Thank you for showing this video of disassembled 125-135. I needed a barrel swap because mine bent upwards. After watching this, I did it in a snap

@MrSteppingstone888

6 жыл бұрын

awesome. Are you in the U S I could use the barrel block, let me know thanks Mike

A mans gotta do what a mans gotta do. Your heart tells you what is right, good on you Mike. I would expect nothing less from you.

@MrSteppingstone888

6 жыл бұрын

Thanks Paul. hey is that a real picture of you? and what pellets rifles are you into, just thought to ask and where are you from

@thomaspauld

6 жыл бұрын

Yes it's my picture, only taken half my lifetime ago. I use a PCP BSA Buccaneer 20 FTP in .177 & a Crosman 2240 pistol in .22, I'm from England but for the last 12 years I have lived in Thailand.

Thanks Mike..I guess that put a stop to my crazy notion of having a break barrel rifle that could break down compact..Thought I could replace pivot bolt with removal pin w/ring and mod a folding stock...to pack in a backpack..oh well..

@MrSteppingstone888

4 жыл бұрын

It would take a special design & high quality steel to purposely make a rifle to disassemble in a quick break down fashion, but to try it with a already made air rifle would result in problems, like accuracy & P O I shifting. usually with a air rifle once the shooter has it gone over internally so it had the T L C custom parts & fresh lube usually they will have it scoped & dialed in and they will Rack it as is for next time , otherwise every time you put a scope back on you have go thru it all over again spending a lot of time

As always thanks for the great info it always helps us guys out I just did the seal on my 135 vortex .22 refurbished I bought and I had no issues with replacing the seal ...

@MrSteppingstone888

6 жыл бұрын

That's good, who's piston seal did you use, and Thank you

@airgunnersedge4061

6 жыл бұрын

Mike Ellingsworth** Mr Stepping Stone*** piston seal from air rifle headquarters

@bernardvanderveen7656

6 жыл бұрын

Now with the weihrauch seal im use the sound that when piston hitting the end is gone. Also up the fps.

@MrSteppingstone888

6 жыл бұрын

what caliber was the hatsan 125 you used the weihrauch piston seal where are you located. Thanks

@bernardvanderveen7656

6 жыл бұрын

The 125 have 29mm seal mine 135 30mm seal same size as hw 35 hw 80 hw90

Mike, I've done this without the locking system in place so putting the barrel back "open"..... saves messing about ....still center as you do with the large pin to ensure the shim is central. hope this helps mate

@MrSteppingstone888

6 жыл бұрын

I recommend having the internals out but had to let others know it can be done this way also, because I originally said it could not be done with the internals in bit that was because the barrel was open so I was correcting the info I put out in the older video on the same thing

Man I think my seal just gave way. Now when I go to discharge the weapon, it makes this fizz exhaust sound and doesn't discharge the. 22 pellet. I hope this video has given me a way to get it repaired. Thanks.

This is exactly the way I did it. But when I was putting the barrel back and tryed to put that screw back, the jam's spring tension wouldn't let me. The same situation you have here...so I closed the barrel, place it vertically on the end cap and pressed the barrel down with one hand. When those holes in the block got in line with those on the forks, I just put the screw back with my free hand. Well, it worked with my gun...

@MrSteppingstone888

6 жыл бұрын

It was worth sharing that it could be done / because that other video I did would be partially incorrect because I had the barrel open in that one. Thinking out of the box is what I try to do and also finding out for yourself is a good thing because you learn that way. Iam the same way / now others may be able to swap the barrel if they are capable enough to do it without knowing how to remove the internals / they have you to thank for that so good job and thanks for letting me know

Hi mike im also problems with piston seal. I fixed by modified piston and fit the weihrach vortex piston seal its now works perfect with 110kg gasspring and 5mm more stroke. H 135 qe with 125 barrel .25

@MrSteppingstone888

6 жыл бұрын

Thanks Bernard I passed the info on to some air gunners with that same problem

@bernardvanderveen7656

6 жыл бұрын

Mike Ellingsworth** Mr Stepping Stone*** hi mike yes first i tryed the h 135 seal from custom airseals it broke up. Then modified the piston now vortex weihrauch seal. Only thing now to get a .30 qe barrel.

