👋 If you found this video helpful or enjoyable, please consider subscribing to my channel! 🙏 Your support would mean a lot to me and help me create more content for you. Thank you! 🤗

That is not true. The top space is ok to install a 360mm AIO, i did that without any issue.

@nburns11

11 ай бұрын

So did I , my AIO sits on top between the top panel and the radiator mount .

@gamesbykevin379

9 ай бұрын

Without a issue top space was enough and on the side also 360mm radiator fits great

@CrazyBRT

9 ай бұрын

did y'all installed motherboard and connect cables firt and AIO next or was AIO first? in this video it clearly shows there's no space for CPU cables to fit through after installing radiator + fans

@eebrohim7001

8 ай бұрын

​@@CrazyBRTthen just wire it before it's not difficult, no need to return it 😂😂😂

@FrogOf4Chan

8 ай бұрын

I also installed a 360mm radiator on top, I don't see what the issue is, plan ahead and build knowing what goes in what order, it wasn't bad at all- in fact this is the easiest case I've ever built in.

1. Why do you have the AIO set to exhaust out the side? You should have it as intake drawing fresh air into the case. 2. Install 3 (or 2) fans on the bottom of the case for intake for the gpu. You spent nearly 2k on the components, surely you can opt to put 3 fans on the bottom to let your 4080 breathe fresh air from the table top. side 3x120 intake (rad), bottom 3x120 intake (2x140 or 2x120 optional), top 3x120 exhaust, rear 1x120 exhaust

@JackNack-pz5wr

4 ай бұрын

For the radiator intake air draw, should I just flip the fan on the radiator to intake, or do I have to flip the whole radiator to intake?

@user-dk3bs1ft4x

4 ай бұрын

bro my pc is getting really warm it feels like a heater acctually with the case i really like it but i dont thing the pc really breathes at all since around is all covered with glass and also top wich force the airflow to be blocked in certain kind it keeps pushing the hot air of the aio radiator from the side cause i have intake from top

@WhyDidYoutubeDoThis

3 ай бұрын

@@JackNack-pz5wr Not sure I understand you, air flows through the radiator no matter what, the direction of the fans is all that matters.... and keeping the pump below the highest point in the loop.

@joelsantos662

3 ай бұрын

@@user-dk3bs1ft4x you have intake fans at the top? warm air travels upward so it's more natural to have exhaust fans at the top

@karimbouwmans983

3 ай бұрын

@@user-dk3bs1ft4x The fans should be pushing out. If you put an aio radiator on the side you need additional fans on the bottom to push cold air up.

Thanks for that, which alternative are you considering now?

Dude my radiator is like 38mm thick I mean I get I have some problem putting in but how is a regular 360 radiator having such issue?

I know this is 8 mo later but Cable Mod sells a 90 deg adapter that solves the cable hitting glass part. I just purchased this case and will probably go with this solution

@7.3dream95

Ай бұрын

Did you do that? How do you like it sir,

@bikedoc4145

Ай бұрын

@@7.3dream95 Yes they are great make sure to get the correct config they have some that the little wires are on top and some on the bottom depends on maker of your GPU and if it has the new plug type or not

How about H6? Will my zotac 4070ti tri-fan fit it right? Glass also touches the cable of H6 version of this?

It’s just not for you. I have this case, no problem with the cables touching the glass, this case is AMAZING.

Get a right angle cable. Now would you keep the case

I have just built in this case with a kraken 360 elite rad at the top and its fine. Close, but works just fine. Stunning case. Cpu (i7 13700k) 26c and Gpu 31c at idle with stock fan setup.

@samfan8685

3 ай бұрын

what are your fan setup like. Blowing directions?

Could you sandwich the AIO on the top slot for better clearance? Looks like there might be room between the bracket and the top mesh

@htpoint

Жыл бұрын

I did try that and there is no way to get the hose or cables in after as there is no opening.

@veaseyr

9 ай бұрын

Tried this with the Lian Li Galahad 360 AIO and it was too thick. I did however set up push-pull fans though. I put the Galahad 360 AIO fans on top of the tray for pull (not many fans have these specs for pressure through a RAD, so I need them for my i9-1300K). I set up Lian Li Infinity V2 Mirror fans on the bottom of RAD as push. On the side again I set up a push-pull on my 3080ti LC 240 RAD. I do wish NTXZ had left that 3/4 inch higher also to get the CPU cables through easier. But the two-thumb screw top lets you just move the RAD with all 6 fans up so you can get to the CPU connecter on the motherboards.

