My uncle in Tennessee had a huge version of that. I don’t think he was distilling salt water, though.

@johnosman8971

2 жыл бұрын

Any type of distillation processing has advantages over simply being able to just stop at a pond, creek, or whatever sized body of water you are attempting to get a potable water source from, … be it with the previous type of distillation process shown here, … or such as a chemical, or padded filtration system, … shoot, you can sometimes distill water through a sand trap, where you percolate the water through a significant amount of sand grains, that can sift out any contaminants through a medium of the sand used, … it may take several attempts to clean a specific amount of sand, to rid it of any impurities itself, but, with each pass, through the grains of sand, it becomes more pure, … the best situation, would allow, for whatever impurities being sifted from passing through the layers of sand, to not disturb the grains, at the bottom of your”trap”, thus giving you a much cleaner amount of potable water, … and you should also, boil your water source for approximately 20 minutes, to get rid of any untoward bacteria strains, …

@sameer19871987

2 жыл бұрын

Shine!

@ffemtx47

2 жыл бұрын

@@johnosman8971 👈 Joke went right over his head. Left tire tracks on his forehead like a John Force funny car leaving the line...🤣🤣

@750suzuki7

2 жыл бұрын

I would have to taste a few gallons to be sure that it isn't salt water. Send it over right away.

@privateinformation6082

2 жыл бұрын

😏I saw it and thought damn that’s small and convenient and then read the title

A lot of steel water bottles have a non-stick coating inside. Also important to make sure that yours doesn't before boiling water in it.

@nicklopez7536

4 жыл бұрын

This is very important and should be mich higher up in the comments for more people to see and for NightHawk to see as well.

@nicklopez7536

4 жыл бұрын

This is very important and should be higher up in the comments for NightHawk and others to see because steel bottles indeed have coatings on the inside.

@SapphFire

4 жыл бұрын

+1 (Replies seem to push comments further up)

@davidburke4101

4 жыл бұрын

Yep

@gulktroktet

4 жыл бұрын

There's no point in trying to remove it. Just buy one that doesn't have one.

I would recommend using only stainless steel parts. Copper in contact with distilled water oxidizes quickly and this oxidation contaminates the water. Another tip is to leave dolomite tablets in contact with water for a few minutes to raise the ph and recover magnesium and calcium. We also have to be careful with excess boron in desalinated sea water, sometimes the steam pressure drags the boron. I prefer to use brackish water.

@katatoth7551

Жыл бұрын

boron and magnesium are very important minerals. if one does not have them tooth decay and bone problems will appear.

@Tommy.OrginalvideosPhilly

Жыл бұрын

Well said both of you

@VantageWelding

Жыл бұрын

Both you guys kick ass. Thanks for these tips

@blackouting

11 ай бұрын

😱😱😱

@blackouting

11 ай бұрын

@katatoth7551 I'm not sure what Boron is... i know what Borax is, though, but something tells me I shouldn't eat it 😅

Good trick during the ad, using the cute bird as a lure while you talk on! I salute that subtle yet effective trick.

If you use an open fire to cook while camping; you can use bar soap and splash of water to coat the outside of the cookware in a thin layer. This will allow the soot from the fire to be clean off very easily when finished.

@DR-bp1yu

3 жыл бұрын

Great tip, thank you. Another option would be to wrap the bottle in tinfoil or aluminum foil. A soda can can also be sn effective sleeve. The steel in the bottle would not stay pristine though, as the heat will induce a color change. But it will not be covered in sooth, which is much worse. Once the bottle cools enough to touch, you can use a mix of wood ash from your fire and a bit of your clean water to make a nice cleaning paste, it will scrub the bottle nicely without scratching it.

@chloedemeter5473

2 жыл бұрын

Thin layer of mud works ok too. Just enough to coat it, too thick and it'll quickly crack and fall off in big pieces when it dries.

@Bwanar1

2 жыл бұрын

Someone payed attention during old school Boy scout training!

@Palemagpie

Жыл бұрын

Washing-up liquid is better. It's entirely non-flamable unlike some particular bar soaps. And even if you really burn the crap out of it. Still water soluble. So it just washes clean off.

@inashamsia

Жыл бұрын

woah great tip!

This video is so calm. It's a nice break from the constant excited energy of youtube. Even channels like yours are hyped and energetic.

@whuzzzup

4 жыл бұрын

100x this.

@benjaminmiller3620

4 жыл бұрын

You like calm videos & survival? Check out 'primitive technology'

I was once lost in the woods and I had a compass, but all I could do was draw circles.

@SF-li9kh

3 жыл бұрын

Lol. That compass 😂

@Whiskeybuisness

3 жыл бұрын

LMAO..😆😆

@PatrickKQ4HBD

2 жыл бұрын

Take your thumbs up and get out!

@ndudgczufofuf6270

2 жыл бұрын

Lol🤣🤣

Something to keep in mind with this, stainless steel when heated to a certain point creates chromium carbide. This is bad, when the chromium has been reduced to a certain point stainless steel begins to corrode. You'll see it when stainless steel begins to show purple bands in it, that means it's too hot to maintain it's resistance to corrosion.