Hi Mike-I enjoyed your video on replacing barrels. I’ve been wanting to replace the .30 10” barrel on the Hatsan 135 Carnivore with a .30 cal longer barrel of at least 20”. I think that will increase the fps and thus fpe. Any thoughts on this?

@MrSteppingstone888

Жыл бұрын

Hi Simon. yes the hatsan 10" barrel is ridiculous click the (about ) tab on my channels page, then scroll down for my email

hello mike 'I just set up a peace of 3/4 inch ply wood out at 60 yards and shot it with my hatsan 150th torpedo it went clean thru every time 'seems to have a lot of power 'don't you think?

@justinusberger3933

5 жыл бұрын

I have been watching a ton of youtube videos on air rifles lately. Looking to get a Hatsan 95 as a starter rifle. I've seen you around quite often in the comments. It's pretty cool to see a girl that is into air rifles. Not a creeper, just thought it was cool. lol

Hello Mike. Could you do a video on the 85 Vortex sniper, Im having troubles getting the anti-bear trap reinstalled after I had to tear it down to change the piston seal... More specificly how to reinstall it. I see this gun doesnt have it as it attached to the cocking arm on mine.

@MrSteppingstone888

4 жыл бұрын

here is my email send some pictres of the part you are having trouble with so Iam clear, I dont have that rifle but if its like the others it should be doable send to my email awaysmike@hotmail.com

The original hatsan seal is made from kind of hard plastic compared to the aftermarket seals maybe this will cause the burning also. I modified several Hatsan's 135/155 with a james macarri aftermarket seal. Did put the seal in it for a UK made Webely Patriot. They fit well. Just had to made a custom adapter to be able to mount it onto the piston. Just wondering if it would be an idea to hone the receiver tube with a hone device, this will make the inside of the tube able to stick the lube in a better way.

@MrSteppingstone888

9 ай бұрын

Usually I ll hone out the entrance of the tube a lot and go thru all the slots and holes and some in the cocking slot area. but inside the air chamber I will inspect it first often there enough micro scratches for lube to get burnished into, if I do anything more in theses big hatsan magnums its a careful quick cross hatching using a mini three blade flexible hone in warm soapy water running it in and out in air chamber area quickly for no more than eight seconds. you need the air chamber to fit the seal as snug as possible so you don't want to hone the whole area down others have mod the piston button and installed a 30mm Vortek Vac seal but you need a lathe and I have done similar with other guns

@mauritsjupiter2584

9 ай бұрын

@@MrSteppingstone888 Yes exactly, it needs micro scratches as you state. I just wonder what would be the best grid size for the honing stones. I found a honing device in my local tool shop with grid/roughness 60, 80, 220 and 280 those are used to hone engine cilinders and hydraulic brake cilinders. I have a lathe to make modicifations. Also planning to make an internal shock absorber within the piston.

@MrSteppingstone888

9 ай бұрын

@@mauritsjupiter2584 you can find the small flexible hone on Ebay even a fine one will work but be careful you dont want to over do it I have used those to hone out air chambers when they had a irregular over tight spot causing the piston to hang up. if you have a 135 you can lathe your piston button to fit a Vortek Vac piston seal and make it so it expands the seal more for a better over all shot cycle. vortekproducts.com/ourstore/

@mauritsjupiter2584

9 ай бұрын

@@MrSteppingstone888 I went to the website, it looks good stating it is a self lubricating seal. Unfortunately they charge $72 to ship to europe for this tiny item that costs only $18

Among my airguns guns I have this 135 in .25. Its more of a novelty that I bought because its oddly satisfying to put holes in stuff with one of the worlds most powerful brake barrels - childish as it might be. Anyway, basically what you are telling me is that I can put a 135 .30 barrel assembly on it and make even bigger holes in stuff, correct? Now, where do I get my hands on one of those?

