Did I miss something ? How did you get it off ?

Two of the many things I have learned in my almost half century of repairing cars are 1)If you don't have what you need tool wise and can borrow it, do so. but if you think or know you will need it again, buy it. 2)If you buy the best you will only have to buy it once.

@seanpaul3050

2 жыл бұрын

Or do what I do. Buy that tool anyway. And then sell it as ‘used only once’ on eBay afterwards. I usually get most of my money back. Obviously I only do this with tools that would very rarely get used.

I'm confused, how is this a video on how to replace? You didn't even show it coming fully off let alone how to install the new one.

I just did my one (on an X3) BMW. After loading it up on the puller using a 10 tonne hydraulic bearing puller) it still required a tap using an old wood chisel between the shaft and the inner race...bang...

Great quality video thanks!!

Hi Nathan,I'm after your help,I've recently bought an x3 which had a slight rumble noise on acceleration,on further inspection it appears that there isn't a front propshaft,but obviously it should be there,I'm going to buy one and put it on,but would this explain the rumbling noise in the lower gears and clunking...many thanks nigel

Another great video, thanks 😁

Same harbor freight pullers I have ! Lol I took an wd-40 the threads an light anti-seize prior to use an ran it up an down serval times an they have held up ok. I used them on same exact thing lol . Guess I got lucky .

I Love how easy this kzread.infoUgkxvAj3godqGAIP5rApM1laH767JGtPG1-h carrier is to adjust from my friend to me taking turns holding the baby! It provides great support on my back too! This has definitely made shopping easier! I always get asked where I get it too!

You might be a tooth off because you didn't market before you took it off. check the u-joints laying flat on a table and you will know

Does anyone know if the drive shaft carrier center support bearing same for a manual transmission as an automatic.. car in question is a 98 bmw 528??

Selam. BMW X5 e53 code 2003 model 4.4i kullanıyorum. Özellikle aracımın motoru sıcakken Aracımı D ye alırken one atılma,isteksizlik ve dururken 5 kilometre civarı öne atlama yapıyor . Lütfen cevap verirmisiniz?

A little silver anti seize on the puller threads will some times help.

@kamoterorl

7 ай бұрын

Definitely lube the treads, grease or antiseize. Depending on the situation Lube the end of the threaded rod also where it is going to spin on the work piece.

You better Grease the threads on that puller if you want to use it a couple more times get the cut saw three and a half inch angle grinder bada bing bada boom or if you want to have fun get in there chisel on an angle little on one side little on the other walk it right off I used to do this the big trucks or warm it up

I did mine . I'm sorry I didn't do the rubber thingy.show how to do the ujoint lol

I dislike taking off the driveshaft ony e30. Such a pain in the butt especially if you have to be laying on the floor. My e30 center support bearing shield needs to be replaced because it makes a grinding noise when im in the higher rpms.

It does the job

I just cut mine off with an angle grinder when I replaced the bearing on my e39. New one went on pretty easy. That vid wasn't up to your normal standards.

Why would you show an incomplete video? Why start if you're not going to finish it? That sucks!

Wow to much pressure to pull that part probably a lil bit of Pb blaster and i think work

And that showed us absolutely nothing !

I suppose you could hack it off with an angle grinder

This crap tool wasn't designed for use on BMW... It happened to me couple of times as well... However, If I you need tool for one time use, you can rent it from many the automotive Stores. Worked for me.

Nice job with that marking, lol

Did I just see a circlip flying off

A cut off wheel is much cheaper

never seen a shop with enough tools much less too many

yo

I can't believe a little old BMW has to have a carrier bearing. We drive an F250 four-wheel drive pickup 8 ft bed extended cab it don't need no carrier bearing. I hope my wife's 2009 328i don't have one it's just more pieces of s*** to fix. I change my BMW emblem, two POS piece of s***

@ruffraff4697

Жыл бұрын

Most Trucks use solid shaft,Why would you buy it then? Your wife's 328i is going to have all the bm's specialty's

FIRST!!

Fail

OMG what a terrible video, no shot of getting it off!