Coffee bean serving tray - Servírovací tác s kávovými zrny
Музыка
Dřevo / wood: Ořešák černý / Black walnut
Epoxy: VEROPAL CLEARCAST 300
Penetrace / penetration: Veropal PEN
Pigment: Eye Candy Pigments - Cherry Red
Leštění / polishing: Finixa One step
Povrchová úprava dřeva / wood surface treatment : Howard Butcher Block Conditioner
Пікірлер: 35
Дуже добра робота. Гарна річ вийшла. Вже замислився своїй жінці таку тацю теж зробити. Єдине що - я б на торці дав би ще один фінішний шар смоли щоб закрити перерізані зерна. Бо з часом вони повисипаються. Хоча й пахнути будуть сильніше, ніж під смолою.
Super práce 👍🏻👍🏻👍🏻
This is one great video. There’s so many amazing videos out there. I never thought about using coffee beans ☕️.
Красивая работа!
В начале видео был замешан пигмент, а по итогу прозрачная смола. Смотрится отлично 👍 👍 👍
@nitronautcz
Жыл бұрын
Пигмент находится в нижней части. Это видно после поворота лотка :) Фиолетовый металлик. Спасибо
Nice video
Beautiful job!
Hey, in addition to woodworking, you are also a brilliant cameraman and director. Well done!
@nitronautcz
9 ай бұрын
😲 😊 thank you
I love it! I will make one someday.
this is really nice!
Love the idea but you should have kept the beans about half an inch from the edges so you don’t cut into them when squaring it up. Good video though!
Красиво! После шлифования нужно полировать? И что ещё добавить?
STE MOC SIKOVNY SKVELY NAPAD S KAVOU
very nice design, give me idea to make one
Looks awesome man, what product do you use to polish it up?
@nitronautcz
Жыл бұрын
Thank you very much and sorry for replying only now. I use Finixa One step polishing paste.
Amazing, I would love to make 3 of these for close friends. Do you allow the epoxy to harden before adding each layer? What grit sandpaper is best, and what is there a specific polishing cream you recommend?
@nitronautcz
7 ай бұрын
I let the first layer harden so that the grains don't float to the surface when I pour the second layer. If I had to do the serving tray again today, I wouldn't mess with it so much. I would use sandpaper with a maximum grit of 1000 and would not polish. I would coat the tray with a thin layer of epoxy and spread it out. This way I achieve glossiness and, above all, evenness better than polishing. I use Finixa One step polishing paste.
Was the purplish dyed epoxy at time 3:05 used? I missed seeing it in the final lookover.
@randyrenfro5907
6 ай бұрын
It’s the first pour where the beans were put in.
That looked like a solid mold, was it not? I'm asking because of the tape
@nitronautcz
2 жыл бұрын
The mold is made of 10 mm plexiglass and the parts are glued with double-sided tape. Unfortunately, I made the mistake of wrapping the inside with yellow paper tape. The tape peeled off after pouring the epoxy and I had a problem with it. So you can use insulating tape, but not paper tape. It is important to seal everything properly.
Do you sell them?
Price?
Hi perfect ❤❤ Can I ask what was that spray you use !??!
@nitronautcz
9 ай бұрын
Hi, thank you :) This separator is no longer produced and was only available for the Czech Republic. VEROPAL RA100
How do you know how much resin to mix up?
@nitronautcz
Жыл бұрын
I will estimate the ratio. I always prefer to mix less resin. As it has a long setting time, it is not a problem to mix :)
Great table, music was to loud
I see bubbles
3:36 Wasting coffee beans!!!!!! WHY DIDNT YOU USE PLASTIC INSTEAD??????????????
@nitronautcz
Жыл бұрын
Because it's low-quality and nasty-tasting coffee.
@ratheeexperiment4892
Жыл бұрын
@@nitronautcz hell sir where are you live .... i want to work with you, if you don't mind....