@MrSteppingstone888

6 жыл бұрын

In the USA nowhere, hatsan won't sell a barrel assembly I had not had a 135 .30 cal to confirm that you could put that on a 135 / .25 I dont see why it wouldn't switch out, but you never know until you actully see it f because manufactures do weird stuff at times. you could google search outside of the U S and see if you can find parts that ship to the U S if its worth it to you, probably be better off buying a 135. 30 and be done with

if a seal is playing up try boiling or should i sat simmering for 20 minutes. place a suitable something to prevent the seal sitting on the base of the pan i use an o;d wire mesh tea strainer .... we British have daft thing like this hanging around lol ... hope this helps mate Dave

@MrSteppingstone888

6 жыл бұрын

I always boil mine to in the microwave what is occurring is some guys are getting new seals from both vendors and they are not giving them the fps as the original factory seal, they are not cheap and some have bought like four new aftermarket seals with bad results.

Hey Mike I got a torpedo sniper 150 you know of any place where I can get a spring and a few things to tune it up. Mine sat for some time and the spring broke

@MrSteppingstone888

11 ай бұрын

Hi Nick You can go to Hatsan USA.com once there click the Warranty and safety Tab. that will open the drop down menu but you have to scroll down to see the full drop down list , click on Product Diagrams/ once there scroll down to your under leaver model hatsanairgunsusa.com/wp-content/uploads/2018/12/Torpedo_150-Exploded_View-June2013.pdf then pull your part numbers and go back to the home page then click on the Contact US tab when drop down menu opens click the Customer service form fill it out, add your part number and name of the part off the diagram and summit your request, it may take 4 days before they reply just be patient they will let you know what they have available

the small retaining screw to remove it is it anti clockwise or clock wise?

@MrSteppingstone888

8 ай бұрын

Hi The small locking screw is normal counter clock wise to loosen it

Hi Mike... I just subscribed to your channel.. I have a Hatsan Mod 130S and it seems the gas piston and seal have went bad... It's this something I can order parts and replace myself..?? If so, where do I order the parts from and do you have a video showing how to do the replacement..?? Thanks.!!!

@MrSteppingstone888

Жыл бұрын

Hi John. those gas rams fail a lot and I have been rebuilding them properly even if you got another from hatsan it will eventually fail you. Now I have my own custom piston seals for those , they make the shot cycle smoother and the piston edge will not burn off and typically you get your full feet per second its a very nice upgrade for a hatsan magnum. the guns are a royal pain to work on In all honesty John contact me via email go to my channel click the abut tab and scroll down you will see where it says email I can go thru that entire gun and get it done etc.. use my email for further info Thank you Mike E.

Hi mike got me few Hatsans (pcp)'s want to add another springer I Have a crossman springer / really like the 125 Hatsan could you tell the best after market spring to use to tune it and were i can pick one up please' and also any other parts that will work well with that ect " And what are you using your self l to lube the new spring with ... ?.. What do u recommend. Many thamks 👍

@MrSteppingstone888

4 жыл бұрын

well the aftermarket spring would come from Vortek products Ill add the link, it's a full power spring so it wont feel tuned you can have a custom spring guide made I do them with a top hat its better tan factory guide in it will fit properly you can always detune by cutting a coil far as piston seals I recommend the hatsan seal from hatsan usa the aftermarket seals have been failing unless something changed I don't bother with them , I don't bother cross hacthing on a hatsan / I lube them using ORIGINAL Super Tech ® Multi-Duty Complex Hi-Temp Grease - 14 oz - 4 Pack I clean out the receiver tube using break clean spray and you need to ream the hell out of the end of the receiver tube and use a thin small screw driver to help tuck the piston seal past the places it will get nicked. here are the links ORIGINAL Super Tech ® Multi-Duty Complex Hi-Temp Grease - 14 oz - 4 Pack www.ebay.com/itm/ORIGINAL-Super-Tech-Multi-Duty-Complex-Hi-Temp-Grease-14-oz-4-Pack-/113575718707 vortekproducts.com/ourstore/airgun_springs?product_id=256

