That X was the best thing i learned today. Thank you!!!!

You have explained this the best of anyone ! Thanks so much for sharing, this is very valuable knowledge ! Maybe I can get the gaps more correct on my 68 Camaro now.😊

Thanks for that taped on "X" on the door, I haven't seen anyone do that, it's a great visual to keep novices like me remembering what the affects of any move is.

Years of experience you can tell by his cool and calm explanation.

I know I'm late saying thanks but you really helped

Thanks for the great instructions! Really good video!

This was very helpful. If you are replacing a quarter panel would align the door to the rocker panel/front cowl and then align the quarter panel to the door?

Excellent information. Thanks for making it. Been wrestling a 88 grand wagoneer door....I think I have made every mistake possible. Have one more. The front door seems more like a truck door hinge. Just need to get the bottom to pull in. I will put me an big "x" on it this weekend and have a beer to help my thinking then try it again...instead of using the drunk monkey technique used on the last three that I just got lucky on and learned nothing ....I learned more in this one video than doing it the 6 times I've attempted it on this jeep...thanks again

Awesome tutorial...

thanks so much

Thanks great way to explain it so even i could get it.

That was really interesting! I always wondered how you get all 4 sides to match so well.

❤ thank you very much Will this apply to 2nd gen f body as well. You make this seem easy. I've been aggravated at passenger side door. I just got my driver side door and window adjusted. I'm putting tape on my door to help me remember the adjustment. Thanks

Thanks. Will help re align my cadillac passenger door ✌️

so impressed .i over exstended my pu door 2014 gms 1500 . i put new hinges and the top of window frame whistles some air .wasnt sure about rolling window down and useing the block of wood to push it in about a 1/8 of a inch .i will try it .i can pull it in while driving and make the seal so its close . thanks for your instruction teacher ..!!

Great explanation. Bought an E-Bay hinge for my F150 and it did not fit worth a damn. Also forgot to capture the plate inside the cowl. Had a hell of a time. Ending putting the old hinge back on and got real lucky. Fits great. NOT AN EASY JOB!

Great video, thank you

Thank you for your valuable explanation

Can you make a video installing a door start to finish?

Great explanation. Moving the top hinge forward will raise the door like you explained. So moving the bottom hinge back should raise the door?? I have an 85 c10 an i just cant get consistent gaps. Top gap along the drip rail is wide it gets worse as you follow door towards the rear of the cab. Top rear gap along the cab is wider than the bottom rear gap. Give me a hard time.

Thanks, how do you adjust door latch catch posts, great videos, hope to see more

Thank you! Great content

Grate explanation ,thankyou very much

Nice tip I will be defenatley using it I'm redoing my 1964 impala 2 door coop ,one question do you have the internal winding mechanism and window in the door when you a line the door or not ,Jack

Thank you probably the best explanation I have found! Do you recommend the door latch hardware/Stryker on to do the adjustments?

@Americansupercar

5 ай бұрын

I usually leave it on but removing it could be helpful

My kid got hit by someone backing out on the passenger door, he beat the hasp and striker bar so bad and were talking a 40 year old. I had to replace the whole dam door. So i hung a salvage door on his car i closed it so it was latched then made sure the back was straight never looked at the bottom , when i was done it looked good all the lines matched up. One problem when you open it it drops slightly when you close it is raises up slightly but it works so i left it alone. And by the way the bottom is straight also, so im thinking the striker bar is off slightly. But im not going to adjust it. Good enough for government work. Its a 2005 car not a 50 year old collectors car at some point its headed back to a salvage yard anyway.

Thanks!👍🙏

Ty

not many understand to start from qtr , pivotal

Hinge pins?

So is tuning nut right moving in or out at bottom?

i backed up with the door open and bent the door too far. the front of the door overlaps the fender , plus the front of the door is hanging noticeably low. i can see the top hinge is bent outward bending it back hasn't fixed the gap. am i better off going to a junk yard and getting a hinger that's not bent than trying to fix these hinges?

@Americansupercar

6 ай бұрын

I will try to do a video on bending hindges this week so look for it

When closed all the way my door stands proud of the rear panel all the way down the rear gap. The front gap is nice and flush. So it looks like the door is not closed all the way.. How to fix that?

@Americansupercar

8 ай бұрын

Without knowing what kind of car were talking about ,this is a general answer ,it sounds like the door striker needs to be adjusted in

My 66 cadillac’s passenger door is as whole too low.

doreskin