I just reached 1000 subscribers which is really humbling, thanks everyone 😀 The adds are a little confusing however and I am worried that too many may be showing up, if you are seeing more than 3 sets of adds (beginning, middle, end) please let me know so I can try and fix it 🙏

Great to see someone doing good work in a typical home garage/shed workshop and not a mini factory. Well done.

Nice addition. I appreciate you not polishing out the issues.

@SloverOfTeuth

Жыл бұрын

Yep, it helps us avoid them. Nice clean project, well thought through.

I worked at an Overhead Door dealer and we called your garage door a 'shin kicker'.That is a nice extension outfeed table. Thank you for sharing.

You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice kzread.infoUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.

@macsworkshop

11 ай бұрын

Gracias ☺️

I can't believe this channel only just drifted across my timeline. So epic

Nice production! Thanks for sharing the one off mistakes. Helps me to carry on in spite of all my mistakes! 🙂

Somewhere in my life I picked up some aluminum piano hinge, no wimpy stuff either. Probably 2.5 inches wide total and it is 3/16 thick. I bolted a piece of wood to the rear of my saw and the side extension for my 52" Bimeyer fence, screwed the piano hinge to that then built an outfeed table similar to yours but used 1" square alum tube for the frame and particle board (coated with 3 coats of satin poly). I added two 1" steel square tube legs that fold to each corner, these have adjustable rubber feet so wherever I set my saw up in the garage I can account for the floor being uneven. I also made a side extension that allows me to cut wide material by bolting a piece of angle iron on the side of the table. One end of the extension sits on the angle and there are 3 tapped 1/4-20 holes in the angle to attach the extension to and a simple square support leg made out of 1 x 4 supports the outer end. It has a flat wood top with a 1/4-20 machine screw insert , I use a few wide wood shims under that leg to level it.

Clever use of a rolling pin. That's a much cheaper alternative to buying those special rollers. Thanks for sharing this.

Two tips. Add another coat of contact cement. First layer smoothes out tiny peaks and valleys. Or you can add varnish/shellac than one coat of contact cement. And second tip is to use one inch wide rollers. This prevents the pressure from spreading out over the width of the baking roller. For an outfeed table I'm sure a few bubbles will be OK. But using 1 inch rollers will eliminate any issues. And great build! Enjoyed the video

Thumbs up does not describe my appreciation of your video and thoughts; I want to make one. Thank you!!

nice design and execution. Thanks for showing some of the obstacles along the way and how you solved them.

I've seen lots of outfeed tables, but this is closest to my saw design and functionality that I'm looking for. Great job! I will be doing this for my sawtable for sure!

I like this I have a small shop too. A regular out feed table would be in the way most of the time. You can score Formica like glass and snap it. They sell a specific blade for that, Also a hand trimming "plane". They also have a beveling router bit for that. I guess I have been around when Formica was used more often.

I cannot belive you only got 5k subscribers. This was very enjoyable and surprisingly relaxing to watch. Keep it up! 🎉

Great solution. I love watching videos made by woodworkers in other English speaking countries and hearing different terms for tools than used in the US. “Thicknesses” and “Linisher”.

I also have a small space. My first go at outfeed table was made purely of plywood. This takes up too much space making it awkward to access the machines at the back end of the garage. A folding outfeed table would give me the additional space to use the machines on the back wall. I feel like setting up your shop comes in several evolutions. Your basic setup to get you going. A second round where you make improvements on your initial design. And sometimes a final go to hone in your efforts. Thanks for this vid. Very well done.

Thanks for sharing, i built a nearly identical one for my Unisaw last year. I used industrial door hinges for the hinge off of the table saw and two 45 degree supports placed manually. I like your mid hinge folding design.

First, thanks for sharing the "UPS and Downs" we all encounter during our engineering mistakes & infrequent success..you've inspired me to get this done, as I have put off building an outfeed extension for too long..consider me subscribed and again, thanks for the nudge forward!

I have a new Harvey table saw looks exactly like yours, was trying to figure out how to do this and found your video. Thank you very much for making this and putting it on the KZreads!

@macsworkshop

Жыл бұрын

That's great to hear! I didnt even realize mine was like that until I came out in the morning to start the project, then I had to go back to the drawing board to work out how to do it :)

Excellent video.......I've been thinking about building a tablesaw extension table for quite a while and your clever design fits the bill perfectly. Thanks so much for documenting your journey for all us sawdust creators.

Turned out great! It looks as good as it is functional! Thanks for sharing your time and talent!

Great video, thanks. Was so good to see that I'm not the only one to make mistakes. Now I just need to learn to just carry on.

Excellent work!

That was great. I have a contractor saw on a roll around stand and this gives me ideas! Thanks!