@SNATCHYDBS

4 жыл бұрын

@@MrSteppingstone888 thanks mike will order that from Vortek" can i get your custom guide ect from you and were do i order from is it a link through your channel or web site. ?.. many thanks . Mark

@MrSteppingstone888

4 жыл бұрын

@@SNATCHYDBS well I could order your vorteck spring and make the guide for it with a tophat contact me via my email with your info ( no spaces & no caps ) here you go awaysmike @ hotmail .com

Mike I have a Hatsan Edge, and I have a question about an item on the barrel (I'd like to remove). If I send you a picture can you tell me what it is and if it's OK to remove it ? There is no description in the owners manual. Thanks Dan

@MrSteppingstone888

3 жыл бұрын

Hi Dan sure send me a email with picture awaysmike@hotmail.com

Hey Mike, Do you bore & re-rifle barrels? I have a .177 Gamo Magnum that is way over powered.. just wanted to know if you can make it a .25 Cal barrel? Or know where I can buy a Gamo socom extreme.25 Or Hunter extreme .25 barrel? Thanks

@MrSteppingstone888

6 жыл бұрын

The Gamo magnums have non steel barrel blocks some sort of abs plastic, so no touching that. Gamo did not make the .25 in these models it was ridiculous they just wanted to show feet per second because speed sells I can rebarrel the hatsan magnums but I will not take on any work because I work 5 days a week and need the time to do my thing

Can you direct me to what video you show the proper way to install barrel pivot Bolt I had a helluva time a couple weeks ago installing on my cometa fenix 400 had a heck of a time lining it up even with my tapered punch I ended up stripping the threaded side of the fork but I was able to put the Bolt in the other side and tighten it down to clean out the threads and I eventually got it back together but I need to take it apart again , to put a new piston sale and do not wanna go through that again any help would be appreciated Mike

@MrSteppingstone888

3 жыл бұрын

Hi sound like you are trying to install the barrel block with the internals in place with the cap on. it is best to remove the end cap and spring tension or ram so the barrel and cocking arm is free to shift and I use the tapered punch sometimes I have to slip it thru the barrel bolt hole on the fork then while its still inside I carefully flip it over and slip it thru the opposite side to get it aligned up. with that you can get the bolt thru then install the internals. I did do a video with out pulling the internals but it is to difficult and it also depends on what gun it is and its best just to have the internals out

got my 135 qe vortex .177mm had it for a few months shot it a bit and had it stored for about a month and jus took it out and went to cock it and got no compression at all.. jus falls.. i watched this video and got it apart as you instructed and i can see where the linkange connects and i can slide the piston i believe back and forth….im stumped how what to do further. do you have a video on a135 full break down? thanks man

@MrSteppingstone888

2 жыл бұрын

You need to send me the gas ram and I will rebuild it properly/ Thanks awaysmike@hotmail.com

So the 125 .25 springer came in today. Two questions is the trigger supposed to be loose side to side maybe 1/4 in. Play. And also can i put a metal suppressor on. This hatsan. And do away with the plastic crap

@MrSteppingstone888

3 жыл бұрын

Yes the quatro trigger has that play side to side you'll get used to the feel of it the only wat to remove the plastic suppressor is to cut it off with a Dremel, its pressed fitted on , how you work the new one is up to you .to work out but clean the barrel first with go gone & 3/4" cotton patches and see if you have a good barrel

What you recomend, spring or vortex gas ram ?

@MrSteppingstone888

5 жыл бұрын

if your able to do your own work a spring. its a matter of personal taste and trying them out to see what you get from each

Mike are you still in business? I need help with a screw removing whole barrel and trigger and piston seal, screw head is ground out and will not take a screw driver. How can I get that screw out? The one that also screws to strap holder.

