Thanks for all that you do! Keep doing them!

you are good instructor i learned a lot from you thanks my friend.

nice one again sir Jhun thank you for sharing with us, always take care and God bless

Thanks a lot ... Nice and very helpfull video....

Thank you very much helps me a lat.

Thank you sir being good and sharing God bless poh

Thanks for sharing bro

Thanks this video hepled me a lot, keep it up 🖤

@caterpillarjhunhunk

2 жыл бұрын

thanks bro

nice good work 🙏

Had exactly that problem. Motor stall (bog down) when doing digging (with moderate force required) or any cylinder was at the end of travel and I kept pumping oil by holding lever in position. This way with stick and boom cylinder engine quit within seconds and for bucket cylinder it took a tiny bit longer. My excavator has also the "attachment" valve as you show at the end of your video. I took the "attachment solenoid (I currently don't use) and put it in place of the power shift solenoid and excavator work perfect now. (ordered new part on amazon)

@caterpillarjhunhunk

10 ай бұрын

If any hesitation or confuse, contac me in my whatsapp,+971567581176 for fast conversation

Thank you for clarifying my power power shift problem on a 330 D MH. U simplified it nd we have a few issue like this in our fleet. Thank you agian

@caterpillarjhunhunk

5 ай бұрын

contac me in whatsapp +971567581176

Very nice video and information thanx for you

@caterpillarjhunhunk

Жыл бұрын

welcome bro

شكرا لك

Thank you sir for your tips.thats my problem this time and I'll do. It tomorrow.

@caterpillarjhunhunk

Жыл бұрын

thanks more for your support

Great video 👍

@caterpillarjhunhunk

2 жыл бұрын

thanks bro

Nice work sir.👍🏻

@caterpillarjhunhunk

2 жыл бұрын

thanks bro

Salamat sa sharing boss Godbless

@caterpillarjhunhunk

3 жыл бұрын

welcome sini share ko lang nman ang mga natututnan pra s mga baguhan atlist d man complete matutunan sila s video ko, salamat din s support

تحياتي لك من المغرب

@caterpillarjhunhunk

2 жыл бұрын

shokran

thank you very much mr jhun

@caterpillarjhunhunk

Жыл бұрын

welcome bos

Nice sir more power❤❤❤

@caterpillarjhunhunk

10 ай бұрын

thank you

Thank you so much

@caterpillarjhunhunk

10 ай бұрын

your welcome bro

Thank you for your explanation,,I have problem with my 325dl caterpillar excavator,loose power when it is working..

@caterpillarjhunhunk

4 ай бұрын

You have to make sure what is the main cause of low power

Please kindly teach me how to calibrate it in case I have any issue about it

Make more video about hydraulic system,tq

@caterpillarjhunhunk

Жыл бұрын

ok bro we will,try to do more videos

How to troubleshoot the current supply of the 320 caterpillar for the hydrolic lolck soliniod when I down lever control handle no current well reach to the bottom of sacket help jun

@caterpillarjhunhunk

6 ай бұрын

On down position of the hydraulic lock dis ingage, meaning cutoff power or neutral, can you contac me in my whatsapp +971567581176 to know more about the trouble and some other details of the problem

Thankyou

@caterpillarjhunhunk

Ай бұрын

Welcome bro

Pak mau nanya mesin caterpillar 3216 sistem HEUI tidak mau runing . Tetapi saat di pancing bensin dia baru mau running . Mohon sarannya pengecekanbta pak ... terima kasih ...

In my Cat330C , there is an alarm beep, and on the screen "low oil pressure appears" every time when it beeps. When I change the engine oil, the alarm doesn't beep for few days or beep just a little. But after like 15 days it starts beeping sometimes for an hour. While it beeps the machine works slow. This alarm issue is from a long time. I don't understand, if the sensor has some problem or the oil is too thick.

