Dang. It’s like he does this every weekend. Best kingpin rebuild tutorial on YT.

@Offroadfarm1

3 жыл бұрын

Thanks for watching

@saltyfabs4502

3 жыл бұрын

Glad I wasn't the only one thinking this! Amazing work!

Great videos. Simple and to the point. Thanks.

@Offroadfarm1

5 ай бұрын

Glad you like them!

@Chevyholicsanonymous

5 ай бұрын

Making my rebuild go super smooth f3lla thanks again! Im having a bit of a hard time tracking down a part # on those outter axle seals to keep the shmoo out of my axle tubes. You wouldnt happen to have them bu chance eh?

@Offroadfarm1

5 ай бұрын

Outer axle seals: www.offroaddesign.com/d60-outer-axle-seal.html Try that link

@Chevyholicsanonymous

5 ай бұрын

What a beauty. Thanks !!

It’s a great video for full rebuild I came here just for the spindle. I’d think having multiple videos, of key components would give you the most content and specific as well.

@Offroadfarm1

Жыл бұрын

Thanks for watching and for the comment

@Joshua-yn1zx

4 ай бұрын

I'd like to see race and bearings inner and outer.

Awesome video!!! It’s going to come in super handy when I rebuild my Chevy d60 soon!!

@Offroadfarm1

5 ай бұрын

Thanks for watching

Your video has been a life saver for my ford Dana 60. Interestingly enough my axle goes: brake caliper, dust shield, then spindle

@Offroadfarm1

3 жыл бұрын

Glad you found the video helpful. Thanks for watching!

Great Video!! Thumbs up!! FIY ,, I was told many years ago ,,NEVER put any Grease at ALL , None ,, where the Bearing Races Sit on the Spindle. Clean and Dry in that Area on the spindle. Reason being, We dont want the "INNER" Bearing Race to Ever Spin on the Spindle. Thanks for showing how the seals are orientated. Great build video!!!

@Offroadfarm1

2 жыл бұрын

Thanks for watching!

Good to see you getting back on this project.

@Offroadfarm1

4 жыл бұрын

Me too! Thanks for watching

Excellent video. Thanks for putting it up, it was awesome to have while I was working on my axle.

@Offroadfarm1

2 жыл бұрын

Glad you liked the video. Thanks for watching!

Excellent job!

@Offroadfarm1

3 жыл бұрын

Thanks for watching

Great Video. Thanks for doing it.

@Offroadfarm1

3 жыл бұрын

Thanks for watching

Those Dana 60's are the little brother to the Dana Super 60 that are found on the 2017 and up super duty trucks which offer a 10" ring gear 3.5" axle tubes with 1/2" wall, 35 spline inner and outer axle shafts and 1550 steering u-joints this is the axle I used on my solid axle swap duramax dually

Great video, not much out there on the full tare down of he Dana 60. This being a chevy, pretty much the same as my 79 F350 Dana 60, except the outer locking mechanism. As for time, there are lots of videos way longer than 30 minutes. So watching this kind of content is worth all in one sitting. Can you please give a good source for the parts you installed? Thanks!

@Offroadfarm1

4 жыл бұрын

Glad you liked the video. Which parts are you referring to? Pretty much everything came from offroad design. The spartan locker, new pinion and carrier bearings, new high steer arm for the passenger knuckle, all king pin parts (bottom kingpin seals, bottom kingpin caps, top kingpin seals, spring retainer, spring, kingpin bushings), outer axle seals, spindle bearings, stub shaft seals, and stub shaft dust cover. Check them out, they have parts for GM, Ford, and Dodge Dana 60's. I've always had great customer service from them and if you have any questions about your 60, they can probably answer it. Thanks for watching.

@denniskwasnycia1950

4 жыл бұрын

@@Offroadfarm1 All seals and bearings, pretty much everything from the "U" joints out. Thanks for your response and I will check them out!

@Offroadfarm1

4 жыл бұрын

www.offroaddesign.com/axles/dana-60-front-axle.html

@smallblockfuelie

4 жыл бұрын

Dennis Kwasnycia I agree. If it’s all on the same topic, or Dana 60 in this case, having all the content in one video is a good thing.

30mins would be fine with me

I like the way you broke up the videos. That way while I'm in the midst of rebuilding rebuilding my axle I can kind of remember which part was in which section. Thank you very much by the way for making these tutorials. I would have had to pay someone to do it for me otherwise, something I can't stand or afford. Have you made a crossover steering for the Dana 60 tutorial? Thanks

@Offroadfarm1

2 жыл бұрын

Thanks for watching and I'm glad you found the video helpful. I am making a steering video. Waiting on a few last parts right now.

Awesome video, I'm getting ready to do mine. Dana 60 out of a 89 F-350 going in my 87 F-250.

@Offroadfarm1

3 жыл бұрын

Good luck on your project and thanks for watching!

What was your final torque on the outter lock ring? I saw you hit 50 and said you like a little more. What so you recommend? I appreciate your videos I am currently doing this on a cucv

Hey awesome video!! Thumbs up. Wondering what brand of torque wrench you are using

@dstock138

2 жыл бұрын

Nevermind I found it in the description

@Offroadfarm1

2 жыл бұрын

Thanks for watching

Great video. Whats the part number or link for the spindle nut socket?

@Offroadfarm1

2 жыл бұрын

Glad you liked the video. If your spindle nut has 4 notches in it then this socket should work amzn.to/3qvSb7A Thanks for watching!

Have a dually kingpin coming here in a few minutes. Gonna convert it to six lug. I’m a yota guy, gotta learn this Dana stuff. Awesome Vids!

@Offroadfarm1

3 жыл бұрын

Good luck on your project and thanks for watching

This fella sounds just like Danny McBride 😂

@Offroadfarm1

Жыл бұрын

Thanks for watching!!

@scumdog88

Жыл бұрын

@@Offroadfarm1 great videos I needed a refresher been a couple years. Thank you

After you install the caliper dust shield you put the little ring on there. I don’t have one of those. Do I need it? I ordered the solid ind 8x6.5 kit and it doesn’t come with it. The axle is on a rock buggy.

@Offroadfarm1

2 жыл бұрын

You should be fine without it. Just make sure you have enough threads on the studs in the knuckle to tighten down (they should be, but check) Thanks for watching

How many hours of labor do you think you have in to the rebuilding process? Not ordering parts and all that but, once you have all the parts on hand. I’m looking at doing a rebuild project and trying to get a general idea. Thanks 🙏🏽 🤙🏽

@Offroadfarm1

Жыл бұрын

It's hard to say but if you have everything you need and are mechanically inclined then you should be able to rebuild one in 8 to 12 hours. If your going to be re-gearing then probably double that. Thanks for watching and good luck on your project.

just seems so loose backing off 90 degrees