciate it
@bob1519
Жыл бұрын
You have a way of explaining things - it’s a gift brother keep up great work thx again
@RaleysSmallEngines
Жыл бұрын
Wow, thanks brother
Hey that little hole in the carburetor I put gas in it don't come out the tube in the 3
Any chance of free stickers plz. Your fixing Lawnmowers, helps me alot, when im fixing them.
@RaleysSmallEngines
Ай бұрын
Email me your address to raleytrans@gmail.com and I will get you some in the mail my friend.
@derekgraham1677
Ай бұрын
@@RaleysSmallEngines Derek Graham 18 church hill gardens, dromara, dromore, co down. Bt252NB. Northern Ireland. Thanks Derek
The fuel line coming off the primer is missing I can't seem to find where to run it to fix the problem starts fine while putting fuel in carb until it runs out of fuel
@kendostick1635
2 ай бұрын
Motor is a 2015 brigs 300e have a 450e with the same issue both set since new used only a few times guessing fuel lines rotted trying to get one going for my brother in law
Government crap they need to make them with choke cables again
primer bulbs suck npt blow if blowing hooked up wrong
According to KZread, my B&S mower engine is the only one in the world that has no primer bulb.
You are not cheap, Mr
View 2 lol
Chinazon or Fleebay 😂😂😂😅
happy new year
@RaleysSmallEngines
Жыл бұрын
Happy new year
happy new year
@RaleysSmallEngines
Жыл бұрын
Happy new year