@caterpillarjhunhunk

2 жыл бұрын

bro you have to check on the monitoring system to make it sure witch type of error shows on the monitor, on that way we can deside for what to, ok check it first error then tell me

@hanifkhan3465

2 жыл бұрын

It appears as " Eng oil press low". Last few days the alarm did beep but for few mins in the whole day, sometimes twice a day and sometimes doesn't beep. I just changed the oil and filter yesterday in the evening. Today after half an hour working it started to beep again and it's been an hour now. Whenever it beeps the machine power becomes a little low. This alarm issue is from an year, if u have any idea how to solve it, kindly let me know.

@stevejones6349

2 жыл бұрын

@@hanifkhan3465 Check the oil pressure with a gauge. If the pressure is good replace the oil pressure sensor. If it's bad your bearings or oil pump may be worn out. But if it has run for twelve months without throwing a conrod through the block then my bet would be on the sensor

Hi have problem with cat 311uc low power on slew motor and one left side trac and bogs down when lowering boom can you help ?

@caterpillarjhunhunk

2 жыл бұрын

bro sorry but i cannot understand what you mean about your problem, contac me in my whatsapp +971567581176 for better conversation and i need more details about your machine about photo and serial no. ok

Thank you sir . I have a problem with my 320D all the hydraulics are slow, travel , boom and swing . Is it normal for the power shift pressure to be constant at 3550[kpa] on idle and when operating at the speed of 10 does not change? Your assistance will be a massive help.

@caterpillarjhunhunk

Жыл бұрын

if we are talking power shift the power shift will change in pull rpm to lower pressure, then will be coming more lower while you are operating the machine

We have a 1994 320 Cat Excavator and we just put in a new hydraulic pump and the machine ran really well for about 5 hours then all of a sudden the joystick controls did not work the machine was running full power but nothing was moving (the boom, travel, etc.) Does that have anyting to do with the solenoid?

@caterpillarjhunhunk

Жыл бұрын

yes bro check the hydraulic lock solenoid maybe it is not opening or the solenoid is damage.inspect the electrical wiring and the solenoid

Please I have cat machine 323DL and I wanted you to show me how to calibrate it

@caterpillarjhunhunk

2 жыл бұрын

brother can you pls kindly spicify which part of machine would you like to calibrate

hello sir jhun,tanong ko lang po kung ilang volts meron dapat ang power shift solenoids ? sano po masagot nyo po tanong ko na eto,maraming salamat po sa inyo,!!!,more power!!

What is the cause of back and forth slow movement of excavator 330 bL

@caterpillarjhunhunk

2 жыл бұрын

the main reason is low pressure,many reason why because of the machine long time using for work. so before you start do the trouble shooting you have to investigate how the trouble started

How to adjustment pumps pressure ..? make A video about all adjustment ON THe hydraulic pump plz sir..🤲

@caterpillarjhunhunk

2 жыл бұрын

i have some video regarding about adjusment of main pump maybe you can get idea from that video

Watching from cebu,.. salamat sir sa inyung binahaging kaalaman,.sir baka pwd maka hingi ng mga error code ng CAT para mapag-aralan ko.. Gob bless 🙏

@caterpillarjhunhunk

3 жыл бұрын

may whatsapp kb +971567581176 message mo ako

@phoolkhan2282

3 жыл бұрын

@@caterpillarjhunhunk assalamo alaikum sir have cat320D excavator low power &sutdown machine and active code are 36-190-8 &39- 167-12 sir what is problem pls reply

@caterpillarjhunhunk

3 жыл бұрын

@@phoolkhan2282 bro actualy that problem is not easy to identify where the problem, i have some step to do to find out what type of problem we have. but you can conrac me in my whatsapp mor better to talk. +971567581176

@caterpillarjhunhunk

3 жыл бұрын

@@phoolkhan2282 bro try to check 190 is a speed timing sensor located at fly wheel side ok maybe dmage or loose connection, and the other one is 167 alternator maybe the sensing wire for charging is disconnected or maybe damage check the charging on monitor if morethan 27v engine is running maybe the sensing wire damage or disconnected

Could you please help me thanks

hello sir when I remove shift pressure solenoid cable and move joystick the rpm of engine still up and down not dying and the power of all movement is slow what the reason ?

