I feel like someone got a great deal for $2,500. I was fully expecting this to go over $3,500. Very satisfying video to watch - good stuff

@charliefarms1

2 ай бұрын

Thank you!

@PumpkinDog33

2 ай бұрын

I think they knew what they were getting. $1500 trailer with a $500 facelift and they didn't have to put the work into it.

@RealEstateRehab

2 ай бұрын

Yea I can't even find clapped out 16ft landscape trailers for $2,500 around me....

@FWACATA

2 ай бұрын

SAME!

@claire001savefile5

2 ай бұрын

I found a couple from 900 - 1500 might get into flipping these tbh

For future repairs; May I suggest you place a jack on the floor then a upright log on top of floor to gain extension and use that as leverage then arching the board into place. That way you lower the jack and never have to pound out the additional short pieces of stud. It will automatically be lowered and you out of harm's way. You'll save your back and be a lot safer.

@charliefarms1

5 ай бұрын

That’s really smart! Thanks for the tip. Definitely will do that next time

@Freddy-bx6sf

2 ай бұрын

For clarification your recommendation is: “Bent” board Upright Log Jack Earth And then just lowering the jack?

@RAJsWork

2 ай бұрын

@@Freddy-bx6sf Correct, if the earth is just dirt, rocks, gravel then I suggest placing a flat sheet of wood under floor jack for stability & to avoid floor jack sinking in ground.

@Freddy-bx6sf

2 ай бұрын

@@RAJsWork got it, thank you!

@fpsfrankthetank7074

2 ай бұрын

Great result! I would suggest cutting the metal and bending it out of the way that way you don't have to bend the board at all. Then just bend it back and weld it once the board is in place.

This is what honest work looks like. Showcasing costs and labor at the end tops it off.

@wing3737

5 ай бұрын

Lip stick on a pig just saying.

@mickeysuede2219

5 ай бұрын

@@wing3737 Loll that's true but I'm sure the buyer was aware of the damages when purchasing. Those car haulers can cost 5-10K new.

@HelperBot5000_

3 ай бұрын

Painted over the rust, not exactly what I'd call honest work. The rest of it was pretty good work tho. Should have sanded it all the rust out when he was stripping the boards.

@moistcu

3 ай бұрын

@@wing3737sold for $2500 obviously there’s something wrong with the trailer if it’s that cheap

@charliefarms1

3 ай бұрын

Nah brother nothing was wrong with it. That’s what they go for around here and I was trying to move it quick. Probably would have sold as high as 2900-3000 if I wanted to wait.

Someone get this man a sawsall.

@joerolex2705

Ай бұрын

that boy pulled out the chainsaw on us haha. great video

Well worth $2,500 for a steal. I have been hunting for s trailer for a while now and one of this condition would be "cheap" if listed for $3,500. Great work! Never undervalue your skills and labor. Thanks for the video!

Working a ~$20/hr restaurant job in southern california. This kind of do-it-yourself moneymaking work is inspiring. I can't wait to be able to get my own place somewhere out of suburbia to even just have the opportunity to work for myself doing things like this.

@MrSagerific95

Ай бұрын

We moved from the inland empire (upland) to Connecticut during Covid to start a homestead. We bought a busted house on a big chunk of land, now we have goats for dairy and chickens for eggs, we grow vegetables every year. The move and the first year was definitely a struggle, at times we were scared we made the wrong choice, but that’s what “change” does to you I suppose. We’ve never been happier… plan for it, start researching what you want to get into, and as soon as the opportunity presents itself go for it!

@bananaboy444

Ай бұрын

@@MrSagerific95 that sounds like exactly what i want to do :) it feels great to hear about others pulling it off, im happy for you. I'll make it happen myself soon

Really nice job. For a second there I read the breakdown and thought you only made $43 profit. That’s a lot of work for $43. But then I finally read it right. $42 an hour is at bad. Especially since your outside, no boss, work when you want and no one tormenting you. Good job man!

@billythygoat

2 ай бұрын

I mean that doesn't count his own tools, his truck getting it, time buying or selling it, prep work, the spot it needs take on the property and general tool wear and tear.

If you do this pretty often might want to invest in a airless sprayer. You'll get the job done with the same quality, but you'll save money on paint if you buy 5 gallons at a time. Cleaning the machine takes about 15 min. I'm a painter so I'm inclined to this thinking. Solid job brother.

