CHANGING VALVE GUIDE SEALS WITHOUT REMOVING THE HEADS
In this video I demonstrate a way to remove valve springs without removing the heads from the block.
Жүктеу.....
Пікірлер: 39
@samstrolia7 күн бұрын
You're a crafty fella. Thanks for the ideas on this! My 89 Vettes got some seals that are going. ARG.
@markhubanks371510 ай бұрын
You video was very straightforward with no distractions. I'm getting ready to do my small block Chevy and can use your instructions. Thank You!
@wild13hawk Жыл бұрын
Awesome valve spring compressor idea!
@rinserepeat28779 ай бұрын
Excellent tool mode on the wrench!! Great job over all. Appreciate/subscribed!!
@randywl8925 Жыл бұрын
It's strange how hard the person has to look for information like this. What I see done differently everywhere, and what I've been told everywhere, makes this job confusing. I've been told if it's leaking it needs new valve guides. I've been told to only use the O-rings. I've been told to use the O-rings and an umbrella seal but only on the intake side because the exhaust heat will destroy the umbrella seal. I've been told that if you use both seals, it won't get enough oil to lubricate the valve stem. I've also been told to just using the umbrella. I've been told to get Viton seals, did I heard pros and cons for different reasons. ......ah crap, ill just buy a new engine and be done with it. 😁 Thanks for the video 👍
@cdoublejj
6 ай бұрын
Part of why it's called an art. If you were a real hot rodder you'd know you can only drink certain brands of beer when doing the job and only certain kinds of BBQ chicken for lunch! for real though i depends on the engine and context and use case. in the case of my astro van aside from factory "updates" and a hotrod radiator it's all stock. if the guides are worn i'm sure new seals will help so far but, it well enough before, it's preventative maint for a vehicle from 2001, rubber doesn't last forever.
@adamredden20079 ай бұрын
Man I love youtube. Thanks man
@jasonbaill704811 ай бұрын
hey, thanks looks like someting I can accomplish, many thanks J. 😃
@alfredwotlolan2168 Жыл бұрын
Excellent. Thank u Sir
@byker4lyfe13 ай бұрын
Cool idea bud. Some helpful tips... maybe, valve spring compressor tool 2.0 don't cut the end off the wrench just bend it. Tip 2 use a length of old spark plug wire in the spark plug hole push it in till it stops coiling oh make sure the piston is at TDC compression. Way faster and safer and no need for an air compressor 😊 but I like what you did here great video
@jasonbaill704811 ай бұрын
hey thanks, got to do this, mine ( 305 ,5.0 sbc ) smoking a lot , try this first don" want to pull or replace the engine retired got to save $$$. many thanks. J.
@guillermonieri42032 ай бұрын
Thank you.
@BrianYoder-tk9kj11 ай бұрын
Great question.. how many psi are you runni g? I need to do this on my roadrunner..
@philliphall5198 Жыл бұрын
Done a lot this way on 283,327&350 engines back in the day I used a oil burner adapter and braze fitting in it and air hose
@chasedavis2358Ай бұрын
Can you put each cylinder to tdc and use the piston to hold the valves up?
@MariamMelodies6 ай бұрын
quarter inch or three eights nylon cord works also. just pack it into your cylinder head and leave some sticking out to pull when finished
@yewallreadyknow88097 ай бұрын
BG Auto What psi is your air compressor set at?
@brianb66533 ай бұрын
I might be underthinking it.... but why did you fight with the o-ring AFTER putting the spring back in place? I don't see anything that would prevent you from putting that o-ring where it needs to be in the first place and then setting the spring on top of it and compressing/installing keepers. Something i'm missing ?
@gregorydavid77557 ай бұрын
May be a dumb question to some but why dont u put the O Ring on before u drop the Spring back on ?
@therealblakekirkham5701
4 ай бұрын
Wild guess but So you don't nick the seal with the retainer as your synching it down
@cdoublejj6 ай бұрын
mine have metal base that looks like it squeezes the outer casing of the guide
@robertcampbell548510 ай бұрын
fucking brilliant
@wayneturner7678 Жыл бұрын
how did you lock off the valves to top them moving
@loganedwards7158
Жыл бұрын
You can take a compression tester tool and fit an air compressor to the quick connect nipple and pressurize the cylinder with air. That’s what he did basically.
@CoroPlanesLLC
Жыл бұрын
That's what the air hose to spark plug adapter is for. You put compressed air into the cylinder you are working on, and the air keeps the valve closed while you do your work.
@Bajjaad
Жыл бұрын
recenty got changed by liana's valve seal by holding valve with rope method....in air pressure scene you need to hold engine permanently to void engine turning as there will be cinstant air pressure on piston while in rope method you will be more easy with execution ... you must find a video with rope method on you tube ... it is easy
@wellscody863 ай бұрын
Usually the umbrella seals are for the exhaust- the rubber with the clamp ring are for intakes- hope you didn’t just get them swapped.
@natep99975 ай бұрын
Will this work with a 2013 hyundai sonata? They replaced the motor at 153k and its at 171k and the valve guide seals are bad. Smokes like a bitch on almost every start
@tony8570Ай бұрын
Put a drill on the valve. Spin it a few times to clean up the valve seat. Not much, just enough to get the job done.
@ilyeschaouaou9734
21 күн бұрын
Will try . Im tryng to change my seals for the first time
@JayDJones-hb1wh11 ай бұрын
How many PSI on the compressor?
@coast.cutter7552
11 ай бұрын
150
@ELlos2106 ай бұрын
Can you use a small 3 gallon compressor?