@caterpillarjhunhunk

6 ай бұрын

Bro contac me in my whatsapp +971544794515 i need more details about your machine, brand

Frend u Dan great but I need to ask you The password to make diagnosis.

@caterpillarjhunhunk

2 жыл бұрын

enter pasword FFF2

My friend...313bsr cat...no rpm during operation what's a problem.?

@caterpillarjhunhunk

8 ай бұрын

bro contac me in my whatsapp+971567581176

At minute 13.07, how do change the reading from kpa to psi, thanks for sharing.

@caterpillarjhunhunk

9 ай бұрын

Bro i dont know what type of machine you have, contac in my whatsapp +971567581176

Hello sir how are you?? I have a problem with a volve excavator is there any way I can contact you?

@caterpillarjhunhunk

Ай бұрын

You can contac me in my whatsapp +971567581176

Very good information, and what mean error 95-168 -5 , and what this to do solves it??? And thank's to help

@caterpillarjhunhunk

3 жыл бұрын

which machine you have

@sapri6328

3 жыл бұрын

Cat320D

@caterpillarjhunhunk

3 жыл бұрын

@@sapri6328 ok bro 1 by 1 first 95 is fuel deffirential pressure sensor maybe broken wire or sensor damage located at the fuel filter that is rectangular form with four bolts and three wires, 168 electrical system you have to do inspection to the wires beside the engine ok same open connection

@sapri6328

3 жыл бұрын

Ok thank's very much, en God bles👍🏻👍🏻👍🏻🙏🙏🙏

@caterpillarjhunhunk

3 жыл бұрын

@@sapri6328 bro like share and subscribe

I have cat cat 311uc seems to be the same problem ,there is no monitor to display the codes how would i get these codes?

@caterpillarjhunhunk

Жыл бұрын

bro can contac me in my whatsapp +971567581176,send me some. picture what type mo monitor we have on your machine, and also serial number

Hi thanks for video, i am facing one problem in caterpillar excavator 320D, IMPL PWR Shift Presser not increasing solenoid is we are replaced done, up solenoid voltage is coming plz. advice

@caterpillarjhunhunk

3 жыл бұрын

i'm i cannot understand what do mean, contac me in my whatsapp, +971567581176 for better conversation ok

@louiduruin760

2 жыл бұрын

Ser im having problem with my komatsu...it can move all its moving parts...after using a couple of hours ...limit 1 hour after that then the machine wont mive anymore ...any advice please.... Its a komatsu wheel type excavator

What is problem is mashine working with power shift disconnected?

@caterpillarjhunhunk

3 жыл бұрын

actualy bro on my video if the power shift solenoid is no supply or not functioning the engine is overload or it will coming shutdown if you forcely work

Sir how about my 325cat only 900rpm what is the trouble.

@caterpillarjhunhunk

Жыл бұрын

Bro i dont know you never share it to me whats is the exact problem this is my whatsapp +971567581176

Sir Caterpillar c9 engine run on 1800 rpm and then slowly slowly with in 3 to 4 minutes engine come to 800 rpm... please tell me the fault

@caterpillarjhunhunk

2 жыл бұрын

at first you should have to check the possible active error,maybe on that error is the main cause of problem,or try to check the fuel line if the engine is slowly slowly low raise,but i dont exactly what happen to your machine this just my analysis base on what you told me.

I have 36: 268-2 and 39: 171-4 pls guide

Sir gud day sir i have a question for our caterpilar 320d excavator my question is we replace a new used engine but the problem is when we start the engine it starts but after a few seconds it shut down do you think sir theres a problem in our ecu?

@caterpillarjhunhunk

Жыл бұрын

sorry sir for late response, regarding about your problem, so many reason why the engine is suddenly shutdown, in electrical related problem its possible on the common rail sensor intermitent functioning, or pressure fuel pump solenoid valve, and one more thing if you can see the speed sensor attached on flywheel there 2 different sensor is there 1 is treaded type and the other 1 is plastic type black color, this plastic type if the pulse is not accurate for the ecm requirement they can possibly shutdown the engine there is 1 more black plastic sensor at the lower side of fuel pump near engine black, that is same part # flywheel and pump, check bought sensor by multimeter check the difference.