@MrSteppingstone888

Жыл бұрын

You will need to reach me at aways mike at hot mail dot com no caps no L no spaces and use @ sign and use the small .

I just purchased the .25 vortex and was wondering if and how the dovetail combo can be swapped as it won't work with my chosen setup

@MrSteppingstone888

2 жыл бұрын

that is spot welded on. you have a dove tail with stop pin hole I would use a 4 screw minimum one piece mount with stop pin If you have use the weaver slots with separate rings #1 inspect the slot at the bottom that the rings will be used in and be sure they are machined cleanly & square, some have come out not correct. and if yours is good I push the front ring towards the barrel when in the slot then tighten & the rear ring when in the slot towards the butt end then tighten that way you are covered for rearward & forward re coil which you have a lot of forward recoil also be sure to clamp rings so the gaps between half's are even & scope is level with top of barrel block I use two levels one on the barrel block the other on the scope hope the info will be useful I never know what a persons knowledge base is/ you need a good springer rated scope or your reticle will shift if your barrel happens to be a good one I use a zeroed scope ( reticles are in the center adjustment ) then adjust the barrel to the DOT I am aiming at by bending the barrel carefully after each shot till I get as close as I like

@Billy-lx1gx

2 жыл бұрын

@@MrSteppingstone888 thanks for the info

is it a vortex gas ram ,I bet it failed. I rebuild them , if it failed get bck to me

Hello do you have any idea why my Hatsan .25 vortex break barrel suddenly wont cock? There is no resistance . When i break the barrel it just fall over!

@MrSteppingstone888

2 жыл бұрын

Hi Santo Yes the gas ram has failed ! I rebuild them and now have custom parts for the hatsan magnums that I have to install if you are Outside of the US and need the gas ram rebuilt properly let me know you can contact me hear awaysmike@hotmail.com

Hello Mike . I have a couple Hatsans that are in need of an overhaul. A 125 .25 and a 135 .22 . Can I send them to you?

@MrSteppingstone888

2 жыл бұрын

Yes you can email sent.

sorry me again.... i use dry graphite powder.... works a treat rather than grease ...

Can I use a crosman spring for mi hatsan edge

@MrSteppingstone888

5 жыл бұрын

Hi I do not know/ normally you would take your spring out to measure the dimensions and look for something that would come close

Where can I get a spring for a Hatsan95 ???

@MrSteppingstone888

5 ай бұрын

I have one see if you can pul my info . Go to my channel read the Sharing my passion for airguns, work done ,mods, re barreling, lathe work etc. and click the arrow symbol seen at the end of it >

hello mike 'do you know any thing about the hatsan 150torped ?'and can you tell me where I can buy a tune kit for it please?

@MrSteppingstone888

6 жыл бұрын

Hi Susan. I have not been into mine yet, no one is selling a tune kit for them, how ever if you are able to take it apart you could see what spring it has and see if vorteck has one that's close to it you know count the coils use a caliber to get the O D of the spring etc, I could make a guide for the new spring if they have something I charged 55. shipped back but I would need the new spring and your factory spring guide and info on the factory spring length and O.D. piston seal I would leave it unless its totally messed up I think because you be gettng rid of the crap factory oil and re lubing it yourself the seal would probably be fine

@susanmarie4257

6 жыл бұрын

I got one from vortex for my hatsan 125th '3 years ago it still work perfect 'I'm thinking it takes the same spring and seal as the 150th

I have one on the way should be here tomorrow. How can i test that i have a good rifle. I heard of a tp test for making sure the seal is good. Is there any other test?