@buffplums

2 жыл бұрын

Wow that’s good advice …. Wonder if there is an alternative way to make something like this ? I don’t suppose Aluminium could be used, apart from the risk of melting it but would there be a contamination risk from that also? Maybe that would be ok as we cook with aluminium pans.

@Axel_Andersen

2 жыл бұрын

@@buffplums We also cook with stainless all the time year after year. Yes this chromium corrosion is a thing but not in this contex and temperature. As long as there is water inside the bottle the temp can hardly rise above 100°C because this is not a pressure vessel. And because it is not pressure vessel corrosion is not a thing, it would only cause it to leak, not likely to cause any problems.

@simplekindofman6265

2 жыл бұрын

Would tin be better for water distillation I’d like to make one for camping long term So I don’t have to carry water

@megastick9324

2 жыл бұрын

At cooking temperatures it’s not an issue. The hexavalent becomes an issue when heated to melting, such as welding, and then it depends on the process. Stick welding releases hex. Chrome, however, tig welding keeps any release within acceptable safety margins. This from a professional welder. We never heard a thing about hex. Chrome until just around 15ish years ago. Now, when stick welding we need respirators, not so with tig. After many years of never having been told about it and God knows how much intake.

@mestrone

2 жыл бұрын

Do you happen to know if the copper releases any harmful substances as it may on alcohol distillation? I have read about copper poisoning when boiling on copper kettles, but what about steam passing through it?

i absolutely LOVE your little bird friend!

@Nighthawkinlight

4 жыл бұрын

Me too

@holymegadave

4 жыл бұрын

With a pen saber hehehe

@MichaelHarto

4 жыл бұрын

The bird is cute no?

@J0ermungand

4 жыл бұрын

Suddenly I too want a bird :P

@OldGamerNoob

4 жыл бұрын

is that the "night hawk"?

what i like about your videos is that they are high quality. and it seems that you dont care about the algorithm favouring frequent uploads at the cost of quality. I also like how we can actually do what you do.

@DanHaiduc

4 жыл бұрын

The algorithm favors clickthrough rate, according to Veritasium. And who wouldn't click on a video with such a title?

@dominicrichardson5546

4 жыл бұрын

Agreed, so many projects from other youtubers require expensive workshop tools or materials, but these projects are wonderfully attainable

@whuzzzup

4 жыл бұрын

He didn't even make it 10 min. Good guy.

Your bird is so playful, he's very comfortable with you. Good addition to adverts, gives something to watch so the ad doesn't get skipped.

It is important to keep the copper clean as it will oxidize along with picking up a black substance that is more dangerous. The best way to clean is use citric acid solution and then rinse well. Some will rinse with a 50/50 vinegar/water solution followed with straight water.

@rsnell22

5 ай бұрын

Hmm. Like the oil cooler on an old 19DA where the water chemistry wasn't kept up with. I, too, would use stainless.

@ecr1023

Ай бұрын

Copper is used in Espresso machine boilers. Just use a standard descaler or vinegar solution.

This is the sort of advice that is almost entirely pointless to know .... right up until the moment when it will save your life. Brilliant video. Thank you.

@diggydude5229

4 жыл бұрын

I think it's good to know this sort of thing *before* you need it. You may not be able to google it in a survival situation.

@seanmack28

4 жыл бұрын

Like now. Lol

@RuralTowner

2 жыл бұрын

@Predbeau101 Right in the same category as "Dying of thirst while watching another drown."

@RuralTowner

2 жыл бұрын

@Predbeau101 On the latter...I know. The former...forget where I heard it but I think it had to do with being stuck on one of those (very) small islands & dying of thirst yet are surrounded by undrinkable water that you see another drowning in.

@jojoemcgeejoe457

2 жыл бұрын

@@RuralTowner Water Water All Around And Not A Drop To Drink.

I love that you show the trial-and-error and 'failed attempts' during all of your projects. Most representations I see of science/engineering in movies/tv/other media just show the idea→final product and I think it gives a false impression of what this work actually requires.

Never tried it, but filling pipes with sand before bending them, helps to keep their shape regular, especially with larger diameters and narrow bending angle

@Den3productions

2 жыл бұрын

I wish I would have read this comment two weeks ago!

@shorebird9

2 жыл бұрын

fill the tube with water and freeze it. The ice/water will not compress thereby maintaining the tubes' volume.

@stopthephilosophicalzombie9017

2 жыл бұрын

@@shorebird9 clever

@stupidscruff5794

2 жыл бұрын

@@shorebird9 the pipe could snap if you do that

@bretk7916

2 жыл бұрын

The sand will just move and be pushed out of the pipe and if you seal it so it doesn't do this then it will just compact and make it impossible to bend or split the pipe like frozen water does to house Plumbing when the expanding water that's turning into ice has nowhere to go

Really cool! Back in the 60s/70s, my dad used to make me little steamboats using this sort of technique.

Wow there is a real DIY, not a comercial profesional tool used, just regular cheap ones everyone got at home thanks!!

@Misha-dr9rh

4 жыл бұрын

"cheap ones" >drillpress

@onemangamer587

4 жыл бұрын

@@Misha-dr9rh can use a hand drill or electric drill, just a matter of time and precision

@ryanhelmbold2288

3 жыл бұрын

I dont think most people have solder, flux, and a soldering iron though

@cidizzle

3 жыл бұрын

@@ryanhelmbold2288 copper soldering kits are like $20 and if your home has copper pipes will help a ton if your pipes spring a leak and flood your kitchen at 4 am. Ask me how I know.