Sir, what is the graphics card used here. It looks stunning. Never seen such an arrangement before. Is it a casing for the GPU?

@teod5433

8 ай бұрын

founders edition

Thanks for this review!

@htpoint

11 ай бұрын

Thank you for watching 😊

Vertical mount the GPU, problem fixed. I didnt have issues with my Lian Li Gallahad 360mm. I did a push pull up top, and a 120mm in the back for exhaust, and 6 120mm intake fans.

@bluairsoft2671

10 ай бұрын

An even cheaper option that allows for the GPU to be horizontal would be getting custom cables that are lower profile or flexible. Seems like a chill thing to solve

Thanks so much for this info. Was aiming this case but not anymore 👍🏽

@htpoint

5 ай бұрын

Glad I could help

@neofoo

2 ай бұрын

what did you get instead?

@LittleAmbientMachine

2 ай бұрын

Didn't buy anything yet. Was going to build a new game PC but can't afford it @@neofoo

in horizontal gpu mount will it touch the glass in h9 elite as well?

can you tell me what is the better case?

I have some questions, like if i want to put a AIO 360 i can put on the side, top and down? And i will have problems mounting a 4070 ti of tuf gaming or a Xfx merc speedster 7900 xtx?

@user-dk3bs1ft4x

4 ай бұрын

side is best place yes dont put it on top cause the hot air coming out of it will be blocked on the top cause of the glass since there is only a small space for it to intake or outgo.. i had it like that before and the pc is like a heater it keeps bringging hot air in

@A7SkyHigh

4 ай бұрын

@@user-dk3bs1ft4x ty for the advice!

Is this compatible if I do Push and pull AIP configuration on the top mate?

@shanedutoit9101

5 ай бұрын

Apparently not. Havent tried it myself

1:24 you can also get a CableMod 1​2VHPWR 90 Degree An​gled Adapt​er

@htpoint

Жыл бұрын

Totally, I should have mentioned that, great call

@AdrianAichLF

Жыл бұрын

so his first issue is absolutely fixable, thank you

@bb1377

3 ай бұрын

This aged like milk.

Hi! Is this a 4080 founders edition? I'm not sure if my asus tuf 4070ti would fit in there without getting a vertical mount. The 4070ti is sligthly wider than the 4080 fe so even with the angular cable it could be an issue

@htpoint

Жыл бұрын

Yes this is the 4080 FE, if you are mounting it horizontally , something like a 180 Degree CableMod adapter should technically fit in, because it measures 21mm from the connector to the outer-shell

@user-dk3bs1ft4x

4 ай бұрын

yes it does i have an 4070 ti and it fit perfectly without vertical mounts

Great video, case looks amazing everything you spoke about doesn't bother me, big but is the power supply, it defo is gonna let out heat. So not gonna go for that case 👍🏽👍🏽👍🏽 Thanks

Does this case have preinstalled fans with rgb I´ve heard that it has 3 with rgb in the front and 1 without in the back right?

@shanedutoit9101

5 ай бұрын

Yes

@thestrangeminecrafter

5 ай бұрын

I know im really late but If you want the case to come with rgb fans then you need to buy the NZXT H9 Elite case as this is the case that has 3 rgb and 1 regular fan compared to the H9 Flow which has 0 RGB fans

I don't know what your talking about... this case is insanely good. Awesome temps, câble management , etc

@thekrat7769

4 ай бұрын

I think he is the lazy guy that wants the perfect solution that does everything for him (instead of experimenting and trying by himself).

I have this case with a 360 artic cooler mounted in the same place as yours but what makes this case awesome is I have it as push pull so it has hidden fans in the back and SL 120 inf in the front. The tight spot on the top I do agree I wish they had allowed about 3/4 of an inch more space there but the case has so much flow with the 13 120mm fans I have in it that top mounting the rad was pointless

@Goryglory0209

Жыл бұрын

Thanks Same rad owner and you comment helped me to decide to go for this or not

@gmacv3777

Жыл бұрын

Agreed. I do the same push pull on my 570X on front with 360 rad'

@gorkskoal9315

Жыл бұрын

who cares how fans look?. if you don't like the case because of bad materials, or the layout isn't your thing that's more important than having a fear of electronics showing in a fishbowl.