@MrSteppingstone888

3 жыл бұрын

which model is it .& what caliber is it.? get some 3/4" cleaning patches from wall mart and a thin brass rod ace harde ware smooth & round over the ends and botte of goo gone clean the barrel good if you bought a sniper you have to open the hand break to remove the baffels or you will get patches stuck there's a 125 sniper video that shows how to do it. after cleaning the bore good run dry patches down to remove any excess goo gone. then slowly push a pellet down thru the bore ( SLOWLY ) lol you trying to feel & see what the pellet to bore fit feels like get pellet into breech and use a small punch or similar to get it in just inside then use your rod. / tilt barrel slightly not quite a 45 so the rods weight has no effect on pushing the pellet but is heading down. If the pellet slides thru with no contact in a few spots but then you feel a light pellet drag that normal ! Ideal would be consistent light pellet to bore contact, but free fall totally loose in most of the bore is bad consider that a bad barrel / use only one layer of the tissue when you do the breech seal test sniper video marker at 5:min in kzread.info/dash/bejne/dXWdw8aiiNLYj8o.html

@medee5712

3 жыл бұрын

Thanks for the detail. It is a hatsan 125 sniper

@medee5712

3 жыл бұрын

.25 cal

@MrSteppingstone888

3 жыл бұрын

@@medee5712 Perfect thats the best caliber for those big magnums the shot cycle is smoother then the .22 due to size of the bore & .25 cal usually the bores come out better then the other .22 so you have a good chance of getting a good barrel

@medee5712

3 жыл бұрын

@@MrSteppingstone888 hell yeah!!

Does slop in the barrel pivot cause accuracy problems?

@MrSteppingstone888

5 жыл бұрын

If its a hatsan 125 / 135 where the power level is extreme, I would think it could, due to the barrel blocks lock up slightly changing every time / I had friends have a machinist make them a new bolt just a tad over size so they had to just lightly sanded them down to get a fit then they cut their own groove where the tiny set screw needed to be. the hatsan pivot bolt is a odd size

@Ryland35767

5 жыл бұрын

Thanks for the information and your videos.

@MrSteppingstone888

5 жыл бұрын

Your welcome and thanks for the pos input

Hatsan 95 Vortex break barrel.

Mike.... You live in Billings?!!? (MT.) I'm from there, also. I'm thinking of buying a Hatsan 125 (.22 cal) from a fellow member on the GTA Forum, with less than 200 shots through it for $150. with the sling (never used), and several tins of JSB pellets, the original box, etc. It is less than a year old and he bought it from PA. I already have over 35 in my collection, but No Hatsans.... my spring guns (28 of them) are all German (Weihrauch, Diana & Walther) except for four Xisico's that I bought fully tuned from my friend, Mike Melick... who is very well known for being the number one Chinese Airgun tuner in the US. Anyway, Mike... am just wondering if buying and adding a Hatsan, especially the 125... to my collection is Really worth it, just to have a Hatsan.... what say you? : )

@MrSteppingstone888

6 жыл бұрын

You have to clean the bore with the goo gone then do a pelet to bore test by pushing the pellet down the bore slowly with a thin rod so it won't push against the skirt giving a false reading if the bore is ok fair or good and seems to group well then you could spend more to have it gone over. Normally I wont do it because I work 5 days a week and I just dont have the time normally people ask and I send them to my friend Rich and he will send the trigger to me if the customer wants to pay the 55.00 for it to be done & shipped back to rich. personality unless you have money to burn I would not bother between shipping back & forth and vortek parts etc/ see if the barrel is good and let me know

@justinkase3355

6 жыл бұрын

2Stroke Diesel Power hats agood deal i judt bought my whole combo 299

@MrSteppingstone888

6 жыл бұрын

Did you buy that 125 from the gta member

👍👍🇦🇷🇦🇷

@MrSteppingstone888

3 жыл бұрын

Here is the video on that R - 9 I mentioned and what the dealer did to it that made it not work kzread.info/dash/bejne/qpqTypiqmd3SaJc.html

How to connect you

@MrSteppingstone888

4 ай бұрын

Go to my channel in the banner read where it says Sharing my passion for air guns, work done ,mods, re barreling, lathe work etc.> Click the small > and it should show you email info

Mike , help, I like my hatsan 125 synthetic stock. Can you fix my gun. I am dissasembeled, have the shock it’s from Russia and I’m lost. I need your address please

@MrSteppingstone888

3 жыл бұрын

Hi Paul email me at awaysmike@hotmail.com

Original Hatsan seal and moly lube.