@gus473

3 жыл бұрын

@@cidizzle Propane or MAPP gas....? 🤔

Spreading the copper coils apart will lower the amount of heat one coil will transfer to the next. It allows cooling air or water to reach all sides of every coil. I like your design. Very compact and usable.

@brianh.000

4 жыл бұрын

Good idea--should improve the heat sink abilities.

@Anthropomorphic

4 жыл бұрын

Might make it harder to fit them in a water bowl, though.

@michaellinner7772

4 жыл бұрын

You're right except coiling and uncoiling it over and over would quickly fatigue the copper tubing eventually causing it to rupture.

@wraithgear4216

4 жыл бұрын

@@michaellinner7772 i assumed he ment to stretch it out just the once. Or even trim the length to spread it out permanently

@diggydude5229

4 жыл бұрын

True, but you would presumably want to wrap as much copper around the bottle as possible to provide a longer cooling path. There would have to be some trade-off between length and coil spacing, I guess.

Adding flux before your solder piece might keep things in place a little easier. I think it helps the solder adhere better as well.

@kensmechanicalaffair

11 ай бұрын

Yea, that iron would of gotten hot enough to ditch the torch.

Good demo and video. My thoughts for improvements while I was watching it were: 1) it would be good to be able to adjust the height of the bottle to control the heat; this could be just a knot in the rope, or other device, and 2) you could stuff the damp cloth inside the coil, instead of draping it overtop. Better yet, have a vessel, like your food mug, just the right size so you can immerse the coil in it.

Oh man, you just can't stop improving, can you? I've been following you since airsoft video.

Spacing out your coils. So the air can get through them. As well with the heat dissipate

@wlcm2grvit

4 жыл бұрын

It won't explode, the tubing is opened to atmosphere. One could experience some mild water hammer from steam bubbles collapsing within this set up but as he demonstrated with immersing the coils in the pot of water, this effectively created the heat exchange necessary to get steady condensing

@ToxicallyMasculinelol

3 жыл бұрын

@@Santa-614 explosive release? what a joke lol, it's a fucking tube with a hole on one end

@sikox2098

3 жыл бұрын

@@ToxicallyMasculinelol I’m pretty sure he meant it hyperbolically, and what kind of tube doesn’t have a hole lol😂

@_Anthony___

3 жыл бұрын

@@sikox2098 a rod

@sikox2098

3 жыл бұрын

@@_Anthony___ a rod isn’t a tube🤦🏽‍♂️

This is absolutely brilliant and quite possibly the single most valuable diy survival sustainability video I've ever seen. Good lord man, thank you for this one.

@user-pm8je4fo7e

Жыл бұрын

Yeah, if your "survival" plan implies carrying around two extra kilos of tubes and a wrench. This setup is good for making water out of piss at home. Executing it outdoors on a daily basis would be too much pain in the ass in comparison with old ways.

@lit3plumber12

8 ай бұрын

I can't agree. Only a small portion of land is next to saltwater making it practically useless for me and a lot of other people. And even though I agree it's worth it's weight to carry, a life straw is a much cheaper option and might even last longer. Great if you're surviving near the sea or on a flame proof boat.

@clark5363

8 ай бұрын

@@lit3plumber12 I live on a peninsula surrounded by ocean. I have other stuff for freshwater, which there's not a great deal of anywhere nearby. Otherwise sure. Lifestraws are fantastic.

Thanks for the super-practical video that doesn't require a lot of expensive parts or equipment! Sweet!

This will be very useful in the coastal communities of countries that are frequently hit by typhoons/hurricanes/cyclones as this lets them get drinking water from the ocean...

@boriscat1999

4 жыл бұрын

desalination plants are very common in desert regions near seas. They are very energy intensive compared to simply pumping clean water out of the ground from an aquifer.

@NGC1433

4 жыл бұрын

i hurt my brain trying to imagine a community advanced enough to watch youtube, but stone age enough to be unable to figure out water desalination on their own. youtube roaming chimps?

@muhammadizzhakimbinramli3431

4 жыл бұрын

@@NGC1433 i think that's why OP mentioned that the communities had to be disaster proned cause then they could get fresh water during disasters

@cjmpaja

4 жыл бұрын

@@muhammadizzhakimbinramli3431 yup. when a natural disaster strikes, the things that we normally take for granted (ex: electricity, flowing water, communications) are not always available. Have you experienced having no electricity, running water, internet, and telecommunications for a few months straight? Hence this device is useful during the aftermath of a natural disaster, when the government has not yet got supply lines up and running...

@kickAssScience

4 жыл бұрын

@@boriscat1999 Are you delusional? What often comes out of the sky in those parts of the world?... rain

I've been tinkering with water distilling for a few years. Just rewatched your video and love the tip about submerging the coil. Awesome video... I love your projects.

@JohnSmith-sj7io

Жыл бұрын

Thinking of building a large one myself. What would you recommend measurement wise for production rate of a 10 gallon pot.

Pretty cool. People who live on ocean coastal areas may need this someday. Thanks for posting.