@hellhawk4680

Жыл бұрын

@@gorkskoal9315 what are you taking about ?

@inowtf4299

8 ай бұрын

@@hellhawk4680 I just copped the case what’s your specs bro?

Are you getting an issue with extremely loud fan noises in the bottom position too?

@htpoint

Жыл бұрын

Personally that wasn't a huge issue but there is a way to lower the noise for the bottom fans if you get something like a "Fan silencers if you google: Shakeproof Washer for 120mm Case Fan" its because these fans dont have any dampeners and it transfers all that noise/vibration around making them louder. But if you are getting the nzxt h9 flow I would definitely suggest getting some better fans something like the be quiet! Light Wings that would work nicely here or Noctua if you have the budget

I see a couple comments here asking what you ended up buying as an alternative or suggest as one. Ditto. Thanks.

Thanks for your Video. Did you saw Mr. Matt Lee's Video regarding his Asus ProArt build? He used the same case and put the radiator on the top. You can see in the video that there is enough space for the CPU power connection cables. The radiator thickness is the same (27mm). Not sure if the mainboard or the fans thickness is the issue here. As already mentioned by other users for the GPU you can use the cablemod poweradapter.

@htpoint

11 ай бұрын

I will check that out, was it the elite or the flow version

@brenner2297

11 ай бұрын

@@htpoint Flow version

@veaseyr

9 ай бұрын

My Galahad RAD measured 29.5mm thick and the fans that came with 25mm. The Lian Li flat-head RAD screws are just about touching with the fans.

I wanto build my first pc woth this case and I don't think I will need a radiator so would this case be suitable for my needs?

@htpoint

Жыл бұрын

For sure, if you are not planning to do any radiators, and just use air cooling than you should totally be fine, what GPU are you getting ?

@cipher8851

Жыл бұрын

@@htpoint a 3070 ti

You can buy an adaptator 90 degres to fix the problem with the graphics card

@xdoktor

10 ай бұрын

Just seen the vid and having just bought those same adapters @ 3 for 10 quid next day amazon I defo agree with you lol

I wouldn't worry about hte cables touching the glass, but I would invest in a GPU antisag support bracket. The one I went with is an L one that attaches ont he back pci slot openings, and is a bar that juts out underneath the GPU from teh back with a little rubber slider to go between it and the GUP near the end between the last two fans. It's a total b1tch to install but looks a lot better than the bracekts stand verticallyand wedge under the GPU and sti on top of your PSU shroud. On my Corsair 5000X the space between the top mounted 360 Rad and the motherboard was super marginal too. I made it work but man you have to do some finger acrobatics to plug those top mounted cables in and those two 8 pin power connectors in the corner. SO even with a differenet case you may run into the same situation. And yes I dvrsed plenty at Corsair but his seems to be some kind of weird normal. All they had to do was give me like one or two more centimeters between the top mounted rad and the botom mobo and life would of been so much nicer. The bottom of the motherobard has the same issue it goes right to the PSU shroud making plugging in those edge connectors a pain and an extra 2 cm would of been nice there too. I woldn't build in a new case after you did all that work, you're just making more work for yourself. If it works right now fine run run with it until your next big PC build in 5 - 10 years. It's not worth the hassle and headache just because a few things bug you. That's my 2 cents. The reason being, your eyes once yous tart working are always going to be on the monitor, not the case, and at home nobody is going to care about your case or how it looks. All yoru time is spent lookign at desktop pixels and not the case. That's why I'm goign to just leave out the RGB in my next build. It looks gorgeous pretty but goesn't really add any power to the comptuer.

