I have had to do this video in 2 parts , first is disassembly, then in part 2 the repair of a dead unit.
Жүктеу.....
Пікірлер: 10
@truthreigns76 ай бұрын
Glad to have you on here again.
@michaeldranfield7140
6 ай бұрын
Not been any ware, just had Christmas and new year off work so no videos but getting back into the swing of it now .
@truthreigns7
6 ай бұрын
@@michaeldranfield7140 Good, i hope you had a wonderful Christmas and New Year.
@wisher21uk6 ай бұрын
Nice bit of info thank you 😊
@michaeldranfield7140
6 ай бұрын
Made this video to remind me in the future !
@Barbarapape6 ай бұрын
Simple when you know how! I once did the same with a VCR lid and cut my fingers to the bone. Now i never run my fingers on the edge of a lid.
@michaeldranfield7140
6 ай бұрын
this is now the second one of these I have done but as its a while back I couldn't remember how it was done so I made this video to remind me in the future, the lid is so tight and doesn't seem to move in any direction until you realise it slides , I don't have a clue how the bottom comes off though ! The later videos where the worst as they make the metal thinner to cut costs .
@Barbarapape
6 ай бұрын
Thinner metal makes the edges razor sharp as i found out the hard and painful way! Even if you have the service manual they don't always provide any instructions as to how it all comes apart. Everything these days is designed to cut costs and to be thrown away when it fails@@michaeldranfield7140
@Disillusioned_one6 ай бұрын
Last one was a short cct diode, middle of 3 diodes. kzread.info/dash/bejne/loWftdyxe5mvkps.htmlsi=0Dc9AoCACMiM7Cv4
@michaeldranfield7140
6 ай бұрын
Many thanks for that , I didn't know how to put the two videos together so I had to do it in two parts .
Пікірлер: 10
Glad to have you on here again.
@michaeldranfield7140
6 ай бұрын
Not been any ware, just had Christmas and new year off work so no videos but getting back into the swing of it now .
@truthreigns7
6 ай бұрын
@@michaeldranfield7140 Good, i hope you had a wonderful Christmas and New Year.
Nice bit of info thank you 😊
@michaeldranfield7140
6 ай бұрын
Made this video to remind me in the future !
Simple when you know how! I once did the same with a VCR lid and cut my fingers to the bone. Now i never run my fingers on the edge of a lid.
@michaeldranfield7140
6 ай бұрын
this is now the second one of these I have done but as its a while back I couldn't remember how it was done so I made this video to remind me in the future, the lid is so tight and doesn't seem to move in any direction until you realise it slides , I don't have a clue how the bottom comes off though ! The later videos where the worst as they make the metal thinner to cut costs .
@Barbarapape
6 ай бұрын
Thinner metal makes the edges razor sharp as i found out the hard and painful way! Even if you have the service manual they don't always provide any instructions as to how it all comes apart. Everything these days is designed to cut costs and to be thrown away when it fails@@michaeldranfield7140
Last one was a short cct diode, middle of 3 diodes. kzread.info/dash/bejne/loWftdyxe5mvkps.htmlsi=0Dc9AoCACMiM7Cv4
@michaeldranfield7140
6 ай бұрын
Many thanks for that , I didn't know how to put the two videos together so I had to do it in two parts .