If you enjoyed this video, give it a thumbs up and subscribe. Comment below with any questions you have for me about the video.

@skottymacmac

5 жыл бұрын

Hey pal so how did you fix it . Did you just have to push it all the way in harder or did you buy something new ??

@boosthit811

5 жыл бұрын

@@skottymacmac Hi there, just saw ya comment. Yes basically just have to push the seal on completely. Been fine since.

I’m actually a full time mechanic and this even helped me out 🤣 The more you know! Cheers fella

You legend! Thank you! I've spent 3 days trying to stop my golf hydraulics from leaking... removing the o ring and pushing the cap down has sorted it! 2 hours to fit a cylinder followed by 3 days of leaking fluid and swearing. You saved the day ❤

@courbemusic64

Ай бұрын

I’m in the exact same position now. I’m trying this tomorrow morning!

@matteo512

28 күн бұрын

​@@courbemusic64same problem wirh mk4 golf tdi 150 😅

@courbemusic64

28 күн бұрын

@@matteo512 Worked for me

Thanks, it took you 2.30 seconds to answer a question I've been asking for 2 months!

Thanks - I had exactly the same issue. Spent a wasted afternoon dismantling the clutch thinking the leak was coming from the slave cylinder!

Thank you so much. I was about to set my van on fire. I’m also glad to see that I’m not the only one that couldn’t figure it out. I guess because the parts catalogue for the T5 VW shows the small o-ring and the cap/seal thingy both installed. Either way, I’ll give this a go. Thanks again and fingers crossed.

Saved me a tonne of headache today mate thanks a lot

I had the exact issue , after many attempts and lots of f words . Finally managed thanks to you .

Hello pal, just want to say thanks very much for your video. I was thinking about scrapping my car. I could not figure out why the cylinder was leaking. All solved now she will live again. Thanks again

@boosthit811

2 жыл бұрын

Ha Geez that's good to hear.

thank you, my new slave cylinder didn't come with a new seal and the old one was stuck in the old part. I didn't know that there was supposed to be a seal until i seen this video and sure enough put it in and it fixed my leak.

@babelonchabalala1690

Жыл бұрын

Seems there are a couple of us had the same problem.....old one stuck in the old unit without realising

VERY GOOD TO SEE THIS

Thanks. You saved me man

Perfect! Thanks

After removing the old line installing new line withouth removing bell housing, using custom made tools. working 2 days to swap the line it still leaks, found out due to your video my coupler is missing the citroen part no 215615. Was already thinking about making a custom coupler with a T piece to bleed etc.will try this for sure!

@Grandpasaab

2 ай бұрын

haven't tried yet, how doesnt brake fluid not leak inbetween the top of the line and the rubber?

Thank you so much!!!!!!!!!

So we don't have to remove transmission for this?

Thank you. I had the same problem. My slave cylinder is behind engine so I could not see proper only that it was leaking. 😅

Thank you

thank you

Will this make ur clutch fluid leke from the bottom of transmission 🤔

Hey bro have you had issues with the plastic elbow not fitting your throw out bearing?? Been in the process of a t56 swap for over a year now and this is the only thing from keeping me from finishing 😢 If you don’t get me I’m about to post a video on what I mean

@boosthit811

Жыл бұрын

Can't say I have.

Bonjou ,est ce que je peux retrouver ce pièce. Pour un zusuki grand Vitara 2007¿?

What is that rubber thingy you keep playing around with, where does it go, Does it come with the cylinder.What are you trying to show at the end, all i see is what looks like a finger pointing to the connectionz at the end of the cylinder? Thanks for the video.

@boosthit811

Жыл бұрын

That is the seal or seal example. The video is saying how the seal isn't installed out of the parts box. But it is sitting on the correct location! It still needs to be firmly pushed on to seal and locate correctly.

My goodness thank you

They could have designed the pipe to fit in from the top. Its a nightmare working on the firewall and sometimes the seal gets stuck inside the master

Just what I needed to know, nice one mate. One question, how did you get the elbow off ? I obviously lifted up the spring clip but feels like it's still not wanting to come off. Not expecting a reply, the video is 4 years old but you never know lol

@boosthit811

3 ай бұрын

Just working it back and forth and eventually it should come off

@marksutherland774

3 ай бұрын

@@boosthit811 Nice one cheers, I have an insignia but it looks similar design right pita, the clutch master failed, eventually got that sorted and then the problem moved somewhere else, fluid leaking from underneath but you could bleed it temp and the clutch would come back so not the slave so I am guessing it's this little bugger, thanks again you're a star.

Great video, I lost mine in the process of replacing the CSC.Any idea where you can buy the rubber "o-ring"?

@boosthit811

3 жыл бұрын

Thanks. Hmm dont know if they are sold on there own. Maybe have to get one from breakers/wreckers yard.

@boosthit811

3 жыл бұрын

Thanks. Hmm dont know if they are sold on there own. Maybe have to get one from breakers/wreckers yard.

@boosthit811

3 жыл бұрын

Thanks. Hmm dont know if they are sold on there own. Maybe have to get one from breakers/wreckers yard.