Your videos have an ASMR quality to them. They are very relaxing to watch! keep up the great work

Thanks Mac. Great video. I am finishing organizing my shop today and will build that outfeed table in a about 2 weeks! Take care!

New subscriber and I agree! Why you are at only 5000 subs is mind boggling!! Outstanding build, great solution to a very common issue for us small shop folks, and honest reveal of oversights any of us would replicate! But you were equally as generous with the solutions! And, you didn’t jury rig it…you went BACK and did so it worked!! That’s called work ethic and is becoming a very rare character trait!👍🏻 I’ll be following your lead!!

Great video~! I've been looking for an out-feed extension for my table saw and this is the best one I've seen so far. Excellent job~!

This is the best vid I’ve seen of the exact outfeed table I want to build. Thank you!!!

Well done also. I made up a similar one about six years ago with a few changes. I added a rail to the top on the table saw for the top to hook into and a rail for the bottom of the table saw to provide more support for the angled support. I added two cleats cleat to the underside of the top. One to hook into the table saw and the other for the leg to fit against. Lastly, I simply use a board(30cm wide) with mitred ends to sit against the top and the other to sit on top of the bottom table saw rail....the board adds great stability to the top. All parts simply hook into place when needed and lie flat anywhere when not needed.

THANK YOU...I Recently built an outfeed/assembly table...but my mistake was that my table top was higher than my saw table which wouldn't allow me to move product off the table saw to the outfeed table...my fix to that was to raise the table saw which is a whole other issue...Then I saw your outfeed table which is perfect...I now have a dedicated assembly table and will be building your version of an outfeed table...Again...THANK YOU!!!

Very nice. Thank you for sharing this with us. Everyone stay warm, safe, happy and healthy. From Henrico County Virginia

Very creative table saw extension, well done and thanks for sharing this video with us 🙏🏼

Very nice fold down out feed table. At home I have a cabinet where the top is the out feed table but where I go for part of winter has a shop with no outfeed surface. It scares me to see people cutting things that are too long. I’m going to use your idea a build one when I get there February 1st. Thanks and it is a very good video. Good content, the right amount of talking and a great attitude.

Very nice . i see you have the high tech open garage door dust control system that i also have😂

@macsworkshop

4 ай бұрын

Hahaha, yup, works a treat 😂

Very clever leg system. Well done.

Thank you. I will be doing this to my table saw and have been looking for a good plan. My search is over

Well done! I’ve been searching for extension table ideas. I have a Powermatic cabinet TS with a similar rail. This will be perfect.

Beautiful job. Good video and audio on top of the nice pace and good explanation, thanks!

I agree fully with the why a feed table is needed. Very well done. That drill press boring, needs some safety adjustment. Really enjoyed,thanks

I loved this project ! Awesome

👏🏼great job. Love the design and build. Good inspiration on build idea for my set up.

Very nice design and execution and thanks for sharing the mistakes & oversights. I make my share, and its always nice to learn from others rather than from myself.

Looks very good

Nice job mate, thanks for sharing 👌

The Guy Ritchie_Esque montage of redoing the legs was perfect!!!!

Great video Kris,

Very good, Sir. I was impressed. I just finished building an out feed table like the one that Colin Kanat at WoodworkWeb built. If I had seen your video I may have built one like you have demonstrated so well. The concept on both is pretty much the same whereas you built the folding support and I purchased my brackets as Colin did. With the price of boards it might have been a wash dollar wise. I have to say that yours is much better looking as you took great pains to make it so. I am going to check out your video on "How to build a cross cut sled at any budget!" because I have built 2 or 3 through the years that I did not care for. Again, very well done, Sir. A 73 year old admirer from Bossier City, Louisiana. I only say that because I do not think you accent is from the bayou.

Nice job. Looks great. 👏👏👏

You did a great job 👍👍👍

Thank you for your wonderful video. Im brand new to woodworking. You're so talented.

I'd better break these bad habits too. I'm watching your video and I will make one of these. Thank you.

Excellent work. I'm about to build one for my new sawstop - thanks for sharing :)

Nice work!

have to agree with you, our big saws perhaps 70+"s wide have only about a foot of table behind the blade, and yes I do as you did, some how made it to 60 with only taking a small piece off the side of the tip of a thumb.

Lots of news knowledge from your video. Tqvm

Nice warts and all video! Good job! 👍

Love this outfeed table. It will work perfectly with my Jet tablesaw.

Awesome job!!.. Thanks for sharing

You an absolute genius 👍👍

Enjoyed this!

Glad to see other people make mistakes. Good plan, I'll make one.