@caterpillarjhunhunk

Жыл бұрын

there is one more idea, open the diagnostic onthe monitor then start if the engine is started live the monitor open at diagnostic then wait until the engine shutdown then see what other more error shows on monitor, or contact me in my whatsapp, +971567581176, for fastes conversation, ok then send me some video or picture for my refference to analys the problem

@jun2nepomuceno810

11 ай бұрын

Sir pwedi pahingi diagram sa switch na basag kc..manual at auto 12pins kc.hirap i sa ayus baka ma baliktad

Sir ask ko lang po CAT320d... namamatay makina kapag nagbboom up, lalo na kapag may load un bucket

@caterpillarjhunhunk

Жыл бұрын

ganito mag ptessure test muna kyo, tpos record nyo para kung sakali n mabago nyo o nagadjust kyo pwede nyo maibalik s dati kung mali, tapos check mo pressure ng power shift kung nagbbago b ang pressure nya kpag nagooperate ang machine, pag hindi ppweding may problema s power shift, kung ok power shift, mag adjust kyo or bawasan ang flow ng hydraulic, diba nsa magkabilang gilid ng pump may nkalagay n valve at may adjuster, ung adjuster doon kaliwa at kanan parehong may adjuster ang lock nut nya is 36mm luwagan nyo un, tapos pihitin nyo pabalik or same as paluwagisang ikot tpos testing kpag nagbago sya at bumagal, tpos hindi n nmamatay, dahan dahan nman s pag higpit, dpat pareho un ha wag isa lang, at gumamiti kyo ng thermometer para malaman nyo in 30mins n test kung alin pump ang may high temp, un ang bbawasan ang flow hanggang maging ok ang Machine dapat balance temp nya

Hellow kabayan patulong Naman nagagawa Ako Ng cat. 320d crank only walang curente sa injictor.. alin kaya Ang puidi ko palitan sir or ichik.... tenx sa reply

@caterpillarjhunhunk

9 ай бұрын

Sir sinsya na late reponse, check nyo muna power supply ng ecm mo baka kulang ang supply n pumasok doon talagang hindi magkakapower yan, then baka hindi naglalabas ng high pressure ung fuel pump isa rin sa dahilan yan

what inlet air temp high

@caterpillarjhunhunk

4 ай бұрын

that sometimes happening if sensor damage or wiring damage, or maybe air intake temp. is getting high that some possibility

I'm also working in oman 6 years i have a Catar pilar adapted

@caterpillarjhunhunk

3 жыл бұрын

ok darling 00971567581176

@mdmahin-jn5sc

3 жыл бұрын

Thank u sir

Sir paki explane nmn bakit nanag memerge ang excavator na kumatsu para saan poba ang merge divider

@caterpillarjhunhunk

2 жыл бұрын

wait mo lang ha ggawa ako

Good morning i experience cat 320d error code show 39-167-12 what does it means?

@caterpillarjhunhunk

2 жыл бұрын

bro regarding about that error, 167 that is alternator charging sensor its either alternator regulator problem or harnes you can check that in the monitoring if the alternator is charging or not, the normal charging is 26v up to max 28v if the volts output is in between, that means its charging maybe the problem is in the sensing output from alternator, so now the alternator back side is 4 wires #1 is battery, #2 ground,# 3 single wire socket type that is the sensing wire maybe disconneted or shorted inside or harnes damage, #4 is a socket with 2 wires that is batt indicator and supply from ignation switch.or you can contac me in my whatsapp +971567581176 for fast conversation

Sir good morning 320dl anu po b dahilan ng power shift kapag ngstop s pressure 3550 ay low power n sya almost 3y n problema po ng excavator nmen patulong nman sir if my idea po kayo. Slamat

