DIY Tooth Bar for Compact Tractors
Тәжірибелік нұсқаулар және стиль
Easy way to make your own tooth bar for your compact tractor. All you need are shanks, teeth, and flat bar stock. Its easy to weld up your own tooth bar to easily dig into compacted soil and the cost savings is huge compared to buying a pre-built tooth bar.
Teeth: amzn.to/2Vgq9B3
Пікірлер: 50
What a great idea,I would much rather have your tooth bar than a store bought one. Great job Sir! Butch Ashland Ohio
@appalachiandiy2415
Жыл бұрын
Thanks!
Great job my friend!
Nice welding!
@appalachiandiy2415
Жыл бұрын
Thank you!
Thats a pretty cool setup, saves drilling 2 holes per tooth in your bucket! Thanks for the great video!
@appalachiandiy2415
2 жыл бұрын
absolutely! only two bolts holding on the entire bar.
Excellent video, I think I have a new project for my LX. Cheers
Thanks for the great video. Been debating between diy like you built or a piranha. Nice welds too.
@appalachiandiy2415
2 жыл бұрын
Thank you. I like the DIY bar because of the tooth length and replacability. the Piranha's are nice though
Drill bit trick is awesome. Kinda mad I didn’t think of it. Used it already in the shop.
@appalachiandiy2415
3 жыл бұрын
Yea! otherwise its soo difficult to measure how thick the plate needs to be
Outstanding, subscribed!
@appalachiandiy2415
2 жыл бұрын
Thanks!
Nice job looks good
@appalachiandiy2415
2 жыл бұрын
Thanks!
Great info brother
@appalachiandiy2415
2 жыл бұрын
Appreciate it!
I almost did this but the shanks and teeth together would have been the same as a tooth bar from vevor. I had to modify for my application. Did a video on digging with it vs the smooth bar.
@appalachiandiy2415
2 жыл бұрын
I havnt seen a tooth bar with big teeth like I used on a bar for a tractor this size. Are the ones from vevor excavator teeth like the ones I used here?
I REALLY need to learn to weld...
@appalachiandiy2415
3 жыл бұрын
It opens so many possibilities! I would definitely recommend you learn.
Good job but advice from a pro welder , you should have started from the front of the tooth and not left crater in the front where all the pressure is gonna be , did this hold or did they start cracking where the crater was ? I’d say with how the tooth went on will help you with the crater not breaking
Great video, thank you! Would you please link where you bought the teeth. TYIA.
@appalachiandiy2415
3 жыл бұрын
Yep, I just updated the description with a link
Thanks for the video. I have been debating on making my own. How easy is it to remove? Is there anything you need to watch out for not to bind so you can get it back off?
@appalachiandiy2415
2 жыл бұрын
I made mine tight. Could have made it with 1/8 or 1/16th less in bar stock thickness. Other than that not really
what is a good supplier for the shanks and teeth for this build ?? I would like to build one of these for my tractor .
@appalachiandiy2415
2 жыл бұрын
I got mine off amazon. Check the discription below
This a great video! You’ve inspired me to build my own. And super good welding. Do you have the source for the teeth and shanks?
@appalachiandiy2415
2 жыл бұрын
Yes, there is a link in the discription
@happyrecluse2849
11 ай бұрын
@@appalachiandiy2415 Real good vid, those teeth are at this point, unavailable and undetermined when will be.
Where did you get the 5/16" steel flat bar from ? Thanks
@appalachiandiy2415
2 жыл бұрын
From a fab welding shop. T D Fabrication. Clearfield, PA
@MasonrywithAL
2 жыл бұрын
@@appalachiandiy2415 Thanks for the fast response ! Subscribed
@appalachiandiy2415
2 жыл бұрын
@@MasonrywithAL thanks for the sub
Wish I knew how to weld.
@appalachiandiy2415
2 жыл бұрын
Its probably one of the handiest skills to have. Best advice I can give you is go buy a used/cheap welder and watch some youtube. Formal training is great too if you have a tech school near you
@michaelc9128
2 жыл бұрын
@@appalachiandiy2415 if one does not know how to weld most areas might have a mobile welding guy that can help a person out or take the loader bucket off the tractor and take it to a local welder
Price of that vs buying a prebuilt one?
@appalachiandiy2415
Жыл бұрын
All depends on how cheap you can get the teeth. Thats the most expensive part. Most store bought ones dont have as big of teeth either.
@daddio7249
Жыл бұрын
Titan Attachments has kits, look on Amazon. Unless you have a local source flat bar is difficult to find. I got a 48"x2"x.20" from Amazon but my John Deere's bucket is 53". They only had one so the next closest thing was a 36"x3"x.12". I got a set of five mini-excavator shanks and teeth. I placed the 2" on the cutting bar of the bucket and tapped the shanks on, they fit perfectly. I welded the shanks on the 48" bar and cut the correct length pieces of 3" to extend the bar to 53" and make the bolt on ears. I welded those on and the used a cobalt step bit to drill two mounting holes on each side. My 23 hp tractor is not powerful enough to damage the bar. The Titan kit comes with a thicker bar and precut mounts. Price is about what I paid.
1st!!!... From The PHILIPPINES!!!...
@appalachiandiy2415
3 жыл бұрын
Nice! a little over 8000 miles away!
@fmainternational4210
3 жыл бұрын
@@appalachiandiy2415 Yes Sir, 12,874.75 Kilometers!!!... We use Metric Measurement here in the PHILIPPINES!!!... It's the International Standard of Measurement since 1980!!!...
@appalachiandiy2415
3 жыл бұрын
@@fmainternational4210 someday the US will get on board with everyone else haha
@patriotriderfromhell8130
Жыл бұрын
@@appalachiandiy2415 yeah, but our good ol' SAE has worked for eons and it looks like we still kinda like it...A LOT😊
@patriotriderfromhell8130
Жыл бұрын
And Thank you for the excellent video. What model Kubota is yours?
Sir my factory specializes in the production of excavator forging bucket teeth ! Hope you can contact with me !
@appalachiandiy2415
2 жыл бұрын
you can contact me at AppalacianDIY@gmail.com