@charliefarms1

3 ай бұрын

Just bought one! Literally painted a trailer a couple days ago with it. Really worked awesome and saved a bunch of money on paint. A video is coming soon for that one too. Still getting used to everything

The cost breakdown at the end was excellent! Thanks for including that

@try44

3 ай бұрын

He didn't include taxes which would at least be $175. Dropping his hourly rate down to $30. And with video evidence online now you better believe the IRS will take note of it. It's far easier for them to audit people who can't afford lawyers than people who can afford lawyers. Remember that.

@charliefarms1

3 ай бұрын

@try44 I pay my taxes, relax lol

@try44

3 ай бұрын

@@charliefarms1 okay? I never claimed you didn't pay taxes. I said you did not Include it in your cost/profit breakdown. So why exactly are you telling me to relax?

@charliefarms1

3 ай бұрын

@@try44 because you’re freaking out about taxes lol. It will be okay. I handle my finances and I’m sure other people understand that they would have to manage theirs if they did the same.

@try44

3 ай бұрын

@@charliefarms1 noting a cost that was not mentioned in the video is freaking out? Furthermore if you want to claim I'm freaking out about something it's overwhelmingly obvious that it would be the length the government will go to gather a small amount of money from citizens. In case you need another reminder, I never mentioned your finances or if you pay taxes or not. My comment is just as truthful and relevant now that you've shared that you pay your taxes. How you connected my comment to you paying your taxes is still a mystery to me.

Oh she's a beaut Clark! Good job man looking forward for more flips. 👍

@charliefarms1

4 ай бұрын

Thanks! More coming for sure

@Blasterer

4 ай бұрын

@@charliefarms1I’ve been looking for a side hobby to make extra cash and this video shows up. Thanks for the inspiration, keep up the work. That trailer looks amazing

I do this for a living. Taking old trailers and making them new again. I used to be able to find them dirt cheap and rebuild them and make a profit. Now days you cant make a profit on them. People want too much money for a piece of junk, and the prices for parts went up. Hard to make a profit. I stay busy rebuilding others trailers for them. Its not as easy as one would think.

One more way to cut the cost a little is to use old motor oil for the wood deck sealer. Thin it a little with paint thinner and roll it on heavy (or spray with a pump sprayer with a fence staining tip). It looks good, lasts a long time, and is virtually free. The smell is strong at first but fades quickly with sun and time.

@thetrudrewwilson

5 ай бұрын

Can attest to this. Works great

@crodoutdoors

4 ай бұрын

We use diesel fuel to thin it out.

@tywarren4704

4 ай бұрын

Yep. Used motor oil with diesel fuel is excellent for coating wood.

Please more! I have no use for trailers, but this is so nice to watch. Keep it up man!

@charliefarms1

5 ай бұрын

Thanks!! I really appreciate it. More to come

@RAJsWork

5 ай бұрын

Same here, I couldn't agree more!

@floatingaxtechnologies2656

3 ай бұрын

Could you imagine telling a TV executive 20 years ago you were going to have millions of people watching a dude restoring a trailer? KZread is awesome 😂

@charliefarms1

3 ай бұрын

@@floatingaxtechnologies2656 that made me laugh out loud haha thanks!

I’m liking these trailer build series. Quick and to the point.

Great job sir. I agree with some of the others. I expected this trailer to sell for more. Adding the red and white reflective stickers would add a nice touch to your already stellar work. Thanks for the video.

Appreciate both your trailer work and your video edit skills! Both are great!!

Can we talk about the semi rolling down the highway backwards in the background at about 8:35? lol! Seriously though, good job!

Nice job on the trailer. I agree a sprayer and bulk paint would save money, if you are going to do this regularly. Enjoyed the video.

Nice to see these videos keep coming, keep it up man! Love the effort that has gone into the editing and all the price breakdowns

I could watch this all day long! Great video!

Very nice transformation! If you do enough of these, I feel like you could save a little money or at least have a better product for the same money if you got a harbor freight HVLP gun and sprayed with a 2k high build primer that you can buy by the gallon on the internet and then run to john deere and get some blitz black implement paint. Just a thought, and it'd save your fingertips. Keep the videos coming!

@charliefarms1

6 ай бұрын

Thanks! Yeah I plan on getting one in the spring. Had a hard time with the first one I bought so I have been hesitant to try it again lol

@Art-uz3fk

5 ай бұрын

​@@charliefarms1rattle cans are less hassle tho. The Rust-Oleum pro grade cans go a long way too.