@caterpillarjhunhunk

4 ай бұрын

Kung ang power shift nya ay nka kabit p, may adjusment yan, screw type luwagan mo lang ung lock nut then adjust mo and observe

Sir pa help nmn bat mga kumatsu pc220-8 overhate hydrulic ano una galawin

@caterpillarjhunhunk

2 жыл бұрын

preventive maintenance muna bro bka ksi ung langis mo bumaba n ang viscosity nya dahilan bakit nagooverheat ventilation nya bka may mga obstraction, check mo filter ng hydraulic ung nsa loob ng tanke nya at ung cooling system nya ganun ung sensors baka harnes nya eh damage, kuntakin mo ako s whatsapp pra mas mabilis conversation natin

Can a solenoid be adjusted

@caterpillarjhunhunk

4 ай бұрын

if the solenoid type is available the adjustable screw possible but diffending what you need to do

Sir pano ba ayusun ung FUEL FILTER PLUGGED AT FUEL FILTER DERATE sana mapansin

@caterpillarjhunhunk

6 ай бұрын

Brad anung machine b yan, kpag fuel filter plugged kailan b last n nagpalit ng filter yan, may possibility n baradu n filte or ung fuel line mo kaya sya plugged

Sir tska po pala diagram ng connection ng back up switch condim napo mula pg dating samin surplus nbli ng boss ko gzto ko lagyan ng switch magbayad lng kmi sir.

@caterpillarjhunhunk

Жыл бұрын

hindi ko. alam kung anung machine ang tinutukoy mo.

Sir tnx for sharing ,,,sir how can I Contact you Privately?

@caterpillarjhunhunk

7 күн бұрын

You contac thru whatsapp +971567581176

@illuminadosanantoniojr.3022

5 күн бұрын

@@caterpillarjhunhunk sir I'm from the Philippines gusto ko po sana maka hingi ng info About Cat 312D excavator ang galaw po kasi mabagal pero ang performance po ng Engine ok naman po ang sa Hydraulics System nya ang may Problema ,lahat po ng Function ,,aside from Hyd. pump saan po kaya ang pwedeng panggalingan ng Problema tnx po nga pala ulit sana po matulungan nyo ako tnx po ulit

Hello sir what is the cause if the operator when he apply double engage the machine almost dying but he apply travel the machine is good as always the boom up and stick and bucket in and out only two motion like travel and boom up the machine is almost dying sir pls give the idea about this troubleshooting salamat poh sir

@caterpillarjhunhunk

2 жыл бұрын

usualy in that situation,you have check in full trigger for in and out or up and down,and what i mean is out for 10sec slowly until you reach full,observe that procedure then must be open the monitoring in pressure testing and observe how much pressure for each function in full trigger,or you can add me in what app for better conversation +971567581176

Sir jun pa add nmn po gilbert balbin... di ko kac magawa dozer

@caterpillarjhunhunk

Жыл бұрын

sige mo ako sa whatsapp +971567581176 mas accurate ang conbersation natin

What is a problem of cannot swing

@caterpillarjhunhunk

2 жыл бұрын

tell me witch machine you have, if komatsu try to check the switch and solenoid

Chef ...me prblem Sa gamit ko n pc 220 at 200.. mahina Ang steering ano Ang problem noon

@caterpillarjhunhunk

3 жыл бұрын

check pressure ng main pump pra malaman kung tama ba ang nlabas n pressure s mainpump bago magfollow next s trouble, shooting

Sir pwde po pa2long my unit kmi 320d umiinit po yng power shift solenoid hndi mahawakan posible kya ito sira tska low power galaw nya.

@caterpillarjhunhunk

Жыл бұрын

check mo ung power nya kung saan nagmula baka ksi nka direct n sya s power supply n 24v,ang normal nyan at galing sa ecm at dumaan ng mobility switch, nsa kanang side ng operator sit sa bandand likod ng upuan s kanan, kapag nakaon s mobility dapat makikita mo s monitor mobility at mawawalang ng supply ung power shift

@remartabang3997

Жыл бұрын

Good morning sir, naka direct nanga po sa 24 v yng supply ng power shift soleniod, sir bka po my diagram k ng connction ng switch yng sa kanang side sa likod wala napo kz switch myron po dn nkalagay pa yng sa hi in low ng speed nlng. Sir maraming salamat nareply mo aq.

how much ohm is the resistance of a working PRV solenoid sir?

