Chrysler Witech 2.0 Overview and Tips
Автокөліктер мен көлік құралдары
This video was produced for the Trained By Techs channel!
I give a brief walkthrough, and cover a few hidden gems in the Witech 2.0, which is Chrysler's current diagnostic software.
Weekly Training Available at www.Patreon.com/KeithPerkins
Check Out My Amazon Store HERE:
tinyurl.com/yc8d99vf
Some other tools I use:
Launch Diagun IV X431
amzn.to/2SVxG27
Autel Elite
amzn.to/2MfabON
SDT-206 Smoke Machine Kit
amzn.to/2FyLQm1
Redline Smoke Fluid
amzn.to/2MbfKhv
PicoScope 4 Channel Kit
amzn.to/2Mfcy49
Hantek CC-65 Low Amp Clamp
amzn.to/2T4w9Xm
Hantek CC-650 High Amp Clamp
amzn.to/2RVgGeW
AESWave Uscope
amzn.to/2Fw4Fqx
VVDI Key Tool
amzn.to/2SXa4Ky
FLIR ONE Thermal Imager
amzn.to/2MbcjHo
Streamlight ProTac 2L-X
amzn.to/2VVq0yH
EBL 18650 Batteries
amzn.to/2Mbi6gj
Immobilizer Coil LED Tester
amzn.to/2SXHad0
Launch Creader3001 Code Reader
amzn.to/2ROlIdk
Пікірлер: 52
Great video. I'm a new technician at a Chrysler dodge jeep ram dealership so still learning the witech system. Good reference if I need it
Great video Keith, thanks for sharing 👍
Awesome presentation I'm working also here in the dealer using the same device.thanks for sharing.
Great video keep them coming
Awesome video Keith!
@L1Training
6 жыл бұрын
Thank you very much! This means a lot coming from you!
Hello, great video! We have a chrysler car workshop and my brother offered me a programmer job there. So how do I start learning how to use the witech program?
do you have a FCA video on the importance of VSRs and where to find the documentation on which claims - LOPs will need A vehicle Scan Report Would be real usefull. Thanks
Hi, is that possible to re config in the BCM the park lights of a Jeep Cherokee KL that has the park lights as a German standard (one side or the other with the turn lights commutator) to change that both sides light att the same time? Thank you.
Can you use a apple tab to run witech 2.0 with the micro pod?
Question, under a bcm report do you know what sw-year and hw-year mean?
Will this work on a 2000 ram 1500 5.9 magnum to fuel sync ty
really good video, i changed abs module on 2010 wrangler, could i reflash pcm to vin match with micropod or must be with j2534 passthrough?
Can you advise me, can I make ecu ignore some sensors using witech? I need to prepare vehicle for expedition and need reliability, thanks.
where can i buy this. the lings dont have the one on the video
Hey, great video! One question regarding light settings with WiTech. Is it possible to change it with this program? For instance DRL on in combination with the low beams?
@L1Training
Жыл бұрын
No.
I am getting wytec really soon here so on the new 2.0 I can use my tablet wireless???
@L1Training
5 жыл бұрын
Yes
Hy, i have a question. Just purchased a durango and added a trailer hitch to it, come to find out a dealer has to activate the electrical part of it. Not paying a dealer one hour labor for that job, so i went and got me a micropod2. I find the ecu configuration and see all values but how can i change them?? Thank you
@L1Training
5 жыл бұрын
Your clone chinese micropod will do you no good. You must call the dealer and ask them to add that option to your VIN, then use a active micropod logged into a active witech account and perform a configuration resrore on the module. Then it will function.
@martink.4659
5 жыл бұрын
Thank you!
PCM vin can change easily with any tool can i change ABS vin ?? And also there is configuration differences code in ABS can i also do configuration??
@L1Training
4 ай бұрын
Banana nut bread has nuts..... sorry thought we were bringing up stuff that has no relation to the video... my bad. Yes it does configurations, its the OEM tool.
If I'm using a CarDaq that's already approved by witech 2.0 for aftermarket will the online witech work? Or is the online witech strictly only for the micropod? Need to work on 2018+ vehicles that have the SGM. Thanks
@L1Training
5 жыл бұрын
Yes it will work for online WiTECH2 J2534
@joedefreitas4490
4 жыл бұрын
To piggyback on this comment, with witech can you gain bidirectional controls without removing the SGM?
@L1Training
4 жыл бұрын
In order to access bidirectional control or any function other than reading codes on a 2018+ SGM with witech will require an additional techauthority subscription.
@joedefreitas4490
4 жыл бұрын
Shoot that beats the heck out of searching and removing those goofy things! Thank you for your response and taking the time to put out these videos! 👍
@philh9238
4 жыл бұрын
I just sent the approval to Chrysler today for my cardaq now waiting for the 2 days to get approved. Have you used your cardaq to flash anything on witech 2.0 if so how is it working
Can a used skreem module be used on a 2006 Jeep Grand Cherokee Limited??
@96LS1S10
3 жыл бұрын
No.
Is it possible to change configuration? For example delete rear O2 sensors?
@96LS1S10
3 жыл бұрын
No. That is tuning software. This is diagnostic software.
@StanleyOrloff
3 жыл бұрын
@@96LS1S10 Which tuning software can do that?
Does willtech 2 will work on Jeep Grand Cherokee 3.6 2018?
@L1Training
3 жыл бұрын
Yes, it is the factory tool for ALL 2008 and up FCA products.
Does the wiTech work on 2016 cars ?
@L1Training
5 жыл бұрын
Yes, it is the most current tool used in the dealer, it covers 2010ish up to current. There is a chart on the Chrysler site showing which tool, covers which models.
@96LS1S10
3 жыл бұрын
Witech is used in cars 2006-current. SOME 2005's.
can i do proxy aligment for jeep cherokee kl 2018 ?
@L1Training
2 жыл бұрын
Yep.
Does the pasthru devices support this sw?
@L1Training
2 жыл бұрын
Yes, this software does support many different pass thru devices. But not all.
@viridian6903
2 жыл бұрын
@@L1Training does the vax nano gm can be used as passthro device for reflash
Hey my please tell me if I canor where I can buy this tool
@L1Training
3 жыл бұрын
submgr.am.fcawitech.com/login.htm
@rodger6940
3 жыл бұрын
Can you please advise me if this tool is good to buy it Chrysler Diagnostic Tool wiTech MicroPod 2 V17.04.17 With DELL D630 or Lenovo T420 I found it on line
@L1Training
3 жыл бұрын
If you are not buying from the OEM it is pirated or hacked software.
@rodger6940
3 жыл бұрын
So you think it wont work I'm having the code p167a mismatch and I want to buy the tool to reflash the transmission or update the software if it needs it. I work on cars but I'm not a professional I have learn a lot from a lot of mechanics here in KZread thanks for your time and help bro
@rodger6940
3 жыл бұрын
How much is the tool or how much did you pay for it?