I have a 1954 DeWalt 8 inch radial saw that needs a new table. The problem is getting the green monster through a door. Folding side tables looks to be just the ticket. TKY VM

Idea: If you don’t round over the pivot part of the leg on both sides, then maybe it can act as a stop block on its own.

nicely done

For a large glue up like the table top I use a pin nailer to keep the 2 pieces straight nd then add enough concrete blocks to cover the top. No clamps needed nor do I have any screws in the top to get in the way eventually. None at all...Forstner bits do not need pilot holes.. Don't want "blow out", use a wooden table that you can drill into Either that or set the depth gauge so that the point of the bit will emerge and then turn the piece over and finish the hole. Your basic design and I will be using the ideas on my out feed table soon... I envy your drill press as my old Craftsman press does not have a crank on the table for adjustment. It is older than I am and I am 75 now...

Thank you. I have a Harvey saw that has the issues you addressed other than my dust port is on the rear of the saw. Not a big issue.

The local Home Depot (not sure what's where you are) has something called "Glasliner 4 ft. x 8 ft. White .090 FRP Wall Board" which is awesome stuff, it's amazing how many uses you may be able to find -- I've actually made sandwich board signs using it with stencils and plastic-enamel paint. It is stippled on one side, but the other side is quite smooth, and perfect for many _many_ purposes. It may be quite good to replace the Formica as a top for something like this. As I speak it's US$43. There is also a 1/16 panel of similar stuff for US$26. BTW, the term for making/adhering the formica to the underlayment is called *"burnishing".* There are specific tools made for the job, but a kitchen roller can certainly do the job. Not sure I'd want to use it for food after that, but it's something worth having anyway. Oh, and I see you're using Titebond III -- it's good for peeps to understand the difference between the two main forms -- TBII and TBIII -- they use different processes for curing, so you want to know which will work best for your environment. TBII is best for relatively dry environments. Whereas TBIII is best for relatively humid environments. E.g., if you live in Arizona, use TBII. If you live in Florida, Louisiana, or the Gulf zone of Texas, you want TBIII -- this is because TBII cures by *releasing* moisture, so high humidity can be an issue. TBIII, on the other hand, cures by *absorbing* moisture. So it's great in high-humidity areas. It's also notably more waterproof, but the downside of TBIII is that it also tends to foam as it dries, leading to some extra cleanup as the foam is exposed in some places. Your choice, but I'd feel a lot more comfortable with two legs just dropping down at each corner and sitting on the ground, with a lock-in-place... I don't see any benefit to the clunky angle- trick you did there. It feels needlessly "cute"... And it leaves the corners unsupported, so the whole thing is subject to torsion damage over time. YMMV. ;-)

@macsworkshop

6 ай бұрын

Thanks for the info, especially about the titebond glue 👍

Very nice job.

Great job! Just subscribed can’t wait to watch this channel grow

@macsworkshop

Жыл бұрын

Thanks Ben 😊 I’ll hopefully have a new video out this week!

Great video that compelled me to subscribe.

Meets all our needs!

My new tablesaw arrives this week. This is going to be my first project on it. Cheers from across the ditch cuz🤘

@macsworkshop

Жыл бұрын

Awesome, I’d love to see a pic of it when your done, maybe on instagram?

You needed a out feed table to build your out feed table😂 great job!!

Nice outfeed table

Very nice design and great execution! I like how you minimized the horizontal projection of the wood rail/hinge you bolted to rear fence rail. I’ve seen other designs that add what looks like 4-5” to the saw’s depth (which is not good if the saw shares space with a car). Externally, your saw looks very similar to the Grizzly G0899 and Shop Fox W1888. The fence rail setup is the same, as are the hand cranks, the fence, etc. Owners of those saws could use your design as-is.

Very nice

Very nice!!

I’m building this out feed table, my table saw has the same piece of angle iron on the outfeed side of the table saw.

Kia ora bro, your a right lil vegeiemite, that is so simple but so practical, I will copy that onto my to be done urgently list

Nice job, my only critique is PLEASE shim your miter saw to be flush with your countertop 😂 every time you were making a cut and pushing down the edge flat to the saw, you could see the tail lift off the counter. Means that you can't make square cuts with it lol

I cut part of my left thumb off trying to catch a piece before it fell off the back of my saw. It was a long time before I used the saw again.😣

Use a sheet of plastic when gluing up Formica. Put the sheet between the gluing surfaces and remove it as you roll down the Formica.

@jeffsapp9951

8 ай бұрын

There is always a “that guy”….. You are “that guy”….

Well done video. 👍 I need to do something similar but I’m to busy watching other people build things then actually being productive. 😅 Subbed

@macsworkshop

Жыл бұрын

I’ve been totally guilty of that in the past 😆

This is amazing and clean! Best design on youtube! Keep it going!!