@caterpillarjhunhunk

2 ай бұрын

Bro you dont mention what machine you have

@oipuniverse1030

2 ай бұрын

of course regarding this video about cat 20d sir@@caterpillarjhunhunk

@caterpillarjhunhunk

2 ай бұрын

@@oipuniverse1030 tell me what is the problem on prv maybe that is not the reason of problem

@oipuniverse1030

2 ай бұрын

boom rise and combination move very slow@@caterpillarjhunhunk

Boss pag na grawd ang backhoe ano po bang maaaring masira kc dati namang malakas bigla nalang humina backhoe namen

@caterpillarjhunhunk

8 ай бұрын

Paanung nag ground b o anung klasing pagkahina mausok b ang makina o namamatay ang makina

Hello sir jhun

@caterpillarjhunhunk

24 күн бұрын

Yes bos

Ano kaya problem sir, 515 psi lang reading nya sa monitor di nag nagbabago, dumadapa ang makina pag nag stall test, may supply 25 volts ang powershift solenoid, sa actual bar Guage ay 600 psi sya, nababa lang ng 540 psi pag nag tetesting, 5000 psi pump 1, possible ecm ba? Baka 25 volts lagi naka supply sa kanya, History, nagpalit ng injector anim saka machine harness,

@caterpillarjhunhunk

3 жыл бұрын

brad sinsya na ngayon ko lang nakita message mo ganito kung bagung calibrate ang injector ppweding hindi lahat nga injector e gumgana ng maayos pweding ganun, ppwede rin may isa s sensor nya n hindi nagffunction ng maayos kya nadapa ang andar ng makina, lalo n ung intake booster pressure sensor, maraming bisis n ako nka incounter ng ganyan, hindi sya nageerror pero d n nagffunction,normal lang yan supply ng power shift mo galing s ecm ang supply nyan then dumaan s switch n nsa loob ng cab s bandang kanan, kpag nkataas ung switch n un lalabas s monitor mobility nka low idle lang ang makina at kpag ginamit mo o pinagana mo mamamatay makina. inspection mo muna lahat ng nsabi ko ha. o kya kuntakin mo ako s whatsapp, +971567581176

For all of us.. we know what to do with a big black boom

Sir what are the 3 password in caterpilar

@caterpillarjhunhunk

2 жыл бұрын

the normal password of cat is FFF2, unless there someone change it

Boss anu kaya Sira cat317d2 ang alarm ay power train failure

@caterpillarjhunhunk

Жыл бұрын

sir sinsya s late response, ganito pwede mong gawin kung hindi nagagawa machine mo check mo maige ang error open mo service menu at s diagnose at active error then start mo then wait few second, or the best contakin mo ako s whatsapp +971567581176, mag send k ng pupwede kung way para ma maalaman ko kung saan nagmula problem

My swiych pi ba na gnyan sa exc.320d2 Sir?

@caterpillarjhunhunk

Жыл бұрын

aling switch b tinutokoy mo

@jaychristopherramireztabat8905

Жыл бұрын

@@caterpillarjhunhunk switch shifter po..

My machine power shift pres showing constant pressure 3550 no up and down after 5 min of running...and machine takes load

@shoaibkhattak8496

3 жыл бұрын

machine the pressure will be 3410 kpa and when we increase the mode will change into 2438 kpa and will vary according to the load. But when working after sometimes we feel the hydraulic pressure drop down and also engine is also not smooth sometimes can shut down the engine.On that time I noticed the power shift pressure remains constant at 3550 kpa.(in display).and physically by guage 520 psi. The voltage is getting 24 volt The machine operated in back up mode is the same as the hydraulic and engine operation is not smooth and some times it can shut down the engine ,when connecting the pressure guage can see it drops down to 220 psi. I would like to know whether this can happen due to injector/injector pump ,becuase all the machines have starting problem and using starting aid to start the engine

