Easy DIY Table Saw Infeed Extension
Тәжірибелік нұсқаулар және стиль
This is an easy DIY in-feed extention to add to your table saw. This will make your woodworking projects easier and safer when working with longer baords. I made mine for a Dewalt jobsite saw but this build would work an just about any table saw. In my opinion, this table saw fence upgrade increases accuracy and saftey as well.
Tools and materials used in this video:
Self centering jig - a.co/d/1sbIsTV
UHMW polypropylene board - www.woodcraft.com/products/uh...
Other tools I regularly use:
Bosch CC2430 Clic-Change 1/4 in. Self-Centering Drill Bit Assortment (3-Piece) a.co/d/bW84GLk
Corner Clamps - www.rockler.com/rockler-clamp...
Pocket hole Jig.
www.kregtool.com/shop/pocket-...
O'SKOOL Self Centering Dowel Jig Kit Drilling Guide Bushings Set 6 inch Wood Wide Capacity Doweling Jig Puncher Locator Joints Tool a.co/d/dDyrfPt
Пікірлер: 30
I've been watching 'infeed support' videos all morning and I've got to say that I think that your video is the best. I love your design and your 'teaching instructions' have made it simple to construct. Thanks for the video.
@Ray_Here
6 ай бұрын
Thank you! You made my day!
Great job. If I hadn't had so many small hoarded MDF scraps, I'd have used sheet plastic too!
@Ray_Here
8 ай бұрын
Thanks! I’m glad you liked the video.
Great video. Thanks for doing the research for the rest of us!
@Ray_Here
Жыл бұрын
Thanks for the comment!!
Great idea Ray! I just added (last week) the UHMW polypropylene board (24 in) to my fence. Great upgrade. I am going to upgrade my router table fence in the future and will use the existing fence material and upgrade to your design. Thanks.
@Ray_Here
Жыл бұрын
Thank you Brian! I appreciate you taking time to comment.
Ray, thanks for the great idea! I have the same saw and also need to add an outfeed table like yours.
@Ray_Here
10 ай бұрын
Thanks! Here is my video about how I updated and added a new out-feed and side wing platform to my table saw cart. It may be helpful to you. kzread.info/dash/bejne/p3ZqyZJ7nbCwcpM.html
I enjoyed your presentation - very well done. I believe you would have made a great teacher as well. I made one of the UHMW boards to my existing table saw fence (Laguna fusion) a year or so ago but I forgot to change the measuring tape to accommodate the added width to my fence. Thanks for bringing that up in your video.
@Ray_Here
Жыл бұрын
Thanks you for your very kind words. I appreciate them!
great idea, thanks for the tip 👍
@Ray_Here
11 ай бұрын
Thanks. Glad it was helpful.
Interesting ideas !
@Ray_Here
4 ай бұрын
Thank you!!
Great idea! I think I'll do the same for mine :)
@Ray_Here
Ай бұрын
Thanks for letting me know! I hope it works out for you.
Thanks for putting this video out on YT. This is a great idea and I think very helpful for longer narrow boards. Another challenge with the Dewalt saw is when using a cross cut sled. The in feed area is still too short. Have you any solutions for that? I have a similar cart to yours and am trying to figure out a way to install an in feed support behind the runner grove on the left of the blade to thus better support my cross cut sled. Thanks!
@Ray_Here
3 ай бұрын
Try this. kzread.info/dash/bejne/aqVk2JRsnKq_YNY.html
Good video. I've been trying to figure out something exactly like you show. Do you think this can be done with some 3/4" birch plywood?
@Ray_Here
9 ай бұрын
Thanks. That would probably work. Just make sure it’s flat. Good luck!
@NateDizity1420
9 ай бұрын
@@Ray_Here thanks for reply. Yea the square & flatness of plywood may be a issue. I was just trying not to spend $60 if I could do it with what I already have. Thanks again
Nice project, good video! Which dowel jig do you have? Do you like it?
@Ray_Here
7 ай бұрын
Thanks. The centering jig is by O’Skool. Here’s the link. a.co/d/dDyrfPt
Hi Izzy I would like to order one if it’s available I have Dwe 7491RS
@Ray_Here
9 ай бұрын
Hi! I think you meant to leave your comment on Izzy Swans channel.
I’m attaching two videos. One is a general upgrade to my stand. The other is an infeed support for the crosscut sled. Hopefully one will help you. kzread.info/dash/bejne/p3ZqyZJ7nbCwcpM.html kzread.info/dash/bejne/aqVk2JRsnKq_YNY.html
"Deflection" is the very reason to not make this with "Nylon"
@Ray_Here
3 ай бұрын
I can’t argue your point. I’ve really not had it be an issue though. You just have to be mindful that if you push too hard against it, deflection is a possibility. Thanks for your opinion!