DIY 2013 2014 2015 2016 2017 Honda Accord Replacing Rear Brake Pads
Автокөліктер мен көлік құралдары
Watch how to replace rear brake pads on a 2013 2014 2015 2016 2017 Honda Accord. #honda #hondaaccord
Parts & Tools Used:
Rear Brake Pads - amzn.to/44ctbFC
Disc Brake Caliper Compressor Wind Back Tool - amzn.to/44yoaqE
12mm Socket - amzn.to/4bn25i8
3/8 Socket Wrench - amzn.to/4bONMTn
Brake Part Cleaner - amzn.to/4dF17iC
Brake Grease - amzn.to/4bN376F
Adjustable Wrench - amzn.to/3WPlWSK
Jack - amzn.to/3QUtgZr
Jack Stands - amzn.to/3wLl5rt
Пікірлер: 48
The tool to rotate the caliper back was new to me. Awesome, Thank you. i spent an hour trying to use c clamp, cussing and wondering what i was missing.
@MobileCarMechanic
7 ай бұрын
Glad it helped
@carlreich
3 ай бұрын
Dude! Me too. I was so mad it wouldn’t compress😂
@nickolasrosenthal7757
2 ай бұрын
Were do u get one of them
@robm321
Ай бұрын
@@nickolasrosenthal7757 Amazon for cheap
One thing that is missed here is that the cross pattern on the caliper has to match the pin on the rear plate of the brake pad. If it does not line up it will create excess pressure and wear the pad in no time. I like you must have been lucky a half a dozen times before I hit this issue
@MobileCarMechanic
Жыл бұрын
I have not been that lucky but I went back and ensured the cross pattern on the caliper matched the pin on the plate. Thank you for the feedback.
Another great vid 👍 I did 2 vids on this with pads and rotors for both front and rears since I was getting a clown horn noise when braking
@MobileCarMechanic
10 ай бұрын
Greatly appreciated! Cheers!
Before mounting the wheel back up, pump up the brake pedal. then use the parking brake to keep the wheel from spinning when you tighten up the lug nuts.
@MobileCarMechanic
8 ай бұрын
Very good tip! Cheers!
@thardyryll
8 ай бұрын
Or merely pre-torque the lug nuts with the impact wrench and lower the vehicle to the ground for final tightening...
Great video
@MobileCarMechanic
10 ай бұрын
Thanks!
You installed your caliper pins in the incorrect order. The pin with the rubber bushing and the line machined around the flats goes on the top. I removed both pins from my caliper bracket yesterday and got them mixed up. I had to go find an exploded diagram online to see where they went. Supposedly the rubber bushing has something to do with mitigating vibration when braking...
@MobileCarMechanic
9 ай бұрын
Thanks for letting me know. Got distracted and forgot which order. I know it helps with evening out the travel to wear pads down evenly. Gonna swap them in the correct order. Cheers!
One thing I would like to add, it is best practice to line the channel on piston face with nipple on break pad.
@MobileCarMechanic
5 ай бұрын
Thank you for the suggestion.
Thanks!
@MobileCarMechanic
3 ай бұрын
Glad our video helped. Greatly appreciate the donation. Cheers!
thanks
@MobileCarMechanic
Ай бұрын
You're welcome!
do you have videos on how to do brake flush on honda 2017
@MobileCarMechanic
Ай бұрын
I do not at the moment. Thank you for the suggestion.
hello and hi what is the torque spec for honda hrv 2020? on the front and rear brake thanks all the bolts
@MobileCarMechanic
Жыл бұрын
50 N-m (5.1 kgf-m, 37 lbf·ft) Front Caliper 108 N-m (11.0 kgf-m,80 lbf·ft) Front Caliper Bracket 35 N-m (3.6 kgf-m, 26 lbf-ft) Rear Caliper 108 N-m (11.0 kgf-m, 80 lbf-ft) Rear Caliper Bracket
@user-wm4bo4nj8l
11 ай бұрын
@@MobileCarMechanic hello also what is the torque spec for spark plugs on honda hrv 2020 with a grease and the gaping on spark plugs should i change it or leave it when i buy the spark plugs?
Pretty good job. But you didn’t torque bolts on caliper 37 ft lbs. didn’t lube hardware for disc brakes. Didn’t use silicone on slider pins ( not brake grease ). Minor things but makes a difference. Thanks
@MobileCarMechanic
7 ай бұрын
Thanks for the info
So no need to open up brake reservoir when pushing caliper piston back?
@MobileCarMechanic
3 ай бұрын
If your just doing 2 axles then you are good to go, if you did all 4 wheels then it may leak.
@SoCalGeo
3 ай бұрын
@@MobileCarMechanic ok, good to know. Thanks for the reply.
You must be a renter. Spraying and lubricating with nothing underneath 😂
@MobileCarMechanic
3 ай бұрын
Haha it’s my friends driveway.
@carlreich
3 ай бұрын
OMG, is he still your friend? Brake cleaner eats everything and that includes asphalt
@carlreich
3 ай бұрын
I appreciate the video, had no idea that the rear piston was a screw type. Tool ordered to be delivered tomorrow
@mikegrizwold2522
Ай бұрын
😄
Other than the switched caliper pins, my only other issue is the rock chock!!! 🤣
@MobileCarMechanic
Ай бұрын
Thank You for your feedback, Needed to include a little bit of nature in our video haha
@mikem1129
Ай бұрын
@@MobileCarMechanic 😂
Should try a better angle , couldnt really see much and couldnt see how far out the break pads supposed to go
@MobileCarMechanic
8 ай бұрын
Thank you for the feedback! Cheers!
Careful not to overtorque those guide pins, they're only about 15-19lb-ft
@MobileCarMechanic
10 ай бұрын
Thank you for the advice!
You put the wrong slider pin, in the top, and vise, versa. 🙄 🛠
@MobileCarMechanic
2 ай бұрын
Thanks for catching that.