@caterpillarjhunhunk

3 жыл бұрын

@@shoaibkhattak8496 i dont know exactly where it came from about your problem, you know what, if your engine is electronic type or ecm type, and the engine suddenly shutdown while you are in testing my some sensor is not work or not functioning in normal or if the problem is in hydraulic system totaly everything will not fuctioning like normal, my advice you to check the engine by full close of arm or full up of boom

@shoaibkhattak8496

3 жыл бұрын

I dont know too much but its 2012 year

@shoaibkhattak8496

3 жыл бұрын

@@caterpillarjhunhunk full machine get slow all booms and chains is slow

@caterpillarjhunhunk

3 жыл бұрын

@@shoaibkhattak8496 i knew you can do it, you need to have other person to operate and you do checking actual of power shift the supply

Does 2000 RPM hurt your engine?

@caterpillarjhunhunk

2 жыл бұрын

thats depend on the standard setup of the manufacturer of the machine,but if you just setup by your self because of low power i think it is not adviseable,normaly 1900rpm its little different but your engine is protected in the sense of long life of the machine

@nitrekxd

2 жыл бұрын

@@caterpillarjhunhunk my Is a cat m316d and by fabric do 2000 RPM

@caterpillarjhunhunk

2 жыл бұрын

@@nitrekxd if you think thats is the normal live it

How problem hard starting caterpillar bako

@caterpillarjhunhunk

Жыл бұрын

pls contac in my whatsapp +971567581176 for easy and fast conversation

sir yung cat 321d ng boss ko humina ang galaw nya parang nag slow na anung problema kaya...

@caterpillarjhunhunk

3 жыл бұрын

brad check mo ung hydraulic pump pressure kung balance sya same. doon s video ko s youtube kung paanu e check or contac me s whatsapp +971567581176

@sigbin5018

3 жыл бұрын

@@caterpillarjhunhunk na check kuna parihas sa vedio na ginawa mo sir ok naman sya katulad ng sa vedio mo ang pressure tapus tiningnan kurin yung power ship nya mayron din pressure...ang ng yare daw bigla nalang humina ang backhoe wala naman error na nakita ko....

@sigbin5018

3 жыл бұрын

whatsapp...

magandang gabi sir, 318d ayaw mag high idle ano b sira nyn?

@caterpillarjhunhunk

2 жыл бұрын

may mga dahilan yan kung bakita ayaw gumana ang high idle ppweding sensor or low presure, katulad nlang ng speed output sensor or ung pedal sensor, the best nyan check mo error code logged at active, pero wla nag wwarning s monitor habang nka andar, at anung function ng machine ang hindi ng hhigh idle.or try mo s likod ng cab kung saan may mga solenoid, may dalawang pressure switch doon 2 wires lang sya ung isa s bandang loob at ung isa nsa bandang bukana, ang gawing mo full raise mo ung volume, ng accelerator then e short mo isa isa ung pressure switch

@elezarllaguno9156

2 жыл бұрын

@@caterpillarjhunhunk maraming salamat sir

@elezarllaguno9156

2 жыл бұрын

@@caterpillarjhunhunk 39-E00232=01, 39-E00265=02 loged event 39-1160=5 logged error ano pong sensor yan sir?

Sir pwedi pa hingi diagram sa swich sir 12pins sa caterpillar na basag kc hirap ikabit bka may masira iba

@caterpillarjhunhunk

11 ай бұрын

Ganito gawa k ng whatsapp +971567581176 contakin mo ako dito ha bigyan kita

@jun2nepomuceno810

11 ай бұрын

Pwedi massanger lang sir

Ser ayaw na gumalaw ng cat 320D ano kaya problema ayaw gumana nga safety lock release?