@therealblakekirkham5701
4 ай бұрын
Yes I've done it with a pancake
@ELlos210
4 ай бұрын
@@therealblakekirkham5701 badass. Thanks for the info
@obiirosa66552 ай бұрын
Why not just use a cyl leakdown test tool to pressurize the cyl?
@jamesjohnson6366
20 күн бұрын
Bc if it does have a leak then it would drop the valves. Would also have to turn engine over to build pressure again. With the compressor set up, he should hold a constant pressure regardless if it was leaking or not
@salnichols9480510 ай бұрын
So, for like $20.00 you can buy a valve spring compressor…
Пікірлер: 39
You're a crafty fella. Thanks for the ideas on this! My 89 Vettes got some seals that are going. ARG.
You video was very straightforward with no distractions. I'm getting ready to do my small block Chevy and can use your instructions. Thank You!
Awesome valve spring compressor idea!
Excellent tool mode on the wrench!! Great job over all. Appreciate/subscribed!!
It's strange how hard the person has to look for information like this. What I see done differently everywhere, and what I've been told everywhere, makes this job confusing. I've been told if it's leaking it needs new valve guides. I've been told to only use the O-rings. I've been told to use the O-rings and an umbrella seal but only on the intake side because the exhaust heat will destroy the umbrella seal. I've been told that if you use both seals, it won't get enough oil to lubricate the valve stem. I've also been told to just using the umbrella. I've been told to get Viton seals, did I heard pros and cons for different reasons. ......ah crap, ill just buy a new engine and be done with it. 😁 Thanks for the video 👍
@cdoublejj
6 ай бұрын
Part of why it's called an art. If you were a real hot rodder you'd know you can only drink certain brands of beer when doing the job and only certain kinds of BBQ chicken for lunch! for real though i depends on the engine and context and use case. in the case of my astro van aside from factory "updates" and a hotrod radiator it's all stock. if the guides are worn i'm sure new seals will help so far but, it well enough before, it's preventative maint for a vehicle from 2001, rubber doesn't last forever.
Man I love youtube. Thanks man
hey, thanks looks like someting I can accomplish, many thanks J. 😃
Excellent. Thank u Sir
Cool idea bud. Some helpful tips... maybe, valve spring compressor tool 2.0 don't cut the end off the wrench just bend it. Tip 2 use a length of old spark plug wire in the spark plug hole push it in till it stops coiling oh make sure the piston is at TDC compression. Way faster and safer and no need for an air compressor 😊 but I like what you did here great video
hey thanks, got to do this, mine ( 305 ,5.0 sbc ) smoking a lot , try this first don" want to pull or replace the engine retired got to save $$$. many thanks. J.
Thank you.
Great question.. how many psi are you runni g? I need to do this on my roadrunner..
Done a lot this way on 283,327&350 engines back in the day I used a oil burner adapter and braze fitting in it and air hose
Can you put each cylinder to tdc and use the piston to hold the valves up?
quarter inch or three eights nylon cord works also. just pack it into your cylinder head and leave some sticking out to pull when finished
BG Auto What psi is your air compressor set at?
I might be underthinking it.... but why did you fight with the o-ring AFTER putting the spring back in place? I don't see anything that would prevent you from putting that o-ring where it needs to be in the first place and then setting the spring on top of it and compressing/installing keepers. Something i'm missing ?
May be a dumb question to some but why dont u put the O Ring on before u drop the Spring back on ?
@therealblakekirkham5701
4 ай бұрын
Wild guess but So you don't nick the seal with the retainer as your synching it down
mine have metal base that looks like it squeezes the outer casing of the guide
fucking brilliant
how did you lock off the valves to top them moving
@loganedwards7158
Жыл бұрын
You can take a compression tester tool and fit an air compressor to the quick connect nipple and pressurize the cylinder with air. That’s what he did basically.
@CoroPlanesLLC
Жыл бұрын
That's what the air hose to spark plug adapter is for. You put compressed air into the cylinder you are working on, and the air keeps the valve closed while you do your work.
@Bajjaad
Жыл бұрын
recenty got changed by liana's valve seal by holding valve with rope method....in air pressure scene you need to hold engine permanently to void engine turning as there will be cinstant air pressure on piston while in rope method you will be more easy with execution ... you must find a video with rope method on you tube ... it is easy
Usually the umbrella seals are for the exhaust- the rubber with the clamp ring are for intakes- hope you didn’t just get them swapped.
Will this work with a 2013 hyundai sonata? They replaced the motor at 153k and its at 171k and the valve guide seals are bad. Smokes like a bitch on almost every start
Put a drill on the valve. Spin it a few times to clean up the valve seat. Not much, just enough to get the job done.
@ilyeschaouaou9734
21 күн бұрын
Will try . Im tryng to change my seals for the first time
How many PSI on the compressor?
@coast.cutter7552
11 ай бұрын
150
Can you use a small 3 gallon compressor?
@therealblakekirkham5701
4 ай бұрын
Yes I've done it with a pancake
@ELlos210
4 ай бұрын
@@therealblakekirkham5701 badass. Thanks for the info
Why not just use a cyl leakdown test tool to pressurize the cyl?
@jamesjohnson6366
20 күн бұрын
Bc if it does have a leak then it would drop the valves. Would also have to turn engine over to build pressure again. With the compressor set up, he should hold a constant pressure regardless if it was leaking or not
So, for like $20.00 you can buy a valve spring compressor…
@victorparra4227
9 ай бұрын
The cheap ones suck