I HAVE SEEN QUITE A FEW DIFFRENT DESIGNS -YOURS IS THE MOST SIMPLE AND PRACTICAL TO CARRY IN BACKPACK

All I would do is make the distance between the coil and flask greater to maintain the differential or shield the coil from the heat source with anything reflective or something insulating and not too flammable like bark. I doubt, however, this would improve function by much. I'm always happy to see your videos pop up, thanks.

@Mr3344555

4 жыл бұрын

There's no purpose, if the whole concept is to be compact, your design change is going against it. It also a non functional Destin change, so no need.

@jimphubar

4 жыл бұрын

@@Mr3344555 If you would kindly reread my comment you'll find we almost agree. The 'purpose' is to desalinate water by way of distillation using a compact unit. Distillation works by creating a heat differential between the evaporator and the condenser. Therefore increasing the temperature difference will, necessarily, improve function. The inverse-square law means that a small distance further away will have a seemingly great effect on said differential. Adding an extra few centimetres after the condensing coil will hardly make this a bulky item. Equally, it would be little effort to shield the coil from radiant heat. The bit I think you missed was.."I doubt, however, this would improve function by much." J.

@animefreak5757

4 жыл бұрын

the length of the coil plus the straight bits is already almost the length of the bottle. You could save a bit on the water outlet and move it to the steam inlet though.

I normally quite like your conversational style in your more science-based videos like the gasifier, but this is a perfect example of how to do an instructional video. No unnecessary flimflam, no tangents, just "these are the parts you'll need, this is how you build it, this is how you use it". Great stuff (and a very neat looking finished product as well!)

Thanks for sharing. I saw another video where they took a pot of water about 1/3 full, put a bowl in the middle, then set a curved pot lid on top except upside down. The boiling water condensed on the lid and dripped into the bowl. Probably the simplest system I have seen.

@williambrandondavis6897

7 ай бұрын

that's the old 90's method for iso hash. lol

A connection tube about 8-10" long or so to connect the bottle and the cooling spiral could give 2 advantages: - more distance between the cooling spiral and the heat source under the bottle - the connection tube could have a knee that brings the winding of the coil in horizontal position. Open the coil (separate the windings about 1/2 inch to each other) also helps the condensing water rinse out the tube. Tat helps keeping pressure in the boiler constant, so You'll have less "boil over".

Finally, I can make moonshine on the go.

@m3dia95

4 жыл бұрын

king koda I was thinking poitin too haha

@n017kingg7

4 жыл бұрын

was thinking the same

@wilfordownbey5000

4 жыл бұрын

"I don't think so Tim". #AlBorland

@kidathi

4 жыл бұрын

😂😂😂😂👏👏👏

@spambedam

4 жыл бұрын

Yer gol dang right!

Pure Michigan: "I am surrounded by freshwater seas. I should make a video about a compact desalination rig." Your videos are a joy to watch, and I certainly hope they help lots of people be safe. Which I am pretty sure is why you make them.

Instant favorite. Your design is amazingly simple and effective. I know what I'm adding to MY survival kit!

@richardaversa7128

2 жыл бұрын

You wouldn't by any chance be the kind of guy with a survival kit but refuses to wear a mask?

@richardaversa7128

2 жыл бұрын

@Tai Chi Tube what the good baby jesus are you taking about my man

This is great. Watching youtube can be very helpful for us city slickers adventuring out into the wild.

Came for the portable desalination bottle method, stayed for the bird. Adorable.

@kamikaseiken5774

4 жыл бұрын

True

@gtbkts

4 жыл бұрын

Darren Henley same. Lol

@gutspraygore

4 жыл бұрын

Yep. Me too.

@warlikelaughter6230

4 жыл бұрын

Me: so that's why i shouldnt drink distilled water..... wow, what an easy solution 🙄 just add a drop of the concentrated salt water into the distilled water... hrmm yumm?? DAAA BIIIIIIRDYYYYYY!!!!! 😀😃😀☺

@TruAnRksT

4 жыл бұрын

I agree that bird was adorable. Reminded me of my cats.

Thanks for a great Video! The bottle in fire automatically turns to black, but that's a layer of tar, which is poor conductor. If you use flame blackened kettles on fire, they are less efficient than clean ones. So, if you look forward to boil the water with solar energy, i recommend to find some special paint for that, instead of tar layer. 😎👍

@PBMS123

4 жыл бұрын

​@Anonymous Anonymous No he means tar. Because this is being heated by the burning of plant material, it produces TAR, and Carbon. If it was being heated by hydrocarbon gas, like a propane, it would be carbon. But using wood, or other plant material causes tar. Just like Tar in tobacco. Which is why even cannabis produces tar, and in some cases in higher amounts than tobacco.

@PBMS123

4 жыл бұрын

@Anonymous Anonymous they are not solelely hydrocarbons dude. Otherwise the byproducts would just be carbon, carbon dixoode and water. But they aren't. ALL PLANTS produce tar when burnt. That black stuff will be carbon and tar. en.m.wikipedia.org/wiki/Tar_(tobacco_residue)

@rohzpopper4922

4 жыл бұрын

Just wet the entire bottom with cooking oil,no need to paint. After finished boiling with open flame, the black soot bottom can be easily wipe off.