@caterpillarjhunhunk

Жыл бұрын

sir check muna kyo ng pressure, main pump, pilot pump, pati n rin power shift output

@zembertv4110

Жыл бұрын

@@caterpillarjhunhunk thank u ser....naayos narin po namin ...solenoid LNG pala ng safety lockout ang sira kaya operational na sya ngayon maraming slamat ser god bless to you and your channel sana marami kapa matutulungan...

330 dl limited mode signal and remote low

@caterpillarjhunhunk

Жыл бұрын

check the switch at the right side of sit at the back 2 switch is there 1is for limited mode put down direction all the switch knob ok

Anong problima sa scavator na ayaw lumalabas ang fuel anong gagawin po

@caterpillarjhunhunk

2 жыл бұрын

pogi bigyan mo naman ako idea kung anung klasing makina o machine electronic engine b o manual type lang,kpag manual type lang check kyo ng fuel line at yung lifting pump nya,o bka barado n rin ang hose dahil namaga na o kya sa tank nya,ppwede rin kung may gumalaw n nga machine mo bka nagka baligtad ang line nyan.kung electronic engine nman kailangan check power supply ng ecm,at mag check din s error system bka doon mo lang makikita ang dahilan ng problema ha

@farlymancao1097

2 жыл бұрын

@@caterpillarjhunhunk electronic na excavator to boss wala lumalabas na fuel piro mo start ang makina

Sir are you filipino

@caterpillarjhunhunk

Жыл бұрын

yes sir

36:617-8

Position 36 617 5

@caterpillarjhunhunk

3 жыл бұрын

bro that error is located at the intake manifauld, the name is inlet heater relay, 36-617-5, if that is only the error available as active ignor it, that heater is usefull if your engine is hard starting, ignor it there's no side effect for the function of the engine

36:617-5

@caterpillarjhunhunk

2 жыл бұрын

bro that error is inlet heater 617-5 open circuit 617-8 malfunctioning eigther disconnected or damage, located at intake manifold at front we have relay there check or insfection that area for possible damage

Kabayan nahihirapan ako sa english mu intindihin baka pede may english sub title ka na lang nakaka hilo eh thanks

@caterpillarjhunhunk

2 жыл бұрын

sinsya na po kung mahirap intindihin english ko,ito whatsapp ko kung may tanung k +971567581176

Sir pwde help naman aqu

@caterpillarjhunhunk

3 жыл бұрын

pweding pwede anu b ang maitutulong ko

@robelhabte6901

3 жыл бұрын

39:581-5

You are great am having the same problem engine loading now if you remove cable and no change what next

@caterpillarjhunhunk

7 ай бұрын

Bro can contac me in my whatsapp +971567581176, i need to know more

Tagalogin mo na lang kc kmi man nahirapam ding intindihin english mo

@caterpillarjhunhunk

2 жыл бұрын

haha english ,nahihirapan nga ako mag english kya lang mrami ksi n follower,ibang lahi kya kahit english kamatis eh pinipilit ko pra makasakay ung iba sinsya na,request k nlang ng pwede kung gawan ng video kung kya

@jaimecordova5780

2 жыл бұрын

May na exp ako cat 330b ayaw mag swing ano posible sira

@caterpillarjhunhunk

2 жыл бұрын

@@jaimecordova5780 maraming pweding pagmulan ng problema ang swing,una check mo swing brake solenoid nsa bandang ilalim ng control valve un 3 n solenoid ang andoon mula taas pbaba magkakasunod ung s swing is ung pinaka baba kung hindi ako nagkakamali,tpos syempre observe mo ung machine n kpag nag swing k pero ayaw mag swing pakingan mo tunog kung s function ng swing eh natunog o prang naglload sya pra mag swing,bka pwede may dalawang safety valve yan s ibabaw ng swing motor,pero bago mo galawin un pressure test k muna gamit ung self monitor nya makikita mo doon kung lload ang swing ,s pressure nya,o kya kontakin mo ako s whatsapp +971567581176

@jaimecordova5780

2 жыл бұрын

Salamat po sir god bless

Good day Sir, what is your fb?

@caterpillarjhunhunk

3 ай бұрын

Jhun Gedote