Thanks to a viewers comments. I realized I forgot to install the stock bottom bolt spacer. I went ahead and put it in and wasn't too hard to do it without removing the top bolt mount.

@leathaelsdon9438

2 жыл бұрын

Great video!! Can I ask where you purchase them from? Also, have you tested them by laying the bike gently on a lawn or pads? I'm trying to figure out if they will keep the handle bars from denting the gas tank in a slow drop. Not that I have dropped my bike;)

@MacrossGarage

2 жыл бұрын

@@leathaelsdon9438 I got them from Webike in japan. No I have not test laying my bike down. I get that question alot. Maybe I should make a video of it. Thank you.

Thank you so much for this video. I'm always a little nervous about working on stuff like this, especially with my bike only being a couple months old, but I just followed this video step by step and it was way easier than I expected. Got it installed no problem.

@MacrossGarage

2 жыл бұрын

You are welcome, glad it worked out. I am alway nervous when I work on my vehicles. I always play it safe.

I just finished installing the crash bar this afternoon and it turned out to be pretty straightforward thanks to this video. Thank you so much for your generosity by filming and sharing.

@MacrossGarage

Жыл бұрын

You’re welcome glad it worked out.

Thank you. I used your video as step by step instructions. Couldn’t have done it without your help!

@MacrossGarage

2 жыл бұрын

Glad it helped. Its the reason I make the videos.

Can confirm this also works on the 2023 crash bars I got as well

@MacrossGarage

3 ай бұрын

Thanks for the info.

Thanks for putting this video together. Because of this and Google Translate I was able to get mine installed tonight. I'd have probably avoided these without the video, so they should be thanking you for the extra sales. Great work!

@MacrossGarage

2 жыл бұрын

Good to hear. It's the reason I make videos. There other videos out there that helped me so just paying it forward.

Just ordered mine. Great video! This will certainly help with the install. Thanks 👍🤙

@MacrossGarage

2 жыл бұрын

It’s the reason I do it, to help others. Good luck and let me know if you have questions.

Great video! Been waiting for this for weeks. Thanks a lot, man. Subscribed

@MacrossGarage

3 жыл бұрын

Thank you so much, glad you liked it.

I like the fact they can be used like forward pegs. i'm going to order those. Thanks for the video.

@MacrossGarage

2 жыл бұрын

I don't travel far enough to need foward pegs but I find that I am using them a lot more.

Thanks so much for your video! The bars literally came without instructions, so i'm glad I found you video. Very simple and well made vidoe. Straight to the point. No annoying music.

@MacrossGarage

Ай бұрын

Always good to hear it worked out.

Thanks for this video. I just finished installing my crashbar!

@MacrossGarage

Жыл бұрын

Nice, glad it helped. Ride safe out there.

Great job, on both the installation and the video! Thanks for taking the time to put it all together.

@MacrossGarage

10 ай бұрын

Thank you for the compliments, it was my pleasure making the videos.

After watching this video I also ordered. Aset of ceashbara for my Honda rebel. They seem to be sturdy. But installing them took all my morning, but I'm happy with how they look.

@MacrossGarage

2 жыл бұрын

Glad they worked out.

Just installed my engine guard (Ebay replicas) and thank you so much, your video was very helpfull, you made my day !!!

@MacrossGarage

Жыл бұрын

You’re welcome glad it helped.

Nicely done, thanks for the lesson . Doing mine tomorrow

@MacrossGarage

Жыл бұрын

No problem, glad to help.

Thanks for the video! I just ordered mine and can't wait

@MacrossGarage

3 жыл бұрын

Let me know if you need help with the install.

@emilsantos1602

3 жыл бұрын

@@MacrossGarage I’ll let you know! Thanks. The your video is fairly thorough.

@rosalieboring7077

3 жыл бұрын

Who did you order them from??? Daytona website is way to complicated

@emilsantos1602

3 жыл бұрын

@@rosalieboring7077 The link is in the description. I got it from there. =]

Great "how to", awesome content. Thank you!

@MacrossGarage

2 жыл бұрын

Thanks for the kind words.