@Morio412

4 жыл бұрын

@@rohzpopper4922 What I did with my mess tins when in the military was take a bar of soap and rub that on the back bottom and sides before cooking. Leave a nice coating of soap and its really easy to wipe off and clean when finishing cooking/boiling water.

@TheOMAha94

4 жыл бұрын

@@rohzpopper4922 Thanks for the tip! 👍 I'll use that in my journeys coming.

Outstanding project and as you mentioned concerning suggestions my suggestion to you is a deeper much larger pressure cooker can be used, for larger amounts of water!

I love these types of video nice to see someone making useful and interesting projects

Great piece for the kit. Minor point : heat first, then flow solder.

@kckeithc

4 жыл бұрын

Exactly, that part was tough to watch. Lol

@honor9lite1337

3 жыл бұрын

@@kckeithc can you explain it to non-technical person?

@prielknaaphofnar.9754

3 жыл бұрын

@@honor9lite1337 You heat the area where you will solder beforehand, then add the solder with heat to ensure the solder binds to the metals.

@honor9lite1337

3 жыл бұрын

@@prielknaaphofnar.9754 much appreciate it. 👍

@rong1924

3 жыл бұрын

@@prielknaaphofnar.9754 My water soluble paste flux burns black before the silver solder melts. I can't get the stainless tinned for the life of me. Any suggestions?

Its a great design for a portable distillery though and I thank you for sharing it with the public. I commend your work and I believe you are doing a great job of presenting important material to your viewers. Thank you again

@davidfuller764

2 жыл бұрын

Me too!

So much effort. My cheap and cheerful method is an old metal camping kettle and a piece of rubber tubing. One end of the tubing is pushed over the kettles spout and the other end of tubing goes into a bottle or container.

For anyone having trouble soldering the copper to the stainless steel (it can be tough to get it to stick and not just bead off), Ruby Fluid Stainless Steel liquid flux is great for that. Apply it to where you need the solder to go, heat up the parts, and apply the solder.

your CO Host steals the show.. and MY heart

honestly if you made a kit with everything including the stove I would buy it in a heartbeat

@paulduggan2

2 жыл бұрын

Same here… just take my money already!!!

@andrewj22

Жыл бұрын

That's what I came here to say! Make me one, please!

1. Try a bottle with a lid that goes all the way to the outside of the bottle, and a liner. Can remove liner and use it to catch distilled water. Place the liner back in the bottle for storing freshwater so you don't have a salty taste. 2. If enough space, can place coil between this liner and metal bottle. 3. Since the temp should not exceed boiling temp, can use plastic tubing instead of copper. 4. Use screw fitting rather than soldering - soldering can break down at high temps. 5. Use the tubing for the bend rather than a fitting to drop weight. 6. When buying fitting, also buy an endcap so it won't spill water when using for water storage and not distilling. Leave fitting on tube rather than relying on compression for easier change out. 7. Installing copper wool in the tubing increases condensation (more contact area for water droplets). 8. Burn inside of bottle thoroughly to remove any lining. 9. If hard to remove gasket, buy 2 lids - 1 for distilling without gasket, 1 with gasket for water storage.

@1SCme

2 жыл бұрын

@Tai Chi Tube They're already using copper tubing. It's fine - the amount of copper you would need to ingest to be toxic is substantial (above 10 mg a day) - to put into perspective, this is about the same as 1 inch length of 1/4" copper tubing in a month - you wouldn't lose even close to this much after continuous use for years. You would want to check the plastic type, but it is commonly used in food processing at home and at manufacturing plants. If you're searching desperately for a problem, you would note the low thermal transfer of most plastics... but concern with copper is a desperate reach.

Your worm (copper coil) should always be going down hill. As you have it the distillate will pool up inside the worm causing resistance and spurting on the output. On a larger scale, would cause a dangerous over-pressure in the boiler.

@davidmcduffee1167

Жыл бұрын

Doing that would make a liquid-filled cooling container more difficult, as the coil will need to come out the bottom of it. I'd rather put up with the spurting and have a system that's simpler to build.

@ralphm6901

5 ай бұрын

@@davidmcduffee1167 just a thought - If one end of the pip is brought back down to the other end, the coil could be hung upright with the open ends at the bottom. Blow steam into the side that goes straight up to the top of the coil, then water will dribble down around the coils to the open end. That also make the whole coil available to drape a wet cloth over Or even have a secondary steel bottle left inside the coil to dump cold water into for cooling.

You mentioned the solder weld, and your best results "gentle heat" - what's more likely is that you've heated both parts consistently, to the melting point of the solder simultaneously. This has been my experience. Heat both piece up slowly so they reach the melting temp at the same time, and then apply a little more heat until the solder "wets" and wicks up the parts, remove heat and let the joint cool on its own.

@burnerjack01

3 жыл бұрын

Or could compression bulkhead fittings be used? Just a mechanical joint secured by nuts on either side of the lid. Using a hole just big enough to be able to force the tubing through. Might leak a little but so what? An even easier construction method as there is no torch involved. Haven't tried it, just "thowin' it out there".

@Bubu567

2 жыл бұрын

And don't try to speed up the cooling with water. It will just cause the steel to pull away from the solder.

