These videos are some of the best on You Tube on any subject!

@dougsworldtour3755

Ай бұрын

Thanks Jim, I try to keep things simple and to the point, not much fanfare. :).

Hi 👋 again! Nice to see this video. The problem with the first BA was one of the input led detectors of the upper sensor board. I remember when I first replaced a belt in one of those several years ago 🙃🙂... That bill acceptor was the first made of plastic, won an industry price for the design back in his time. 👋

Helped me out a lot. Thanks!

@dougsworldtour3755

2 жыл бұрын

Great Scott, I'm glad, this is one of my top videos. I guess there a lot of Coinco's still in service. Stay tuned for more.

Heybthere great stuff! My unit first started eating bills and not giving credit. The black plate tray on the inside that money box sits on is sort of loose on the top where in my older model its much tighter and stays flat. I can’t figure out what it is. Also it started running rough when accepting the bills.

I have a change machine that has a three pulse red light that says: “check bill path” the bill path looks fine. The motor that sucks up the bill engages on startup and when you press the reset button but not when you try to feed a bill.

@dougsworldtour3755

2 жыл бұрын

Usually a bad sensor. We can repair those. lasvegascoinop@gmail.com

I have a VM-010 change machine its giving out 8 qtrs when we put in a dollar bill. What can we do to fix this. TIA

Hey Doug.. I have a Coinco BA30BB in a DN 276E thats not working. 5 blinks. Cant get it cleared. What models can I use in this machine. I only need $1 acceptor.

Great video. I have a question: My Dixie Narco 501T multi-price soda machine is using a BA30SA bill collector that only accepts one bill per vend (price is set to $1.50), requiring coins for the balance vs taking a 2nd bill and giving .50c change. When I adjust the escrow (ESC) settings in the machine the bill collector will accept a 2nd bill, but only once. The next purchase it goes back to one bill per purchase. Do you know why this might be happening?

@dougsworldtour3755

Жыл бұрын

low coins in the tubes or there must be a setting in the admin area of the machine itself.

I have a crane gpl 159 snack machine and has this same bill validator can you give me the kit for to use new mei?

@dougsworldtour3755

3 жыл бұрын

This is the unit, it takes 1s and 5s, be sure tom order a power cable to hook it up to your system, they are listed under "options". I am guessting that your system is already MDB with a 6 pin plug for the coin mech? If so your good to go, all plug and play. lasvegascoinop@gmail.com

hello, can i replace the Coinco BA30B Dollar Validator with a better unit? if so which one you recommend? or , do you have a refurbished units for sale? thank you.

@dougsworldtour3755

3 жыл бұрын

yes you can, a MEI is a far superior bill validator. I have everything listed on my site. dougbaleenterprises.com I'm here to help.

@aceju1

3 жыл бұрын

@@dougsworldtour3755 It will be just plug and play? Don't need to do any programming?

@dougsworldtour3755

3 жыл бұрын

@@aceju1 nope, plug and play

@aceju1

3 жыл бұрын

@@dougsworldtour3755 great! I will buy one today Thanks for your help

@dougsworldtour3755

3 жыл бұрын

Did you figure out what you needed? I can assist if needed. lasvegascoinop@gmail.com

Hi Douge, I’m hoping you can help me i would pay you for your help. I have a ICT type 6 bill collector When it takes a bill it does not push it into the bill box and i have to take it out and it’s resets. Any suggestions

@dougsworldtour3755

Жыл бұрын

Bob, those to put it likely are "junk" always were and always will be. When they quit, throw them away and replace it with a quality MEI unit. Your troubles will be over. I have everything you'll need. lasvegascoinop@gmail.com

@Bob-jg8kg

Жыл бұрын

@@dougsworldtour3755 Thank you that’s what I’ve noticed. I’m new to this. How much is a ICT 6

@dougsworldtour3755

Жыл бұрын

Bob, best to replace it with a MEI, your troubles will then be over. The ICTs were not good even when they were now. lasvegascoinop@gmail.com for help

Hello Mr, How I can buy the spare parts? I tried the website is not working.

@dougsworldtour3755

6 ай бұрын

we receive 25 orders a day, here is our site URL. dougbaleenterprises.com Stay Strong!

Can I ask what kind of tester that is that you use?

@dougsworldtour3755

2 жыл бұрын

Mine is the "Vending Pro" by SEM out of Canada. The model is CT3, a little pricy at about 1000 USD but its a necessity..

hello< do you have a video repairing a lower or upper drive motor on a Coinco validator?

@dougsworldtour3755

2 жыл бұрын

sorry but I don't, they can be tricky

@nery200043

2 жыл бұрын

@@dougsworldtour3755 they sure are, what the amps on a good upper or lower motor would be? If you not mind.

@nery200043

2 жыл бұрын

I need to sent some MEI for repair , how do I get those to you and rates please.

@dougsworldtour3755

2 жыл бұрын

@@nery200043 lasvegascoinop@gmail.com

Can I buy one from? you we need it for our soda machine at our church. BA32l

What does 11 blinks mean it doesn't take the bill .....

@dougsworldtour3755

11 ай бұрын

Usually needs service and a component has failed,

@laidback420

11 ай бұрын

@@dougsworldtour3755 .. I have 3 different ones here n can't get it to take a bill