Brilliant video & explanation. Thank you!

Even without desconneting the coolant pipe, you can still gently remove the mechatronic.

really nice video, thank you from Spain💪🏼

@MBAAUTO

5 ай бұрын

Our pleasure!

Great video, thank you

Thank you for the video

Thank you for good information!!!Very good video😀

@MBAAUTO

5 ай бұрын

Glad it was helpful!

Very good video buddy

Well explained

I have been looking for a recent video regarding mechatronics unit my polo 6 r line won't crank at all when starting i removed the starter and tested is the starter works perfectly tried to jump start it still didn't crank but the's this little sound that comes from the mechatronics unit when i turn the key to start it, the's no errors in the car nothing on the dash it just wouldn't start pleeeeease help me if you can Sir what might it be

@MBAAUTO

5 күн бұрын

If your from India contact me at +917972872576 Or send me your TCM number

@mzwandilethandanani1015

5 күн бұрын

And if I'm not from India i guess you won't help me 😢

Do you put transmission lever into park or neutral before removal

@MBAAUTO

4 күн бұрын

You can do it both ways P will be better

Super!!!!

@MBAAUTO

5 ай бұрын

Super!

Can you give as dimensions tool's for lock clutch ?

@MBAAUTO

Ай бұрын

Email me.or WhatsApp on +917972872576

@dRoZaable

24 күн бұрын

Find in store and buy it.

Hi there. I have a problem with my mk6 7speed vw golf.. some of the gear are not working... Gear. 1-3-5-7 are working. But. 2-4-6-& Reverse. Are not working. What can be the problem.. Kindly reply.....

@MBAAUTO

5 ай бұрын

Please check all fault codes and email me your scan reports at Aliautomech@gmail.com Looks like one of your sensors which detect clutch movement has stopped working

On the top ,the sound of the click ,do I need to return it back

@MBAAUTO

Ай бұрын

Nope

Can i put Neutral from inside the car before taking this out?

@MBAAUTO

5 ай бұрын

Sure no problem

My VW Polo fuse to the Mechatronic Control Module (TCM) is blown and keeps blowing due to a short to ground, this is creating fault code U0101 - Lost communication with TCM. I guess I need to remove the Mechatronic cable connector to determine whether the short to ground is in the TCM unit or is in the wiring up to the TCM unit. Any further advice? Thanks for sharing the video!

@MBAAUTO

3 ай бұрын

It's either 2 things 1st just set the volt meter to continuity and insert one of the probs into the couplers positive with ignition off and other prob to the battery negative (not on the body) If it beeps that the problem is on the car not the mechatronic 2nd if the above doesn't work than most probably you have a bad tcm plate

@MBAAUTO

3 ай бұрын

If your from india and around Goa than contact me on whatsapp @ +917972872576 Or email me aliautomech@gmail.com

@cyberlightbeing

3 ай бұрын

@@MBAAUTO Thank you but I am in the UK

@cyberlightbeing

3 ай бұрын

@@MBAAUTOYes I was going to do what you’ve suggested. If it turns out that the TMC is shorting. Then will the replacement require programming? If so then are the software/tools available easily? Thanks!

@MBAAUTO

3 ай бұрын

@@cyberlightbeing it depends where your from, just match the last alphabet and your good to go new ones cost alot just get a used one if it's a D than swapping will do