@ScienceDiscoverer

2 жыл бұрын

@@burnerjack01 Also this will be more corrosion resistant, because heating up stainless steel makes it corrode.

I recommend that you reroute your copper coil outlet (since it's flexible enough) to be dipped at the bottom of the beaker to avoid lost steam and efficiency. Great video.

@DingleFlop

2 жыл бұрын

6:53

@LDR33Pyrodyne

2 жыл бұрын

A short length of silicon tubing thrown inside would do, wouldn't it? Then you wouldn't have to bend the copper back and forth

@meejmuas8686

2 жыл бұрын

He could just extend the copper tubing and have it bend at an arch to a point where it can touch the beaker at the bottom

Muchas gracias por compartir tan Valiosa información de Supervivencia! Fuerte abrazo desde la Ciudad de México!

This is one of my favorite videos, and I've watched it probably a dozen times. I've designed my own two-bottle system based on your design here such that I can easily pack it during a bike camping trip. I'm working on making an activated carbon filter system using the same bottles too so that I can create a sort of ad hoc water station setup if needed.

@Nighthawkinlight

3 жыл бұрын

If you're using it regularly watch out that any copper pieces don't corrode as the green copper salts are mildly poisonous. If I were to make this again I would use only stainless steel, no copper or brass.

@winkfinkerstien1957

2 жыл бұрын

Would it be more difficult to coil stainless steel tubing? Could you do a Version 2.0 video with all stainless steel material?

Love your design and your video format. You do a great job with your ads too, I actually want to keep watching even though it’s an ad.

Great video as always. Well explained and simplistic design for ease of making. A few recommendation for improving this project is to find an alternative to the small rubber stopper, as this will most likely be easily lost due to its small size and time it takes for distillation/ long time being a loose piece. If possible i would suggest something like a simple valve attached to the elbow and before the copper line fitting. secondly having a parts list either in the video description or shown in the video will help people recreate it as they wont need to search through the whole video for where you mention the piping size or type of vessel used. lastly a small safety tip for distilling water: if the water source is contaminated with chemicals or heavy metals (you may not know in a survival situation), it is good practice to allow the still run for a potentially a few minutes before collecting water to allow volatile chemicals to escape and just dump the residual water as it would still contain the heavy metals. Yes there is the potential of not taking in enough vitamins and minerals if you are drinking only distilled water but I personally don't know the extend of how dangerous it is so I will suggest do your own research/ personal decision. An idea for another project close to this is making a portable small sand filter.

Hi Nighthawk, Thank you for your always interesting videos. Nighthawk fill the coppet tubing with sand. Before folding it.

You can also mix a crushed CA/MG/ZN tablet in your pure water. A very small amount of your salt water is also good for the salt electrolytes.

I think this project along with a solar lens, would be a great kit for travelling in the sea!

@shanewilson3653

4 жыл бұрын

you can get survival desalinators for boats that float on the sea water and condensate clean water. good real brand ones produce about 1-2 litres a day Off brand Chinese ones can be hit and miss. A good indicator of production rate is its size and most should be more than 3 feet in diameter when inflated.

This video pops up in my recommendations every now and then. I’m glad to rewatch it every time. Really good video 👍

So I have made am exact version of this by following your video. It works perfectly. Thank you

You, sir, are a life saver! Thanks for sharing your knowledge basically for free! Cheers!

@diywatch5776

2 жыл бұрын

Good video

Having a community response playlist is just such an amazing idea! I remember when KZread had a video response feature where you could link your response to the original video, but that got sloppy real fast. But a curated playlist is an amazing alternative!

This is pure genius! Great compact design.

I live near the gulf and actually made a small ( though bigger than this) still for desalinization , in case of hurricane etc, emergencies when water may be an issue. I used an old beer keg for the container and a bit larger copper tubing. Another upside is, one can save the sea salt for food in a bad time for seasoning and preserving meats. I have tested it, but hope to never need to actually rely on it. Good tip on adding back some minerals, I wondered about demin water, now I know. Thanks.

@experienceofchris1108

Жыл бұрын

Sea salt that hasn’t been treated has harmful things in it and this process definitely doesn’t get rid of any contaminants or heavy metals, all it doesn’t is kill any bacteria that might be within the salt

I made one like yours with the 64 ounce wide mouth bottle, using a piece of cork cut to size for the lid, with the copper tube through it.

Great to see the courses you take on product/ industrial design are already paying off!

What an interesting, informative and helpful video tutorial this is, with excellent narration and video presentation. This inexpensive construction will certainly come in useful if one only has salt water at hand, and it earns its place in a kit, pack, vehicle or vessel because it works! In short, this is literally a potential life saving device! I look forward to constructing one and to see how it compares to my Katadyn Survivor 06-LL Desalinator, which I keep with a Katadyn Pocket Water Filter to give me potable water Irrespective of the supply. The narrator's voice is excellent in this tutorial, clear, easy to comprehend and with a natural flow. Subscribed.