Thank you for making this video! It's great man!

@MacrossGarage

3 жыл бұрын

Thank you, glad you like it. Makes time and effort worth it.

@r6bendlova

3 жыл бұрын

@@MacrossGarage love how you show every step of the process and the results! Great Great Great camera angle! Please share it on the Facebook page if you are a member, many people would be grateful!

@MacrossGarage

3 жыл бұрын

@@r6bendlova I dont have a FB page but may consider one, thanks.

These work, saved my gas tank from a slow turn. I was working on figure 8, too slow.

@MacrossGarage

2 жыл бұрын

Glad you and bike are ok. Was the guard bent or anything?

Thanks for sharing your knowledge!

@MacrossGarage

2 ай бұрын

You’re welcome

Looks fabulous

@MacrossGarage

2 жыл бұрын

Thanks.

Great video! Thanks for sharing.

@MacrossGarage

3 жыл бұрын

No Problem, glad you liked it.

I used your video and it worked great thanks.

@MacrossGarage

2 ай бұрын

Glad it helped

Awesome rebel. I really want one.

@MacrossGarage

2 жыл бұрын

You won’t regret it.

Thanks for this!

@MacrossGarage

2 жыл бұрын

You are welcome

Thanks for useful video. I just ordered mine. But noticed you used a front wheel chock and wondering if this is needed for the install or if one can support the engine with a jack without it as I will need to buy one if that is the case.

@MacrossGarage

2 жыл бұрын

I suppose you don't need one and just rely on the kick stand. You just have to work on it with an angle and make sure you support the engine.

Excellent video. I followed your process exactly, and it worked out perfectly. The Daytona engine guards shipped from Japan, and appear to be a very high quality product. Quality materials craftsmanship and finish. ONE QUESTION: The hardware package included a short bolt (12mm), I presume this bolt is to be used to attach the horn to the left engine guard? The original bolt on the bike works fine, some I'm wondering why the extra bolt was included.

@MacrossGarage

2 жыл бұрын

I don't remember the bolt setup for the horn. Not sure if it came with it or not.

@MacrossGarage

2 жыл бұрын

After looking at the instructions, it is probably for the horn.

@wave6413

2 жыл бұрын

Its for the.... horn but the original is better

Just got mine installed, thanks for the help. Did you put back the spacer for the bottom bolt?

@MacrossGarage

2 жыл бұрын

I did not put a spacer on the lower bolt.

@MacrossGarage

2 жыл бұрын

FYI, You should put that spacer on the bottom bolt. After one more comment talking to another viewer I realized I was mistaken.

Hey great video! very easy step to step. I was wondering if you have the PDF instructions? I just needed to see what the long bolt and nut size and length is as mine didn't come with it.

@MacrossGarage

10 ай бұрын

I forget where I put the instruction. I’ll look and let you know. If you contact webike they might email you the manual.

Do the heat shields need to come off? Are they in the way of the install? From the video it's hard to tell.. it doesn't look like they're in the way that much... great job on the video and thank you for this...

@MacrossGarage

3 жыл бұрын

Thank you. The left cover give you more room to hang the horn while it is off. The right cover gives you more room on the lower bolt and you risk scratching the cover. You can probably do it without removing the covers.

@knightsofni1999

Жыл бұрын

Is this is an install on a DCT model? The cover on the right side is different on my manual model. Manual cover seems smaller.

Thanks for the video. It was very helpful. I have a suggestion for your next video though. I feel it would help even more if you were actually talking and explaining what you were doing in each step, instead of just silence. There were times during the video when I wasn’t sure which side of the bike you were working on. Also at the end it would have been helpful to show the bars fully installed. But very helpful nevertheless. Much appreciated!

@MacrossGarage

Жыл бұрын

Hi, Thank you for the kind words and suggestions. That was one of my early videos and I learn from each one. I do recognize some of the mistakes I make. As far as me talking, I've been ask a few times before :) There are a few reasons I don't talk. One is I am not gifted in talking and if I talk, it would require a lot more editing that I would want to do. Also since I dont talk, I tend to put more focus on the video which I think makes better quality videos. Lastly I was inspired to make videos from other DIY videos that hand no music and no talking and honestly I used them to fall asleep as well :)

Great video. Where did you buy the motorcycle stand?