Used to do this for a living, new custom trailers and rebuilds , lots of money, hard work, but you get to take pride in a quality finished product, except when a bum pays you with a bad check.

I love the cost breakdown and profit breakdown at the end. Good to know that it wouldn't be worth my time if I was doing it to make money, but I'm in the process of doing this with a trailer I own, so it was fun to watch 🤘🏼

I'd mount a battery and winch on that and keep it! Great job!!

DUDE! Good work! Loved how cut and dry you did it, and the plank trick is awesome!

@charliefarms1

2 ай бұрын

Thanks!!

What I did to make it easier to replace the boards is just cut out a notch, put the boards in and slight them over, and then tack weld the piece that was cut out. Can be recut and rewelded for future board replacements

Wow! What a big difference, keep up the good work!!

@charliefarms1

6 ай бұрын

Thank you!

one thing that is important with stick welding is to wear good gloves at least for your support hand because that hand will get exposed to alot more radiation(heat, mostly). and the tacking method you did works fine for something like sheet metal but in the future if you ever did this in a shop it can be alot easier to tig weld the sheet metal on a really low amperage maybe 30-35 or so. normally tacking would be no bueno but sheet metal has bit different of rules because it isnt weight bearing. nice video btw - nate, a welder mostly

@charliefarms1

4 ай бұрын

Been wanting to get a wire welder. I used one back in college and I could weld really well with it. Any recommendations on an affordable wire welder that can do this type of work? It’s been over 7 years since I’ve used one though

@natenate2280

4 ай бұрын

@@charliefarms1 tons of options but to be honest when it comes to mig and tig equipment it's mostly a "you get what you paid for" situation. for tig I like Miller's for mig and stick/fluxcore I like lincoln's but ive used both and just feels like miller's are constantly needing maintenence in comparison. There are so many types of welders out there I would just say search based on your budget's price point. Also it depends alot on the situation. Gasless fluxcore ran off of a generator can be real cheap but you need to handle and store that flux wire carefully. It doesnt need the carbon dioxide gas that DS fluxcore does (but can sometimes be added to the machine with a hose I believe) and with a gasless fluxcore wire you can weld outdoors with out the need for a gas tank. Personally im gonna be building a mobile rig soon with an inverter generator from Harbor Freight called the Predator 9500 with a Titanium 225 stick welder (also from HF) to start out my side hussle after work along with all the common hand and power tools.

@natenate2280

4 ай бұрын

@@charliefarms1 but for this kind of sheet metal work if you cant get an oxy welding setup id recommend getting a gasless fluxcore welder than can run 1/16" fluxcore wire and a set of copper backing pieces to absorb some of the heat when you are welding very thin metals and large gaps or both

That was bloody great to watch

Hell yeah, man. Good job!

Don’t feel too bad about the welds on the fenders… welding thin steel to much thicker steel is always hard. Ends up being too hot for the thin metal but too cold for the thick.

Nice job man!

Great work

Great work. Easy to understand and no bs straight to the work. Keep up the work. Def learning alot and staring my own thing soon.

I miss my old Ford Ranger 4x4 😢 I sold it and bought a F150 for better tow capacity (i do landscaping)... Now im always paying to fix this big piece of crap at the garage.

Love this channel

I'd say that turned out pretty nice.

Just found your channel and you have got yourself a new subscriber mate! :) great videos and great work my friend, please keep it up :)

Nice side hustle

None too shabby! Well, sorta shabby, but no longer beat to shit. Nice flip!

Great video. Around here in TX people want 2500.00 for the way the trailer was in the beginning.

@charliefarms1

3 ай бұрын

Thanks! I know I’ve been thinking I should take the finished trailer to a bigger city and get more for it

Strongly encourage you to charge more for this level of quality, the profit should double the initial cost, so you can start the next project without having to dip into your savings.

@charliefarms1

8 күн бұрын

Thanks I appreciate that. Will be doing that in the future

Great job, I definitely think you could sell this for much more!

Fantastic job wow. I took lots of notes lol. Hard work I can see. I am surprised you didn’t sell it for more, maybe your area and more details but I also don’t know much about trailer prices lol. Either way you did amazing and I hope others can learn from you.

@charliefarms1

4 ай бұрын

Thanks! I appreciate it! Yeah in my area most people won’t pay more than 3k for something unless they can make payments. It works for me and I enjoy the work

The typical “garage kept it’s whole life” trailer 😂 zero rust

Lmao the pick axe made me laugh

Nice job

Awesome. Give us some tire shine on the next one. Possibly a little more negotiating on both sides and that’s a real good gig

Those truck drivers drive backwards in Kentucky! Thats almost more impressive as this trailer flip!