What a fantastic project. Your device is brilliant. I feel that in bushcraft education, there isn't enough information about distillation and it really should be a basic everyone learns, beyond desalinization. Actually this device can produce purified water from almost any (non-radioactive) filtered water source, even a puddle or a natural bog. One that doesn't have a very strong smell or heavily colored water, as these indicate the possible presence of volatile compounds in the water which distilling (or filtering or boiling) wouldn't remove either. Before industrial dumping, such polluted water ponds, bogs and marshes were extremely rare. Unfortunately thanks to modern unscrupulous chemical dumps and pipelines leaks, it is not so uncommon anymore. So do be careful when selecting a water source, regardless of methods. Still many sources of water that can be distilled remain abundant. Boiling and filtering are usually sufficient, but there are some chemicals and particulates that regular filtering and boiling wont remove but distillation does. In these cases, you wouldn't add a small amount of the water concentrate into your distillate from your distillation bottle to remineralize. Instead a pinch of sea salt is sufficient, if you add a pinch of natural sugar too, it is even better. Or you could run your distillate through a clean sand and carbon filter (easily assembled with a plastic bottle or bag) and voila. You could also improvise a solar still using a large and sturdy enough clear plastic bag, a container to receive the condensation drips and a some sticks or other structural support to create a funnel or tube from the top of the bag, draping into the container while the plastic bag rest in a shallow open hole in the ground. Or other support or container that allows the sunlight to heat up the water in the bag, while it is held up. The bag should not be filled more than half its capacity and the top draped in to the container must be secured enough to hold its position but not in such a way as to preclude the flow of condensation. You can use this exact same plastic bag set up, even if you don't have water by filling the bottom half of the bag with greens, leaves, grass... Anything that contains enough moisture to create condensation. At any rate, thank you for such brilliant video. This is a project that I definitely plan on making. This information is incredibly valuable, thank you again.

Great video. Thank you. I wonder if you could distill into a second similar water bottle and draw a vacuum on it. Reducing the pressure lowers the boiling point. It is difficult to make hot soup on the top of Mt Everest.

So many KZread channels start out really well, then relatively quickly sell out their quality in exchange for money or popularity. Not so with yours. I have been subscribed to you for several years now, and every video you make is just as good as the one before it. Great job man! Thank you for your constant originality and consistency. Keep it up 👍👍👍

Planning a 2021 cycle trip in the Moroccan sahara, It's a good idea to take this with me as a backup. thanks for sharing.

Great video! Glad I ran into your channel through the video you made about waterproofing sheets and creating buttons! I like this video for the same reason: short, informative, covers all the steps clearly, and teaches me something that could save my life. Keep it up brother!

a cloth wet with seawater can also be tied on steam end to condense it and add salts as well

Great idea for emergencies, thank you for uploading it.

You should start a daily vlog channel. Your bird is so interactive with you. Great job raising it. So interesting.

Im very happy that you also spoke about the fackt that water can get to pure and how to solve it

Best voice! Works well probobly with any subject matter.compleatly nice,totally inoffensive,therefore, and easy to follow and comprehend. I would say gifted. Ataboy!

Bonus feature: you could froth up a nice latte with that steam nozzle 😂

@SnahLhug

4 жыл бұрын

This is udder nonsense! But in all seriousness, a countryside survival latte with freshly milked udder squirt is a nice touch to a good, long hike.

@XantherBlaze

4 жыл бұрын

@@SnahLhug No, a funny cow is udder nonsense...

lol cute conieur. glad you added that cooling bowl, watching the steam just poor out was driving me crazy, lol. i have built a few water distillation units in the past.

Wow! Great video: I will be on the lookout for parts to put one of these together. Thanks so much!

You could always transfer the salt water left over in the desalinator after distillation to a small can and finish boiling it out to collect the salt in that water. Sea salt is quite useful for many things... adding flavor to meats or other foods if you're camping and didn't take salt with you or to simply collect sea salt to take home with you. But if you are in an actual survival situation it can be even more valuable as a disinfectant, a preserving agent and an electrolyte. Great video... that was a beautiful, compact design for a desalinator.

@experienceofchris1108

Жыл бұрын

If you use straight up salt from the ocean there are some pretty harmful things in that salt and any contaminants and heavy metals can only be separated through pretty complicated procedure. The “sea salt” people buy in stores isn’t simply ocean water boiled down and for good reason.

@jamal69jackson77

Жыл бұрын

@@experienceofchris1108 true, but not all salt water poses those dangers and yes, it wouldn't be possible for the average person to know exactly which salt is safer for consumption than others, but I'm not talking about habitual use of sea salt, my comment is just for either sporadic use or emergency use. Even fish and shellfish contain a lot of those same heavy metals and other contaminants and yet most people make food of them without issue. That's why there's still a warning on some sea food about not over consuming it due to those same safety concerns. So you're right, there is a risk, but it can be mitigated.

Something like this using a Kelly Kettle would be brilliant! Also, the pack sized unit is great, but I would love to see a design for a home sized unit too for use in disaster prepping. I live in an earthquake prone desert city by the ocean, and if the big one ever wrecked the aqueduct infrastructure we all rely upon to bring us water, being able to harvest and process seawater could be a true lifesaver.

@DKFX1

2 жыл бұрын

Just tried it with my own Kelly kettle, but the vapors didn't seem to properly desalinate. I'm thinking the boil inside the kettle was too violent and splashed salty water into the tubing and got stuck between air bubbles which transported it into my pure water vessel. Will attempt again to see if I can get it right.