@MacrossGarage

2 жыл бұрын

Cycle Gear.

Thank you for the video. No loctite on those motor mount threads?

@MacrossGarage

3 жыл бұрын

There wasn't any from what I can see. I didn't put any when I put them back. I will be checking the bolts from each ride.

I just ordered mine

@MacrossGarage

2 жыл бұрын

Nice.

Did you find that the guards were wide enough to provide enough protection for the tank and side of the motorcycle? Or do you wish they were a little larger?

@MacrossGarage

2 жыл бұрын

From what I can see the the engine is well covered. The engine doesn't really stick out that much.

はじめまして。　私もこのエンジンガード付けてました。でも、すぐ外しました。なぜなら、バンク角が浅くなるからです。傾けずに乗るライダーならいいでしょうが、一般的な走行でもすぐ接地します。　おすすめのエンジンガードは、プロスマンですね。強度とバンク角共に優れてます。

@MacrossGarage

4 ай бұрын

Interesting, I haven’t scraped mine and I lean me pretty good.

So are they comfortable for your legs? What about adding some black grip tape to where your foot goes?

@MacrossGarage

9 ай бұрын

They are comfortable for the legs, although I don’t use them much for that. Grip tape would help.

I have a question, my wife is thinking about adding a set of forward controls (CMX1100 DCT Rebel 2022/23 - Kit Original Controls Repositioning (S-0832) - Footrest Footpegs - Hardware Fasteners Included - De Pretto Moto Accessories (DPM Race) - 100% Made in Italy) to her 1100T. Will the Daytona guards work with this set of forward controls?

@MacrossGarage

Жыл бұрын

After looking at the photos, i am going to have to guess it wouldn't work. The left side might be ok but the brake pedal might hit the guard bar and even if they fit, the guard bar will probably get in the way of your feet. Those are nice looking forward controls though, thanks for sharing.

Hi Macross. One question. Can't reach the road in a bend? And one more question, where do you raise your motorcycle? Thanks for the answer.

@MacrossGarage

2 жыл бұрын

Hey Zoltan not sure what you asking with your first question. I am assuming you are asking if it scrapes when I turn? I used a front wheel stand then raised the engine with a jack.

@zoltannyari9571

2 жыл бұрын

So i try to asking. 🤣Does the crash bar not reach the road when cornering?

@MacrossGarage

2 жыл бұрын

@@zoltannyari9571 No, i've never once scraped them.

I just received crash bars through Amazon. The have a name of Baione on them and came with absolutely no instruction. Box says "made in China", my bad but they do look just like the one you installed with spacers and all. I'm still a bit nervous but plan to attempt this install. I would have had no ideal where to start. Glad I found your video

@MacrossGarage

Жыл бұрын

I just looked them up and they do look the same. Good luck hopefully the quality is up to par. Let me know if you have questions.

@bartowens55

Жыл бұрын

Got it all done yesterday in my 28degree barn. Would not have attempted it without your video. The bars that came from China ha holes that were about 1/16" off. Used a Dremel to slightly elongate.

@MacrossGarage

Жыл бұрын

@@bartowens55 Glad you got it done. Post a review for others to benefit on Amazon. Thank you.

What about lean angle of the bike? Doest it reduces it?

@MacrossGarage

2 ай бұрын

I’ve tried to lean them to scrape but have t been able too.

Looks like the highway bar reduces the lean angle. Any experience or thoughts?

@MacrossGarage

2 жыл бұрын

I thought about it when I first installed it. I try to lean it as much as I would normally do and so far I haven’t scraped it.

@tomabfall3955

2 жыл бұрын

@@MacrossGarage super. Thanks for the response

@MacrossGarage

2 жыл бұрын

@@tomabfall3955 You're Welcome

I was thinking of fettering these but I’m afraid it limits the leaning angle?

