No video
Ducati Panigale V4 | Front Head Timing Cover Gasket Replacement
Welcome back to the channel. Today, we are replacing the front head timing cover gasket. I want to give a special thanks to Derrick - @ESBKLife. He pointed me in the right direction on the leak and gave me tips and advice on fixing the problem. Check out his channel. He makes amazing content.
Derrick, thanks again for your help!
@ESBKLife
video content:
0:00 - Intro
1:45 - OEM Parts needed
4:39 - Draining Radiator
6:28 - Front Wheel Removal
7:26 - Radiator & Shroud Removal
13:30 - Shroud Removed
16:45 - Ignition Coils Removed
23:08 - 4 Cover Screws Removed
24:28 - Timing Cover Removed
27:15 - Old Gasket Removed
28:40 - New Gasket Installed
31:40 - New Cover Screws Set up
34:40 - Timing Cover Reinstalled - Torque to 10Nm
42:34 - Project Complete
Пікірлер: 39
Thanx. I just did mine front and back valve cover gasket yesterday, took me like 7 hrs.
@MotoGarageTV
8 ай бұрын
Nice work!
Thank for teaching me ❤ I like this video ❤ for build v4 fan club from thailand 🇹🇭
@MotoGarageTV
10 ай бұрын
I'm glad you like it
Dude, you're a few subscribers away from eligibility for monetization!
great vid thanks for sharing ;)
@MotoGarageTV
8 ай бұрын
Thanks for watching!
감사합니다 많이 도움 되네요
@MotoGarageTV
Жыл бұрын
You're welcome
Are you a mechanic by trade? Great info! Thanks for the content
@MotoGarageTV
Жыл бұрын
I'm not a mechanic by trade. I've been working on my own bikes since I could remember. I try and research my projects before I start and use shop manuals to fill the gaps. Sometimes, I have to take things apart and explore before understanding the problems. I should probably put some type of disclaimer in my videos
Mine has just started to leak (21' V4s). Anyone who has had the gasket replaced had the issue re-occur? I am thinking when I replace mine that I put RTV bond on the head as well to make sure there is a really good seal
@MotoGarageTV
5 ай бұрын
Definitely use the RTV as well.
Great vid! What are the torque specs for the cover bolts?
@MotoGarageTV
Жыл бұрын
I couldn't find torque specs on these particular bolts. I went with what I thought was good based on how tight they felt backing them out.
Very informative video but i think theres a sealant that needs to be applied on the both covers where the rubber gasket sits on.
@MotoGarageTV
10 ай бұрын
You are right, I mentioned that in my video, and I applied off camera. Very important tip. Thank you
@TWOTEN_DAILY
10 ай бұрын
Awesome 👍 mine is leaking from front and rear cylinders but not too bad to where you loose alot of oil. I have all the parts for the front and rear im just waiting for it to get really worse then imma start on it 👍
@MotoGarageTV
10 ай бұрын
@novasevenfold502 I hear you, no sense of fixing it if it's not broken.
did you have to put the rtv in the channel all the way around before pushing the gasket on? did you have to clean old rtv out? confused about that part
@MotoGarageTV
10 ай бұрын
There were only a few spots where I saw old RTV from the factory inside the cover. Little cleaning is required, I also prepped the channel with some some rubbing alcohol. There was nothing on the head itself. I applied a small bead of RTV around the whole channel before installing the new gasket.
Hi, there. I have the same leak on my 2018 Ducati Panigale V4S. I have to replace the valve cover gasket, do you know whats the torque spec on the 4 bolts for the valve cover?
@MotoGarageTV
8 ай бұрын
Hey, I don't recall what that torque amount was. Just guessing I would say around 10-15nm
What’s the part number of the gasket and the 2 seals?
@MotoGarageTV
11 ай бұрын
Stop the video at 2:15, and you will see the parts listed. I highlighted them in yellow.
@JVSKRR-is7qr
11 ай бұрын
Thanks for responding. Im about to do mine tomorrow. Looks like it’s tricky to put the cover on especially with the rtv gasket maker on it too. Any tips to make it easier to install?
@MotoGarageTV
11 ай бұрын
@JVSKRR-is7qr hey hope this reaches you in time before your installation. I'll let you know what worked for me. I applied a small amount of the RTV inside the groove where the gasket would insert, then pressed in the gasket. I turned the cover over and just let the weight of itself hold the gasket in place. I let this sit for about 10-15 minutes before installing. This helped hold the gasket in place while installing. I suggest temporarily zip tying cables/ lines out of your way to allow an easier install of the cover. I was fighting some wires and ended using a few zip ties and made a huge difference. Hope this helps.
Why are you replacing a valve cover gasket on a new bike?? Was it leaking? How many miles on the bike?
@MotoGarageTV
Жыл бұрын
Yes, it was leaking. The bike has 5k in miles. I'm the second owner, I imagine since it's just a rubber gasket, the original owner let the bike sit and the seal dried out. It was a small leak and a relatively easy ands low cost item to fix.
@MaciusSzwed
Жыл бұрын
@@MotoGarageTV I see, good work and nice you are sharing it with other people
@MotoGarageTV
Жыл бұрын
@Max Biaggi thank you, I appreciate that. I tried looking up the process before I tackled this one and came up with zero hits. I'll continue to post my work. Thanks again
What is the torque please? Thanks
@MotoGarageTV
2 ай бұрын
Hey, I have a picture pulled from the service manual, but I can't attach it to this comment. Torque on those bolts is 10Nm.
@renesoyyo
2 ай бұрын
@@MotoGarageTV thank you👍 very good video.
Mate, how much did this build cost😂? I’ve rebuilt several engines and reused all the hardware, just paying a few quid for the leaking gaskets. I appreciate the work though, don’t get me wrong.
@MotoGarageTV
Жыл бұрын
This repair in particular....$53 dollars. I could have just bought a new gasket and reused the bolts, and it would have been closer to $20 dollars.
@nitramh24
Жыл бұрын
@@MotoGarageTV Yeah, that’s all right. Fair prices, glad to hear that the maintenance parts are reasonably priced👍 But the other stuff you’ve put on is insane😂
@MotoGarageTV
Жыл бұрын
@NitroTruth tell me about it. I've spent about the same amount on add-on parts as I did on the purchase of this bike. Close to 18k in add-ons alone
@nitramh24
Жыл бұрын
@@MotoGarageTV Love it😂 I'd do the same if I had the money!!