Thanks for carburetor adjustment advice. My craftsman 27cc blower was almost impossible to start and had to run on full choke. The repair place wouldn’t even look at because they said they couldn’t get parts and a new carburetor was over $100 to buy. I was ready to pitch it when I found your video. I purchased the adjustment tool for under $10 and did the adjustment according to your video. Runs great now. Thank you, Thank you.

Perfect video. Thats the exact blower I have and mine is doing the same thing.

Nice simple video that showed me exactly what I needed to know. Thank you.

@smallengineguys

2 ай бұрын

Glad it was helpful!

Mine is a mess. I cleaned the carb. New gas line. Idle adjustment screw- and it wouldn’t stay running. Boggs out. Now I know where this setting is I’m going to adjust it and keep my blower out of the landfill!! Thanks.

Grasias por este video y Grasias al maestro para mi es de mucha alluda porque tengo esta sopladora que tenia este ploblema

Thanks, great Video Liked way u showed What was Going On Keep up Great Videos..✌️🇺🇸✌️

@smallengineguys

Жыл бұрын

Thanks, will do!

Magnific 👍

Thks I just needed to know what one was high an what one was low.thk you.great job

@smallengineguys

2 жыл бұрын

no problem

Damn what kind of tool are you using dog gone !!!!!! good video

@smallengineguys

5 ай бұрын

amzn.to/3RCcyxc

Great job with the video - gave me confidence to try it myself - very first time - I have the same model - can you gave the link thanks

@smallengineguys

2 жыл бұрын

In the description but here amzn.to/30knAxc

I have a question. I work on carburetors quite often, but this one has me stumped. Doesn’t matter where I adjust the screw too It typically revs up really high and will die out. Then it won’t start. It will stay idling, but then it dies. I’ve tried every combination of every adjustment and I’ve had enough. Any tips??

When you cranking the engine witch way is the motor rotation

Hey I finally , with your help, installed the new carburetor !!,, It starts fine but when I release the trigger she shuts down - I panicked and adjusted both the settings the fuel air and either way - don’t remember - help!!!! Thanks

@smallengineguys

2 жыл бұрын

starting setting for the 2 screws is 1 full turn out from snug fresh. you needed to turn one closest to the engine counterclockwise just the slightest bit then the Philips screw is idle turn it clockwise till it idles

I replaced the carburator, lines etc. It won't start on choke or half choke, but does start on run. What am I doing wrong?

@smallengineguys

11 ай бұрын

i mean it starts right?

I tried adjusting a new carburetor but it keeps on turning off on idle/ bogging. So I decided to change the fuel lines and filter. Still does the bogging and turns off on idle . Any other suggestions 🤔

@smallengineguys

2 жыл бұрын

You need to adjust further. Or the muffler is clogged. Or your using old gas. Gas is only good for a 2 stroke for 2 weeks.

@davidlatino8986

2 жыл бұрын

@@smallengineguys how do I remove the the exhaust cap from the exhaust? I remove the plastic cover ...but I dont see any screws to remove the cap .btw I have the same blower model as you do....I replace the gas ... but I'll keep trying the adjustment screw.

@smallengineguys

2 жыл бұрын

@@davidlatino8986 i dont have one in front of me but there should be 2 bolts in the muffler. Probably recessed. Probably torque 25 type heads.

My parents have this leaf blower and asked me to fix it. Unfortunately, it came to me disassembled and I'm running into one problem. There's a black wire coming off the kill switch in the handle with an eyelet on the end. I cannot for the life of me figure out where it should go. Do you have any insight?

@smallengineguys

10 ай бұрын

It goes on the plastic part of the handle on the metal rod that curves to the outside of the handle I think

@southstreetbarbecue7875

10 ай бұрын

@@smallengineguys I couldn't find any metal in the handle, but that doesn't mean it wasn't there at some point before it came to me. I thought it was a ground wire but couldn't find anywhere to ground it! Thank you so much for the reply, I'm subscribed and looking forward to more videos!

@smallengineguys

10 ай бұрын

@@southstreetbarbecue7875 it is a ground just splice another wire to the motor

@southstreetbarbecue7875

10 ай бұрын

@@smallengineguys That makes a lot of sense. I love it when an obvious solution never occurs to me. Thanks again!

Do they have limiter caps

@smallengineguys

Жыл бұрын

No ill list tool when i get home tomorrow

What's your wrench?

@smallengineguys

3 жыл бұрын

carb tool amzn.to/30knAxc

Have no screw slots. Two places on the carb side by side no slots.

@smallengineguys

9 ай бұрын

speacial tool amzn.to/47Vw6UR

And how do you get them off

@smallengineguys

Жыл бұрын

Wait. Dude watch the video. Tool is in description.

Have this same blower doing the same thing

@smallengineguys

3 жыл бұрын

Easy fix. Common issue

@bflo716

3 жыл бұрын

@@smallengineguys good to know! I just won this at an auction for $30, looks like new, no rust or dirt. Should I spend the $15 and order the carb too or should the adjustment take care of it?

@smallengineguys

3 жыл бұрын

@@bflo716 try the adjustment first.

@bflo716

3 жыл бұрын

@@smallengineguys it worked!

@smallengineguys

3 жыл бұрын

@@bflo716 yep! Kinda my jam! Lol.

Sounds too rich to me. A bit more air might help.

@smallengineguys

Жыл бұрын

nope

that machine takes oil