@MacrossGarage

Жыл бұрын

I don’t think it limits it. I’ve seen a video awhile back that leans the bike all the way down and the pegs hit first.

Before I go look at my Bike to install, Asking...Any reason Can't install One Frame bolt at a time - L-R Lower first- snug NOT tight/remove upper then Inches away- Push each side upper into place then place and tighten All both lower and upper (or Visa-Versa-Upper first?) Without having to support Engine weight from the Bottom(jack/Blocks etc...)? Or design allows NO Back-Forth swivel play for that?

@MacrossGarage

3 ай бұрын

I suppose you can. Hopefully the exhaust doesn’t get in way. Some have also said you don’t need to support the engine since there are other mounts still holding it. I just wanted to be really safe and didn’t want to deal with an engine moving on me.

@user-pt1vd1cd3v

3 ай бұрын

Thank You Sir...Simply trying keep things as less complicated as need to be and I ask YOU because done Hands On and many times Easier route not visible until....After already done=hind sight! thinking, Damn, I could've done easier this way, lol🤣@@MacrossGarage

@MacrossGarage

3 ай бұрын

It’s always easier the second time 😅

I just wonder, is jacking the bike up like this needed? I ask because I don’t have a jack and want to install these.

@MacrossGarage

Жыл бұрын

The jack is used to support the engine so it doesn't move out of alignment when the engine bolt mounts are released. If the engine moves it will be hard to put the bolts back on. You can probably do it without a jack and hope it doesn't move, but there is that risk.

I am trying to figure out which bars offer the most coverage. Thinking about the t-Rex bars.

@MacrossGarage

Жыл бұрын

T Rex probably covers more than the Daytona even though they seem to sit high.

@8flux

10 күн бұрын

T-Rex for sure, but aesthetically they’re ugly (imo).

Can u rest ur feet in the crash bars for long highway cruises?

@MacrossGarage

Жыл бұрын

Yes you can. I tried to show my feet at the end of the video. I am 5’8”

Is screw lock glue not needed when installing or putting the bolts back on?

@MacrossGarage

2 жыл бұрын

I don't remember the factory bolts having any. It probably doesn't hurt to put some on.

@Voltomess

2 жыл бұрын

for stuff like that you always want ot use loctite just in case......

The hardest part is trying to line up the top bolt to get it back on the left side

@MacrossGarage

2 жыл бұрын

Yea that does get difficult. For me was placing the spacer for the same mount.

I was trying but i had nothing to support engine up

@MacrossGarage

Ай бұрын

I think some people installed it without using a support. I like to play it safe and support the engine.

very cool. give us your opinion in everyday, please. practical, you can put tour feet in motion. curves, etc.

@MacrossGarage

3 жыл бұрын

I will once i use it more. At the end of the video I show myself riding with my foot on them.

DZIĘKI !! Polska pozdrawia !

@MacrossGarage

6 ай бұрын

You’re welcome

Do u need the jack to replace the crash bar, or can u do it without rising the bike?

@MacrossGarage

Жыл бұрын

You can i suppose. As long as you dont mind working on it at an angle.

@MacrossGarage

Жыл бұрын

Oh and also, remember part of the engine is not supported when you removed the bolts.

Are you saying that you need to use the jack/lift to support the engine from underneath when removing engine mount bolts?

@MacrossGarage

2 жыл бұрын

Yes, to avoid the engine moving or sagging.

@lisabradley6466

2 жыл бұрын

@@MacrossGarage Thank you! And just one more question....does the engine bolt not need a specific torque when tightening?

@MacrossGarage

2 жыл бұрын

@@lisabradley6466 I didn't torque mine but after some research it probably around 45 ft lb. Ask as many questions as you'd like.

@lisabradley6466

2 жыл бұрын

@@MacrossGarage Thank you so very much!

Great video. This is probably a dumb question, but I have never worked on my motorcycle. I'm a newbie. I have a jack to hold the engine, but do I need a stand to hold the bike upright or can I use the kickstand? Thank you.

@MacrossGarage

2 жыл бұрын

The side stand should be ok but the tilt might make it awkward. I've never tried this with the side stand though. Hope that helps.