@matejcermak

3 жыл бұрын

This looks like the one I have, exactly, and I have in on Citroen Xantia 2nd gen.. the connection seems to be widely used between manufacturers, Citroen number of the rubber is 215615 and can be bought alone, and the black plastic on the pipe comes with the pipe. but you should of course check your vehicle parts catalog if you are not sure

hi i have a leak somewhere on my astra as when im bleeding my clutch it leaks out the bottom of the box i have looked and i have a oring but not the larger rubber you show on yours is it the larger rubber i need?

@boosthit811

2 жыл бұрын

It may have left part of it behind in the female end. Check with a pick. It should look very similar to in the video.

My whole elbow has a play (loose) about half a inch. Is this normal or should it be completely solid. Slave cyclinder is inside the transmission, elbow is ride outside.

@boosthit811

2 жыл бұрын

It sounds a bit excessive........

Thank you. Gonna try it. Have same leak. I replaced the bearing like a year ago didn't have any problem till now. It started to leak, but the seal is in that plastic elbow. Maybe someone knows the part number for new seal?

@jayjay-bi7me

5 ай бұрын

Did you get the part number for the seal

@daggrag

5 ай бұрын

@jayjay-bi7me Baugh from ebay, just typed clutch seal. Those seals fit to other cars to.

😂😂😂 LMAO at myself for wasting an entire day trying to figure why its still leaking when i try bleeding.......Low and behold.....this video was Godsent.....finally put that seal on the right way and got the car out my garage 😂😂😂

@boosthit811

Жыл бұрын

Ha yeah, it's surprisingly common 😄

Is there an oring aswell that is installed with this seal?

@boosthit811

3 жыл бұрын

No not on this one.

@babelonchabalala1690

Жыл бұрын

I have problem with the one that O ring as well

Bro how do you reinstall with that metal clip

@boosthit811

2 жыл бұрын

They just push lock

Hello, kindly assist me, I try moving my car this morning and when I try to get it in gear it won’t even move but the reverse gear would make a very loud noise, but after a few minutes of turning the car back off and going back to try to move it, I put the car in gear before I started the car and it worked just fine. What do you reckon the problem would be ??

@boosthit811

3 жыл бұрын

Sounds like you are "losing the clutch pedal" try bleeding it or get it to a shop to diagnose her....

@claudiokoning6501

3 жыл бұрын

I have the same issue. What was the problem in the end?

@thespiritualwayofallthings

Жыл бұрын

Yeah this happened to me, first and reverse wouldn't go into gear, so did what you did, put in gear before start and is fine. But weirdly it's stopped, so gonna bleed the clutch see if it helps if not possibly the clutch may need looking at, you get the odd cowboy mechanic who dont put the clutch in right. Hope you get sorted

@thespiritualwayofallthings

Жыл бұрын

Oh make sure you haven't got a car mat under clutch. It can make a big difference as clutch pedal doesn't go all the way down.

Is there a tool to remove the plastic fitting?

@boosthit811

2 ай бұрын

Not that I know of

How do you remove that elbow?

@boosthit811

4 жыл бұрын

It just un clips man.

hey i lost that sealing rubber, any idea where i can find it? i cant drive my car because of this stupid rubber

@boosthit811

Жыл бұрын

If its not inside still have to go to a junkyard and get one. Many cars use the same style joint.

@AntonisTsik

Жыл бұрын

Thanks mate

My clutch leaks i have a peugeot 407 1.6 hdi should i change this??

@boosthit811

3 жыл бұрын

You will need to investigate where its leaking from first......

@mevlandedja2457

3 жыл бұрын

@@boosthit811 it there where a tube presses inside the trasmission changes the gears

@mevlandedja2457

3 жыл бұрын

Is like 20 cm from the driven side wheel

@boosthit811

3 жыл бұрын

Sounds like you need to get to a workshop.

Where can I buy that rubber seal?

@boosthit811

6 ай бұрын

It comes with the bearing kit

@raymundbiagtan6544

6 ай бұрын

Can you send me the link where I can buy it? Thank you so much

Hi I have a 2010 ford galaxy and clutch fluied coming out in btwen gear box and engine not hard just slow drips

@americoalmada7316

4 жыл бұрын

Been told slave celinder

@boosthit811

4 жыл бұрын

@@americoalmada7316 oh yep. Have you seen the leak? Its quiet obvious if you get someone to pump the clutch while checking over with torch. If not the joint then only other place can be slave seal....

@americoalmada7316

4 жыл бұрын

@@boosthit811 yes I had someone pumping and I was under the car and loads of fluid poors out bout went out yesterday and no oil leaks

@boosthit811

4 жыл бұрын

@@americoalmada7316 oh well. Time for a clutch kit and new slave cylinder!

@americoalmada7316

4 жыл бұрын

@@boosthit811 just took car for a drive and nothing wrong hmm

So how do you bleed it

@boosthit811

11 ай бұрын

Use a vacuum brake bleeder

Yep, bitten me today!