I already ordered the case but thanks for this heads up. I think I'll get 90 degree cable adapters to mitigate the space issue

@JasonXBeats

4 ай бұрын

i heard those 90 degree cables are not good with gpu's

@TOO-LATE-qn4gn

4 ай бұрын

It’s fine the cable really shouldn’t touch the glass if they are plugged in securely and are tied in correct in the back with all that cable management junk all the other stuff is kinda just yapping the PSU shouldn’t overheat at all unless you got a crappy brand assuming you already got it delivered you probably know this all

@paddydoyle4694

2 ай бұрын

I have a 7900 GRE and it fits fine, cables don't touch, the 4090 is just a extremely massive gpu

Thanks for the review. Been using this case for a couple of months. Had the same concerns, the graphic card close to the glass and the AIO radiator so close to the top power cables. I am using an Arctic 360 rad on the top which is thicker than most rads. Managed to get the power cables in by bending them off to the left where there is a larger cut out for them to get through. The cables are very close to the fans but do not touch the blades, was concerned the first time fitting them lol. Think I will get the CableMod 1​2VHPWR 90 adapter in the near future, just to be safe as I do not like the cable hitting the glass, all seems fine and cable and connector temps are good but worth getting the adapter for the peace of mind. Happy with the case over all, very easy to work on. edit Going to leave the cablemod adapter due to the current problems with burning adapters and connectors, jeez!😶

@gezgez2

11 ай бұрын

had the same cooler and same issues in the o11 dynamic razer edition

@boastyy

11 ай бұрын

@@gezgez2 Thanks for sharing that George.

I don't understand why they don't make wider cases for these wide GPUs that have been out for a while now. Not everyone wants to pay more money and have worse thermals with a vertical mount

I miss the old scool cases which weren`t overengineered so much but had actual space for everything, everywhere. No matter which case you look at there seems to be always a part which makess you worry, will it fit? Will a bigger Power Supply fit? Will taller AIO fit? Will a bigger GPU fit? etc. etc. etc. Just make the entire cases slightly bigger in all dimensions and everything is solved. Oh and I would prefer a bigger focus on dust filtering and ventilation over glass pannels and room for RGB controllers and cablemangament "stuff".

@anon4854

5 ай бұрын

If you're not interested in glass panels and RGB then NZXT just isnt the brand for you. That's like going to a hotdog stand and saying you feel like a burrito. You're in the wrong place.

maybe they made the aio a tight fit so we buy nzxt aio ?

I’m just having issues installing my GPU it’s a MSI Ventus 2x 3060 if anyone has any tips that can help me they would be very much appreciated cause I am losing my mind with this

Can you not put the top radiator on top of the mounting tray and sandwich the tray with the fans underneath? Pretty sure that's why I'd didn't fit on top. Otherwise why would the top tray have a recess that looks perfect for the thickness of a radiator? Just my observation here. I mean no offense.

@htpoint

10 ай бұрын

Great question actually that would have been perfect but unfortunately it doesn't let you do that also no opening of any sort if you try to do that, I did try to do that. The Asus gt502 case that I reviewed has that option which lets you do that which is great.

@techandtoystuff

10 ай бұрын

@@htpoint then it begs the question, can fans go on top of the tray and it would have to be a pull instead of push?

@ric0h777

7 ай бұрын

I have the H9 Flow and a Karken Elite 360 and it is possibe to sandwich the rad up there. It is a tight fit, so taking the filter off would be best (you don't really need the filter anyway as air is being pushed out).

I installed Arctic Liquid Freezer II 420 in my H9 flow same as many other people

I choose to get the nzxt Kraken it works better and add additional fans from nzxt works to really cool but all check those dimensions before purchase

I'm not sure why you're having so many issues feeding those cables between the fans and MB, but looks like you have plenty of room.

@halrichard1969

Ай бұрын

What he didnt say or show is that there is actually the full thickness available at the back end of the radiator its about a 1sq in area that cables easily fit thru and are so close to the CPU sockets.

what is the maxium width that a gpu can fit in without issues?

Just built this with an RM1000x Shift PSU, Arctic Freezer III (360) AIO Cooler and a 4080 Super and everything fitted without any problems for me.