@rustyscrib6071

2 жыл бұрын

@@MacrossGarage Yes, it does help thank you. One more question, I'm assuming you're using a 3/8 torque, but I cannot find the amount of torque you're supposed to tighten the engine bolts. I don't want to overtighten or undertighten on my engine.

@MacrossGarage

2 жыл бұрын

@@rustyscrib6071 A previous comment asked and I think they found after searching its around 45-55 NM or 35-45 ft-lb. Ask as many questions you like hopefully I have the answer.

@rustyscrib6071

2 жыл бұрын

@@MacrossGarage thanks for the info. My neighbor has been riding for over a decade is going to help me with it. I went ahead and bought a service stand for the back wheel.

@MacrossGarage

2 жыл бұрын

@@rustyscrib6071 The stand will be worth it in the long run.

I will be taking the bike to the shop next Monday so they can install the crash bar. I want to make sure that if they remove pieces I get it back. Can you provide me with the list of parts that I need to get back?

@MacrossGarage

2 жыл бұрын

I'll look tomorrow to see what I had left over.

@hbarrero05

2 жыл бұрын

@@MacrossGarage thank you!

@MacrossGarage

2 жыл бұрын

@@hbarrero05 It looks like I have one long mounting bolt which is the top one if I remember correctly and two spacers.

Will these actually do anything to protect the bike? I'd love to see someone lay the bike down on the side just to show what all would still get messed up if you went down.

@MacrossGarage

Жыл бұрын

I've see a couple videos of people laying the bike down with these. I believe the pegs touch first.

Does it decrease the inclination…?meaning scrape easier on curves due to less leaning angle.?

@MacrossGarage

Жыл бұрын

I’ve tired to scrape it and haven’t yet.

@chengsgroup2518

Жыл бұрын

@@MacrossGarage thanks bro ….just got a rebel 1100 in Taiwan… $20.000 USD …. . U guys a lucky….

@MacrossGarage

Жыл бұрын

Worth every penny 😉

Does that reduce your lean angle?

@MacrossGarage

11 ай бұрын

I've tried to scrape them while leaning and haven't been able to.

Would like to get it, but will it fit the Rebel 1100 Manuel version?

@MacrossGarage

2 жыл бұрын

I don't see why not. If it didn't Webike would probably mention it. You can always send them a message to be sure.

@my2wheels

2 жыл бұрын

@@MacrossGarage Hi again, try the link. Nothing came up. No listing of the engine guard.

@MacrossGarage

2 жыл бұрын

@@my2wheels I guess they changed the link. I updated it, it should work now.

Looks good, but it's a poor design being 2 independent pieces. This means any twisting forces will be transmitted directly to the frame which defeats the purpose.

@MacrossGarage

2 жыл бұрын

Yea I got to admit most of the reason was the looks and great for resting the feet on.

@MadMax-gc2vj

2 жыл бұрын

Wrong because Santa clause is coming to town.

Hey Macross what is the torque setting you used to tighten the bolts to fix the crash guard?

@MacrossGarage

2 жыл бұрын

I couldn't find the toque specs so please don't follow mine if you are particular about it. From my experience I think 20lb is plenty.

@binoyvaliyaparambath5759

2 жыл бұрын

@@MacrossGarage thank you

@MacrossGarage

2 жыл бұрын

@@binoyvaliyaparambath5759 No problem, you can also check on them every once in a while.

@binoyvaliyaparambath5759

2 жыл бұрын

@@MacrossGarage cool 👍

@stephenkk7bfg498

2 жыл бұрын

@ Binoy Valiya looks like the top tightening torque is 44N.m and bottom is 54 N.m as per instructions in Japanese

I tried this today and seems simple but I'm having trouble removing the lower bolt. The bike is on the kickstand.

@MacrossGarage

2 жыл бұрын

Is it not turning?

@jopierre17

2 жыл бұрын

@@MacrossGarage It won't budge. I'm well on my way to stripping it

@MacrossGarage

2 жыл бұрын

@@jopierre17 you using an extension or breaker bar?