@gorisenke

2 жыл бұрын

Ngl sounds like SoCal. 🤣

@DKFX1

2 жыл бұрын

Got it working using the kelly.

Very efficient design. If I lived or traveled anywhere near salt water i'd certainly be putting one of these together.

YOUR PROJECT WAS GREAT. YOU DID AN EXCELLENT JOB SOLDERING WHICH IS VERY HARD TO DO.

Excellent design and advice on the soldering!

This is a great application of science. This could be used to remove lead from water as well. Although it is a bit cost prohibitive in a city.

Love it dude,!!! You go into details without going into boring details,,I'm into survivor stuff, this is good material.

@1973Saved

3 жыл бұрын

Just remember, there is not a thing wrong with drinking 'straight' distilled water, I've been drinking it exclusively for about 30 years, I am very healthy & my Primary Care Physician says that my bones are "well mineralized". If you don't believe me I suggest you do some research online & find out.

Lol!!! That birdie was about to put your eye out with that pen! It must be one of his favorite toys because he looked like he was having a lot of fun with it!

Great design . Easy way to thwart all the little nasty things in sweet water as well .

Ill remember this, The day might never come that I need it but now if it does come I got somthing ill remember,

This is a very good improvised distillation rig. The product is pure water from whatever quality water is being processed. It could be used on contaminated fresh water or (ewww!) urine. The product would still be wholesome distilled water. I wouldn't add any of the contaminants back in except with sea water though.

@reichrunner1

4 жыл бұрын

You still have to be careful with contaminated water though, as any volatile organic compounds would evaporate right along with the water and get condensed back into your "clean" water. You could fix this with multiple steps of recondencing at different temperatures, but this isn't really going to be practical for you to carry on a hike.

Your little buddy is ADORABLE!!!!

Such a intresting , very useful & important things you saw. We are very thankful .god bless you.

This is an AMAZING idea and I will be trying this out myself when I get the chance! Keep the good ideas rolling!

I love the idea!!! I think for mine I will use stainless tubing and swedgelock fittings. Then there is no need for the soldering. I can get a stainless cap for the top fitting when not using the still to eliminate the plug. The stainless will be more rugged and take more abuse from me. It takes a little practice to bend stainless tubing correctly and you need the right tool. Side note, I would have used silver solder and when soldering you heat the materials and apply the solder to the surface of the heated materials, you shouldn't torch the solder directly. Just something you learn when working on HVAC.

@roadchewerpe5759

4 жыл бұрын

So, in this case, heat the lid, and not the solder and flux?

@tnwhitley

4 жыл бұрын

roadchewer PE correct, the lid and the tubing, when they’re hot enough the solder melts and flows to them, just don’t over heat them.

@drjheyer

4 жыл бұрын

make a video of you making yours and let us know

@colemarie9262

4 жыл бұрын

Came to comment just that, if you carefully heat the materials it will suck the solder right in neatly. (Neater on a pipe type shape though, so heating one end really pulls the solder in)

@owenheffernan9355

4 жыл бұрын

This is just putting water.throgh a miny moonshine still

Well Sir, ur a great teacher. Lots of details.

Hand towel, rivet holes amd tied in place with leather thong. You can wet towel to increase cooling by evaporation. When done towel can be used as a towel.

That was informative thanks. One would think if working at sea this may be handy to have just in case!

@catprog

4 жыл бұрын

How do you get fuel?

@davemwangi05

4 жыл бұрын

don't talk of handy at sea, watch a documentary called, "Lost at sea for 72 days, by Wonder." You will shed tears.

@derekdavis3684

4 жыл бұрын

right?

i really like this design! just so you know i drink a gallon of distilled water a day! an been drinking it for almost 7 years!

@joeblowjohnny2297

4 жыл бұрын

Distilled water lack the minerals your body needs unless you know what you doing .... it can killed you !

@dimasirvan8516

4 жыл бұрын

@@joeblowjohnny2297 Life can kill us for mostly from everything. Earth is dangerous, if he can live well for 7 straight years drinking a distilled water, perhaps you can be dead by tomorrow just because your wreckless when crossing a street and hit by a truck.

@Nae_Ayy

4 жыл бұрын

@@joeblowjohnny2297 it can't kill you if you eat food, because food has all the minerals you need.

I'm tempted to make this from two bottles. Not only can one use the bottle on its own, but when submerged in a container for condensation, it offers larger surface area.

Instead of damaging the bottle from the fire, you could use a double boiler method. This could solve multiple issues for this project, as you could build up bricks/ rocks for the fire, avoid overheating and avoid a damaged valuable piece of equipment. Hope it helps.

@IluvinortheIneffable

9 ай бұрын

Smart. Ill keep that in mind.

@austinhunt8050

8 ай бұрын

As long as there is water in the bottle you will not damage the bottle. And since salt water has a higher boiling point than fresh water the water will need to get hotter and hotter to boil and produce enough pressure to get through the condenser. This is not an issue with open flame but double boiler will pretty much not work unless you use something with a high bp such as oil

@ncuser4642

7 ай бұрын

How long does it take to build heat in an open flame with rocks or bricks versus a metal can as I. Video? When you are dehydrated in an emergency, time matters!