@charliefarms1

4 ай бұрын

Hahahah 😂 didn’t think anyone would notice

Should have sold it for more. New those go for 6k depending on axles.

Looks great! hopefully you cleaned the underside as well.

That is not easy money, you put some work into it, turned out great!

Man, you ought to get one of those handles for spray cans. Save your fingers. Great side hussle though .

good video, I'd do this in a heartbeat but where I live trailers in the rough shape it was in when you got it are still going from $3k-$4500 lol

@ashleighelizabeth5916

2 ай бұрын

Wow, I may have stumbled into the one category of things in my area that are not insanely overpriced because I thought $1600 was overpaying for it in that condition and was surprised he only got $2500 on the back end if he had to pay that amount to start.

Lol the pickaxe took me out.

Being your own boss: priceless

Coolest part of this video was you peeling the plastic off the lights

Good job

@suzannasymonds8982

Ай бұрын

Wuushdyh5dgisnhmkhjjjopomjdhddhchcchcnd8 I ehuwheudihewu2jppo m m

Remember everyone, a grinder and paint makes you the Welder you ain't.

Might i suggest for quicker and safer work, to cut the metal lip section, bend out of place, install board with ease, then bend lip back, tack and smooth. 👍

Have you ever used tractor implement paint? I buy fix and flip trailers down in FL, I usually use a wire brush on a grinder to knock off any surface rust then use the Majic or Rust-Oleum High gloss black Implement paint. The paint is like tar but looks amazing when its done and lasts for about 5-7 years before it needs to be repainted.

How many cans of primer and paint? And is the paint gloss or semi gloss? Also I could suggest adding the reflective tape, i just flipped my first trailer and it adds a nice pop to the sides

Would look nicer with reflective tape on the sides. Nice flip.

Nice!

never even considered flipping a trailer. ty

Nice!!

I think the trailer was slightly overpaid since it was in pretty rough shape but overall great work and repairs!

Great video i just picked up a 18ft trailer. I'd like to do what you did. What kind of welding product you used and what brand degreser?

Another suggestion: Dulux has a good stain called “Professional Wood Finishes 100% Oil”. Pick a dark colour and it looks very good on older woods. Thompsons water seal will peel and look like crap within a year. Dulux product will never peel as it is just an oil product. Also, I would angle grind off any serious rust before priming, even with a rust primer. Can never be too safe.

@charliefarms1

3 ай бұрын

I’ll check it out. I’ve actually had really good results with Thompsons. I have an equipment hauler that I did it to almost 3 years ago that’s holding up decent. Will probably need another coat next year. It’s in my cattle hauler trailer too.

@mitchellmaceachern4760

3 ай бұрын

@@charliefarms1you’re lucky. I’m a painting contractor and decks that use it all look like crap within a year. Could very well be the winter weathers around here, I don’t know how much snow you guys get.

Awesome job! It can be tremendously satisfying. Have you tried tractor/implement paint? It's what I've used on trailers, holds up very well.

8:00 your ranger sounds like a beast, mine didnt sound like that lol

Get the cheap Chicago electric welder from harbor freight for under $100. It’ll make welding thin steel much easier. Since it’s a mig and not stick. You’ll have an easier time starting the arc with less risk of burn through.

@charliefarms1

3 ай бұрын

I definitely need another welder. I plan on getting one before spring for sure. I know that in the past I could weld much better with mig

This guy gets a good work ethic

Nice little profit but how many beat up cheap trailers arr you going to find for sale?

Welding steel is the easiest, practice on more scrap metal so you don't have to pay a welding shop. Then the money you save by doing it yourself could've went to replacing all the boards, that's my only complaint. Nice job overall

gracias por compartir

great vid, would be awesome if you could post links to the hardware you purchased for us.

@charliefarms1

3 ай бұрын

Will do on the next one

Heck yeah 🇺🇸

Great video! I would love to find a $1600 dual axle trailer! What about the wheel bearings and trailer brakes?