@jopierre17

2 жыл бұрын

@@MacrossGarage I've tried both. I'm afraid of breaking it. The only thing I was thinking was the weight or angle but shouldn't affect the nut.

@MacrossGarage

2 жыл бұрын

@@jopierre17 it shouldn’t be that hard. As you can see in my video I used two open and closed wrenches. Sometimes you get unlucky and the loctite they use makes it difficult. If you uncomfortable, seek professional help. Maybe an impact air gun.

would this fit on honda rebel 500?

@MacrossGarage

2 жыл бұрын

Not sure but highly unlikely.

where did you get the headlight guard?

@MacrossGarage

11 ай бұрын

These are engine guards. Unless you are referring to another video.

What front wheel stand is that?

@MacrossGarage

2 жыл бұрын

I picked it up at a local Cycle gear called Trackside Roll On Wheel Chock

I am getting those this Wednesday. I live in Agoura Hills. Can you help with the install? I pay $200 for help…

@MacrossGarage

2 жыл бұрын

I would help you and wouldn't charge you anything you are pretty far away.

They say heroes wear capes. I say they wear blue latex gloves. Thanks for this!!

@MacrossGarage

7 ай бұрын

😂😂 you’re welcome

@TheAj0323

7 ай бұрын

@MacrossGarage I installed mine today. Went very smooth because of your video. Thanks again.

@MacrossGarage

7 ай бұрын

Glad it worked out.

Can anybody explaun why im having so much trouble taking the bottom nut off its not spinning and nuts are getting stripped

@MacrossGarage

20 күн бұрын

Are you holding it on the other end? The bolt is long and needs to be held on the other side with a wrench.

@satansspawn3012

20 күн бұрын

Yes

@MacrossGarage

20 күн бұрын

Does it look rusted or anything?

Don't you scratch when cornering?

@MacrossGarage

Жыл бұрын

No I haven’t. I’ve tried leaning hard and still hasn’t hit.

Plus bas la cloche, plus bas!

@MacrossGarage

12 күн бұрын

🤷

Where can I order them??

@MacrossGarage

3 жыл бұрын

Webike, link is in the dercription

Torque wrench should be used.

@fredelwell7997

Жыл бұрын

What's the torque spec?

This is for the DCT. I’m trying to follow but the manual looks different

@MacrossGarage

2 жыл бұрын

Interesting, I didn't know it was different. What part is different? Are you not able to install them?

@hecnotic

2 жыл бұрын

@@MacrossGarage I’m working on it now but the side of the brake. I believe there’s no plastic to take off

@hecnotic

2 жыл бұрын

It was easier if you think about it one less step to deal with. Clutch kind of got in the way adding the plastic back in back not horrible

@MacrossGarage

2 жыл бұрын

@@hecnotic Yea if there is no plastic it would be easier. That plastic near the brake is the one that covers the horn area and lower nut for the bolt mount?

@hecnotic

2 жыл бұрын

@@MacrossGarage the rear brake side. No plastic needs to be taken off. On the side of the clutch for me where the horn is. That plastic needs to be taken off. After that. It’s easy. Thanks to your video big props to you for this. Only bad part is my guardian bell was on the bell so I had to take it off and put it back on

No locktite ? good luck.

@MacrossGarage

2 жыл бұрын

I will probably go back in and apply it in the near future.

Engine bolt did not come out that easy.the entire bolt turned an eighth then the nut stripped out on me.not as easy as it looks in video in my opinion

@MacrossGarage

2 жыл бұрын

Which bolt upper or lower? You are the second comment this week on how hard it is to take out the bolt. Wonder if the newer ones have a stronger torque. Were you able to fix it?

No - thanks

@MacrossGarage

2 жыл бұрын

It’s not for everyone

This guy talks to much

@MacrossGarage

2 жыл бұрын

:)

감사합니다 따라 장착해볼께요

@MacrossGarage

Ай бұрын

You’re welcome

Very good information vedio....😊😊😊

@MacrossGarage

11 ай бұрын

👍