@mohammedtaoun6087

3 ай бұрын

Good to know I bought the corsair rm850x shift didn't even know that I bought the shift version tbh and was worried that hooking up the cables was going to be a problem

yeah I seen how narrow how that case is, you need a angled adaptor, which I personally want to have to use! so I will pass lol they need a re-design. if that's the 4080, I would imagine the 4090 is even more of a problem lol

The cable touching the glass might help keep it secured. I have the 011 dynamic and a Asus TUFF 4090. Cable touched the glass enough to support it but not mash it. using a fasgear 12vhwpr cable for 3 months worked great. Got the 90 degree adapter from cable-mod in march. Yesterday system randomly rebooted at idle and immediately reboot trying any dx 12 game. Tried to disconnect the adapter to re-seat the gpu and it's fused to the connector. I mean fused. Found the problem of the reboots. did a full clean install prior to rule out software issue.

does it come with a veritcal mount for the gpu?

@shanedutoit9101

5 ай бұрын

No

My buddy has the o11 and he has the same exact issues

isn't mounting an AIO with the tubes at the top of the radiator the worst way to mount it? water goes to the bottom and air goes to the top.

1:35 thats a VERY nitpick issue. It doesnt matter at all if the case does that.

I was gonig to buy NZXT H9 Flow until i saw this - what did you end up going with?

No offense dude but what are you doing is dual chamber if you didn’t know

Yea why would you stick a damn POWER EATER right there by the MB??? I thought it was bigger... LoL his GPU is bigger than the case.

*I have a 2700x stock air cooler and RTX 2060. * is this case overkill? or should i get the H7 RGB flow instead? this case is so beautiful 😭😭 but not enough RGB

@swoqix2892

6 ай бұрын

both of those cases are overkill for those components. the case is nearly the same price as your CPU.

@PCs454

6 ай бұрын

@@swoqix2892 but its the nzxt design i like. the H3 is a bit ugly to be honest ;-;

I guess I'm ignorant but i completely assumed it had some sort of RGB :( Every site shows nothing but RGB in pictures... Was super disappointed when i had to read fine print basically.

@notackerman

7 ай бұрын

Yes. The installed fans are not RGB.

just buy a vertical mount and enjoy the case, why would you horizontal mount a gpu in a case like this....?

So what you recommend

@htpoint

10 ай бұрын

The nzxt h9 elite, will definitely have more room at the top, what kind of component's do you have ?

Well after watching the whole video I think I'm gonna go for Lian li O11 Evo . In that the power supply is in bottom so no heat transfer to motherboard.

@Singh.Manjeet

10 ай бұрын

did you get your evo ? I found evo is not have filter so problem for a place with dust.

@dronzer007

10 ай бұрын

@@Singh.Manjeet Neither, for now I went for 216. Will buy the new O11 when it releases later this year.

@thang8868

10 ай бұрын

@@dronzer007 hello, the new case lian li 2023 will be update later this year ?

thabk you, I consider Corsair 5000D Airflow...

This must be his 1st PC build. Everything he mentioned is what a newb would encounter....HAHAHAHAHA

This case is bought already if it didn't work out for you it surely did for thousands I wonder 🤔 why.

Nice view tnx

so what this guy is saying if you have a 4090 get a mount

It's a no for me. PSU location is so the worst ever.

Get a proper power supply and you will be just fine.

NGL it’s always that one video that’s say never buy this why

The second i saw you scared of a wire bending i knew you were full of crap 😂

I’ve been waiting forever for mine to ship 😢

@OfficialTechMinute

Жыл бұрын

Where did you order?

Just seems like a h6 flow with worse airflow to me

NONE of your issues with this case are an actual issue. man up!

So vuy a gpu power adapter and thats it

bro just wants to be different

Your returning it but they're all simple fix 😂 wtf

sounds like skill issue

This was a waste of time. It's a guy complaining about things that aren't really an issue. Saved ya 5 minutes.

I don´t care, I bought it already.

@htpoint

11 ай бұрын

I would go with the elite version which isn't going to have some of these issues at least the top radiator issue.

@Singh.Manjeet

10 ай бұрын

@@htpoint but it has a top glass which is kind of blocking air... again a issue

You moaned about a load of things that are not a problem. NZXT offers the vertical mount for the larger GPUs for a reason. How can you moan about something that has been thought of in the design, when its your own installation failures that are problem. Get a grip. Wasted my time. Stupid review.

Review is biased towards NZXT, I hate this reviewer, I have seen plenty of other reviewers who actually like this case and excited about it due to it being out of stock. garbage review, u got tooooo many negatives.

Fatherless activities