I was very concerned every time he used the drill press. Holding the piece while using the drill press is a definitely a safety hazard. If the bit were to catch, it could spin the piece around pulling your hand into the bit. I have seen a coworker take a chunk out of their hand that way. please use the clamps when able and work safe. otherwise, Great video. Thanks.

nice

Having chopped 3 fingers off on my saw, I can attest to how right you are.

Mac, very nice job. Personally i would have made a catch or bracket where this leg attaches to. Now there's only a metal edge, which it is leaning on. I'm afraid that when there's some vibration or someone bumps into it, your outfeedtable will fall down.

@macsworkshop

2 жыл бұрын

Hey Barrie That's a fair call and I might do a short or something in the future if I have issues. Because the table is double 18mm MDF, its pretty darn heavy and i haven't managed to bump it out yet, I'm actually more concerned that the bend in the leg will flop out and im thinking about putting a catch on it to ensure that doesn't happen

@Method_MOK

Жыл бұрын

you can add a couple rare earth magnets where the leg meets the cabinet ... those are quite strongthese days and would prevent minor bumps from allowing the leg to slip off the ledge

@pwknight7

Жыл бұрын

A slight variation is to not even make the leg, simply use a board instead, cut top mitre angle to fit neatly under the outer edge of the extension and sit the other end down on the table saw lower lip. I have had mine like this for years and never once bumped it. My top simply hooks over the extra timber lip on the table top and I locate it by sliding two bolts between the two faces. Both table and support board store flat and take seconds to install. The extra bonus is that they are always aligned with the saw table top and are independent of having to adjust the leg as it is never in contact with the ground and its bumpy bits. P.S. Cut some holes in the board to reduce its wight without affecting its stiffness 16-18mm thickness is good.

This is a great plan. I don’t think you needed the pretty Formica. It’s a “work” bench so I’m guessing cheap plywood would work just as well. I’m going use your idea to adapt to my table saw (which doesn’t have the metal thing). Thx.

@macsworkshop

Жыл бұрын

The Formica helps the wood slip nicely, kind of like how we wax the saw bed so the wood doesn’t stick as it goes thru

Brilliant only a couple of mistakes considering it's a one off build on the fly an excellent result 😊

I made a similar support for my mobile miter saw table. I laminated two MDF panels with a water based glue. After laminating the Formica on one side, the panels warped. A more experienced maker told me I should have waited a week before laminating the Formica or laminated top and bottom to prevent differential drying. Wondering if you had any tips on timing or warping in your project? Great addition to the shop! I greatly enjoy your videos.

@macsworkshop

Жыл бұрын

Hey there I thankfully didn't have any issues with warping but I did notice on a separate project where I glued two pieces of MDF together that they didn't stick particularly well. I think the one reason this worked without warping or the glue coming undone is because I ended up screwing it together from the underside

was remaking the leg sections anything like taking the next exit and then turning around to get back to the exit you should have taken? I think that's what it would have been like for me, great build, got really lucky twice with those screw locations, was bound to go wrong somewhere else

Really should have 2 legs, and a better brace support on the bottom of the saw for the legs to rest in a pocket. Sometimes your going to cut something big and heavy youll want the extra support. Lets say your making cabnits a 3/4" plywood or mdf gets pretty heavy by yourself youll be asking the off table to support that weight. Last thing you need is the lone leg to give in. That could be worse then not having the off table in the first place. Always better to overbuild it.

Great video. I just got a Harvey table saw that I'm going to build a outfeed table like yours. What is the width of pine boards you used for the mounting block.

Great video Mac. I’m going to adopt a few of your ideas. Please tell me, what’s that nifty countersink bit you’re using called and where can I buy one?

@macsworkshop

Жыл бұрын

I got it from my local hardware store (bunnings) however I wouldnt recommend it, the rubber ring often leaves black marks on the wood. A similar product I have seen many other woodworkers use that is on my wishlist can be found at amazon - amzn.to/3ht0Fvh

Superb solution, work and video. Loved it! One thing puzzles me. At 12:40 we see you remove the protective film but it still seems to be there at 22:22. Regards, Phil

@macsworkshop

Жыл бұрын

Thanks 😊 I just double checked and the film is gone at 22:22, what I think you are seeing is where I drew with pencil on it and removed the pencil with an eraser, it left those strange marks there, which have since disappeared with use.

Great job. What's the model of that little Makita router you use? Do you like it?

NICE JOB !!! I AM AMAZED AT HOW FIGURED THAT DESIGN OUT... I CAN NOT USE ALL OF IT ON MY SAW ,, BEING MY MOTOR STICKS OUT BEHIND THE SAW. BUT NOW I KNOW HOW TO ATTACH IT AT LEAST... THANK YOU....