@MrSteppingstone888

3 жыл бұрын

Hi Rick the gun are built beyond the piston seals ability to maintain the best seal they all wear in & level off showing feet per second below of what the gun is capable of getting/ But once the factory lube has been changed out the hatsan seal will last longer then normal . people used to use molly and burnish the reciver tube on typical airguns of high quality but hatsan magnums are not your standard weihrauch german gun and piston seals should never be taken down for sizing like on some german guns Instead the rear of the receiver needs to be rheem & honed out for enlrgement & smoothness so the new seal wont be damaged or nicked Lube wise no more croshacthing & molly ,instead I burnish the reciver with a different lube carefully with a home made tool like in this video 13:55 into it kzread.info/dash/bejne/g6Zs1ryMnJm7gaw.html

@RickDelmonico

3 жыл бұрын

@@MrSteppingstone888 Just ordered a 155 vortex referbished in 25 cal. Found this, www.gatewaytoairguns.org/GTA2/library/Springer_Airgun_Lubing.pdf

@MrSteppingstone888

3 жыл бұрын

@@RickDelmonico Hi Rick Yes I know the old school set in stone ways for croshatching and lubing guns/ and for years no one dared say or do anythng different. air guns & forums can be such a snitty world . "comes down to common sence, " burnishing molly is not the only way or only the proper way it simply was the old school back in the day way some use krytox in that case they polish the tube instead of cros hacthing etc Often guys who burnish the tube with molly dont even do it properly btw it was the old school info that we all learned & started from and it progressed from there

Mike great videos, but this is a question about where to get parts for a Hatsan 95 Vortex, can't find the correct filler port tube and nobody at Hatsan USA has the time to answer the phone, very rude. broke down my 95 and pulled the gas tube, ordered a filler valve from Hatsan and after the order was placed I saw a PCP valve on the order , will that one work on my 95? Also do you know of any place to buy parts for the 95 Vortex? Doing a trigger job or clean up while I wait to see if it will ever shoot again. Thanks and as before yours are so good , or should I say great. Thanks

@MrSteppingstone888

Жыл бұрын

Hatsan usa has request forms to fill out to request parts they will not sell you a barrel assembly. did your ram loose power they eventfully fail and I rebuild them properly so they wont fail like the factory one do. I do not know what you ordered but a pcp pump & fill probe that goes into the rifle or gas ram is needed/ the probe has two O rings on it it lets air out & seals it from leaking during filling 150 bar is all you want any more just adds more recoil. hatsan usa has model diagrams you get your model & find the part name & Part number and fill out a request form if you buy a new gas ram it will eventfully fail you can send me your ram I rebuild them properly awaysmike@hotmail.com

Mine ripped sucks

@MrSteppingstone888

Жыл бұрын

Hi Steve You can buy the metric tap from ace hard ware and also go to hatsan usa click on the TABS at top & look for the parts diagrams to get your part number & fill out a request form to get another bolt. I hate this video I may delete it and do another one later

I just want to test the gun to make sure everything works as it should. so i have a fear im going to get that 1 f up out of all the diamonds.

@MrSteppingstone888

3 жыл бұрын

Absolutely your buying a hatsan lol I sent you a reply with good info

@medee5712

3 жыл бұрын

What parts do you recommend keeping on stand by for the hatsan 125 springer

@MrSteppingstone888

3 жыл бұрын

@@medee5712 the vortek after market spring / but not for the 125 as he list but the 135 thats the one you want. I have them if your looking to get one. vortek may stop making them he dropped the piston seals "Are you in The U.S.

@medee5712

3 жыл бұрын

@@MrSteppingstone888 es sir im in the U.S.

@medee5712

3 жыл бұрын

Yes