@charliefarms1

5 ай бұрын

Thanks! This one had brakes on the front axle, but honestly I had never wired brakes or used them so I didn’t wire them up to work. Most people around here don’t use brakes on trailers anyway, so I knew it wouldn’t make much of a difference in value. For wheel bearings I get the wheels in the air and see if there’s any movement and that can typically tell you if they need to be done. I always pull the dust cap off to see what the grease is looking like too. I spend the extra time to check the bearings before buying the trailer too because that can usually get a discount.

@NorthernChris1

5 ай бұрын

@@charliefarms1 awesome! thanks for the detailed reply! I subscribed, loved the video! In Canada where I am from trailer brakes are always a good selling feature, that trailer would cost at least $4000+ CDN here

@ashleighelizabeth5916

2 ай бұрын

@@charliefarms1 makes me shudder to hear "people around here don't use brakes on their trailer". For an empty trailer that's all well and good but with a vehicle on it??? Well let me put it this way, even with working trailer brakes and an adjustable brake controller installed in my truck I make sure to give a lot of runoff room in front of me when pulling a heavy trailer. That don't even account for fear of getting jack knifed by a trailer with no brakes in stopping conditions that are less than ideal.

Taxes: Not reported 😂

I would’ve paid more for that!

Nice work. Do you usually get titles with the trailers? Do you have to have title to sell it?

@charliefarms1

6 ай бұрын

I’m in Kentucky, so trailers don’t have to be registered or plated unless they are used for businesses. So typically I don’t have to worry about titles

A lot of people can/would do most of that in a flip. I think the small thing that really made this a quality flip is that you went through and did the lighting! Looks really good, got a sub from me!

@charliefarms1

3 ай бұрын

Thanks!

Did you repack the wheel bearings?

Damn that welding shop is extremely affordable where you are at for all that work the welders here would have charged me 200$

I think the one side bracket is for the license plate witch is why its only on the one side

I’m confused as to how you even see the indicator. Would it not make more sense to get a light on the back with indicator, tail/brake and reverse all in one? Other than that it’s pretty good. The mismatched boards would drive me nuts. Is a wooden floor trailer normal in America?

Did you use deck boards?

I promise that paint will be flaking right off

@charliefarms1

5 ай бұрын

Oooooh do you promise?

Respect

What kind of welder do you use?

Remove one side of the angle where the dovetail starts and lay the new wood in. Your hustle is good, but work smarter not harder.

you know your sh##&*&*- thats a great job- my hats off to ya -mike

Interested in the overpants you're wearing, what are they?

@charliefarms1

3 ай бұрын

They are Carhartt insulated bibs. They are awesome

Like putting lipstick on a pig good work

Not sure where you live, but where I am you could easily get another $1K on the sale price.

@ashleighelizabeth5916

2 ай бұрын

Seemed like a high buy in price at the beginning and a low sell out price at the end to me.

The reflective tape is there for a reason, if you remove it, put it back on.

@charliefarms1

5 ай бұрын

Not required by law in my state

@TuffMcAwesome

5 ай бұрын

@@charliefarms1 oh, well if its not required Ill just fuckin plow into ya at night.

How much should I be looking for to buy a trailer for to flip it? I’ve been scouting marketplace for a few weeks now and just wondering how much a good price is to flip a tamden trailer for?

@charliefarms1

Ай бұрын

It all kinda depends on the trailer and your location. For example, I’m in Kentucky, so car haulers and utility trailers are very common. I’d say 1 out of 4 people have a trailer in my area. But when I lived in Florida, not many people used those types of trailers, but tons of people have boats. So If I was in Florida I would probably be flipping boats/boat trailers instead. If you watch my video on how to find trailer cheap, I go over the things I look for when buying one. Typically I pay between 1000-2000 for the trailers I flip because I know they cost 3800-4500 brand new, and I can make them look brand new and sell for half the cost. I always always always calculate how much I would have in the repair before buying the trailer to make sure it’s worth it. I suggest saving trailers on marketplace, then going back and seeing what sells. That will give you an idea of their value and how fast they sell

@coltonjackson3134

Ай бұрын

@@charliefarms1Awesome, Thanks!

Have you tried spraying bleach on the old original wood? Sometimes that gets rid of the black and makes the stain/ seal look more uniform.

@charliefarms1

4 ай бұрын

Good idea. I’ll try it next time

Great video, man. Proof that a man can earn an honest wage with an honest day’s work. What do you do for the undercarriage? I would imagine it’s corroded some.

@charliefarms1

5 ай бұрын

The undercarriage gets the same treatment as the rest of the trailer, I just didn’t film it since I had to raise it up in my barn and the lighting is too dark to video.