Really appreciate the detail you provide especially with the plastic grommets and gaskets on the Chevrolet truck series. These plastic pieces and parts cost me more grief than you could possibly imagine you've provided some decent workarounds and insight thank you

the best video . Watch 2x looking forward to replace gmc yukon this July 4th weekend. Thanks best video.

Just want you say thank you! Changed mine out with my friend folling your video!

Getting the damn straps lined up putting it back in is the hardest part from the floor. Good video.

Outstanding video. You really took your time with the camera angle and explained everything thoroughly. And you didn't cuss or throw tools (as I would've). Subscribed!

@BLUECOLLARGARAGE

8 ай бұрын

Thanks for watching. We appreciate your support!

Very helpful without a rack, you saved me.

one of the best video i watch to do my yukon i thank you alot for all the details

Man, that's a heck of a long, somewhat tedious job! Wish I had the knowledge, equipment and space for doing my own repairs. Repair costs, parts and labor, are getting absolutely ridiculous these days. Great vid... thanks!

Nice job! Very detailed.

Two cinder blocks one on each side of the vehicle with an 8' 2x4 allows you to easily lower and raise the tank with gas or without! Instead of fighting with the evap lines on the back remove the evap canisters two 13mm bolts and lower the evap canister with the tank!

@BLUECOLLARGARAGE

3 ай бұрын

Thanks for the tip.

Great Job, Much covered and camera covered angles.

Best video. I have to do this tomorrow.

great video/editing! thank you

Excellent video! We'll done !

Great video Thanks

Nice detailed video, did mine a little different as I couldn't get the second fuel line in the front of the tank disconnected(why did they put these connectors where you can't see or really reach them?? and tabs you can't disconnect with your fingers?? 😡) Disconnected the driveshaft for more room, dropped the back of the tank down and was able to disconnect the lines off the pump then popped the lines out from the tank. Dropped the tank all the way out, Installed an ACDelco premium pump(genuine GM replacement) made in China 🙄 Hopefully lasts as long as the original 160k mi. Took 4-6 hrs and could do it again in 3 but may just cut the floor next time if these pumps don't last long.

@BLUECOLLARGARAGE

4 ай бұрын

They don’t make it easy that’s for sure. GM pumps have always had issues and don’t last long I’m surprised they never put a hatch in all their vehicles for easier access.

HOW THE PUMP PERFORMANCE SO FAR? GETTING ONE TOMORROW...MINE IS LEAKING AND LOOSING POWER GOING UPHILL.

@BLUECOLLARGARAGE

2 ай бұрын

Still going strong no issues.

what's the difference from a gas and flex pumps?

@BLUECOLLARGARAGE

7 ай бұрын

The only difference is on the fuel pump the normal regular gas will have three lines coming off of it where as the flex fuel only has two lines coming off the fuel pump.

I broke one of my evaporator plastic lines? How screwed am I?

@BLUECOLLARGARAGE

Ай бұрын

You may get a check engine light but it most likely won’t effect the way it runs

@papergatorzfedducca7998

Ай бұрын

@@BLUECOLLARGARAGE ok thank you bro!!

How much would you charge someone for that work ?

@BLUECOLLARGARAGE

Жыл бұрын

Labor I’d say about $150-$250.

@thespeedjunkieo2904

11 ай бұрын

My mechanic told me 850 to do smh

@gmarmaduraexotics

6 ай бұрын

that's what the charge fee is. take les then 2 hrs at a shop@@thespeedjunkieo2904

Cant you drop the tank down some so you have more room

@BLUECOLLARGARAGE

4 ай бұрын

You can just be careful with the evap lines.

Is that a flex fuel pump?

@BLUECOLLARGARAGE

2 ай бұрын

Yep

Great video mane

Badass bro. Thank you for the help. How has it been holding up?

@BLUECOLLARGARAGE

2 ай бұрын

So far so good this was done on a buddy’s and he’s still driving it everywhere.

@orion000

2 ай бұрын

Best gmt800 video on fuel pump replacement. God bless you Sir, take care

Looks like imma have to give this a shot. 🫡 Cars acting up. Appreciate the detailed guide

@LS3D_Printing

Жыл бұрын

Absolutely amazing. Got the car up and running. The hardest part was taking off the clip on the fuel pump and lifting it back into the car. Besides that super easy. Thank you dude.