1st and foremost..........never, EVER use a torque wrench to break torque! You will screw up the calibration and it will never torque correctly again. This is what breaker bars are for.

@whobru

4 жыл бұрын

Thanks for posting..I did not know that.

@marrkcrear2946

Жыл бұрын

Thanks for the information

Torque wrench are for tightening not loosening you will strip out the teeth in the wrench. Use a breaker bar or a impact gun

@valerioventura

3 жыл бұрын

Glad I read this, I did not know that. I was just about to use my new torque wrench. Thank you!

@radarbrew

3 жыл бұрын

I was gritting my teeth watching that.

@craftman5632

3 жыл бұрын

Been using the same torque wrench to loosen and tighten my lug nuts on my vehicles for the last 20 years had no problem with it still works fine.

@blackkitty1774

2 ай бұрын

Really? Then why do they have a reverse feature?

I have been making all the same points since my wheel fell off. But the Cam Am choir boys seem to think it's a perfect design and that Cam Am will swoop in like an angel and help you on the side of the road. Good to see your video. Thank you sir...

As a tip for anyone removing a bolt like this or a top yolk bolt on a bike, use masking tape around the bolt to protect it from scratches.

On the back side of the hub (wheel), there are 2 slots that you can slide a pin into that will hold the wheel in place. Just an FYI.

Seems like the bike should come with tools required to change tire? Can Am should be ashamed for not supplying the 65 mm tool and bar!

@iluvbiggirlz420

4 жыл бұрын

I never rode or brought a motorcycle before,but do they give you tools for the bike?

Yes it is a must. Especially if you love in the country and I would say that for all vehicles you need to be able to change your tire

Yup, just got a flat Saturday and have to wait until tomorrow to have it towed to the dealership 🤦🏽‍♀️. Thank you I’ll be ordering this 65 MM socket. 👍🏽

I definitely agree, it's a must have tool if you own a Ryker, I'm waiting for mine, coming from the U.K.

@Vendetta87150

5 жыл бұрын

slyyfoxx120577 where from in the UK please?

@slyyfoxx120577

5 жыл бұрын

@@Vendetta87150 www.ebay.com/itm/65mm-HUB-NUT-SOCKET-3-4-quot-DRIVE-12-POINT-FORD-HUB-NUT-SOCKET-/262670282877?txnId=2412741715016

It's always good to be prepared for anything. I'm hoping someone do a tune up tutorial on the Ryker. I'm still holding out for the 2020 model 2 come out. Nice bike and really enjoy your videos.

@MrTonio94

5 жыл бұрын

Esias Shark III dame here, the 2020 model will have all the little kinks worked out, next summer is our summer lol

@2wrdr

4 жыл бұрын

@@MrTonio94 What is different about the 2020 models?

@mariomoore3668

2 жыл бұрын

I enjoy it to see what he breaks. This guy is no mechanic

Thanks for the tutorial. It was good.

You can get the 65mm 12pt socket for around $50 USD some even cheaper ~$30 on amazon.

Good purchase, thanks for the video

hey I got a question I have Can AM Ryker 2020 I been trying to find a video on the ABS brake sensor . I keep getting VSS code and Limp home mode and traction warning light. They said I bent the top lh swing arm I replaced it but I’m still getting VSS reading

Thank you for doing this.

Is the right tire nut direction the same as the left tire nut direction?

On the opposite side of the tire is there a bar holding it? Im trying to take my tire off but the whole thing is spinning...

That wrench looks too short for a 200+ ft/lbs of torque. Its maybe in in/lbs. And torque wrenches are for tightening not breaking a bolt/nut loose.

But enjoy your trip and ride safe brother!

Question is since you have had the bike have you caught a flat ?

Does the bike come with a jack?

For me having the socket at the very least is a must. Then if I have to call for a breakdown truck they will be able to use it with their torque wrench. That’s my plan anyway.

Heck yes. Good video.

Great video for what not too do.

Is it using bike or car tires?

Torque wrenches are for tightening and breaker bars aer for loosening

Use a longer breaker bar it will give you more leverage

When I heard 200ftlbs My first thought was I am sure it's really 300ftlbs as most will use the good and tight method. A 30 inch breaker bar would be best to remove along with a 4 foot pipe. Nice to see you used a torque wrench to tighten. Most will just stomp on a 4 foot pipe and get it good and tight. I see it all the time

You’re changing the wheel? Not the tire?

Ok. I know u probably know by now but you do not use a torque wrench to remove nuts. Get a long breaker bar or just a dewalt or other brand 20v impact. You'll love it AMD u can actually keep the socket and the impact on your bike with you.

Definitely worth it bruh!

Why are you setting a torque wrench to REMOVE the nut ???

Definitely a must

Rip torque wrench but great videos as soon I get some free time. I'm trying to get one

Perfect example why can am doesn't give out sockets. Most people shouldn't work on any critical components.

If you look at the backside of the tire you have to put an Allen key in to line everything up before you tighten the wheel to 221 pounds

It's a must. Not supplying the socket makes me think twice about buying a Ryker. To me, this is like buying locking lugs for your car but the dealer not supplying the key.

Yes, socket at the very least. Breaker bar and torque wrench will remain at the house. The socket will remain in the Ryker and if unfortunately there is a blowout, I will use a tow services' breaker bar and torque wrench and during the call ensure that they have them.

ah bruh need that info were you got that socket

Where the spare?

You don't typically use a torque wrench to remove hardware, did they tell you to do that? It's usually for install only. You just need a braker bar or socket wrench for removal.

@llcmax7853

5 жыл бұрын

If it was torque on at 220lb you need that much pressure to remove it. My breaker bar did nothing for it.

@speedandstyletony

5 жыл бұрын

Actually you will need more than 220 ft/lbs to loosen the nut but a torque wrench is meant for tightening. A breaker bar or even an impact driver would be the better tool to remove. Now when you put it back on you need that 220{actually 221} ft/lbs to keep the wheel on.

Paint the calipers red💪🏽

You might want to recheck the torque wrench spec, I don't think that is a 220 ft lb wrench make sure it doesn't say in lb(inch pound) and please don't stand on it.

for added safety, could throw some blue loctite on it as well when putting it back together.

@jamesglenn520

3 жыл бұрын

NEVER!! You will destroy the nut trying to remove it later. You don't put loctite on your car wheel studs you actually use Antiseize because of the torque requirements.

always want to be ready and safe

Do you have a torque wrench? Are there any one who is going to have a spare tire? I know you arent going to be carrying a spare because theres no place to carry one.. you shouldn't have taken off the wheel. Why are you thinking that you are going to have a flat or blow out? I wouldnt be going anywhere that I thought I would be likely to have tire damage. If you have a blowout you will have worse troubles than just repairing the tire, if you have a blow out you will have to replace the tire any how. Now for a puncture it's easier to repair the tire, if it can be repaired, while it's on the Ryker you should have a tubeless tire repair kit, and its smaller, but you will need air to pump the tire back up, plus, you get 1 year of roadside assistance with the warranty. I dont see any practical reason to remove the wheel while on the road. Now you have to torque the wheel nut back down. Do you have a torque wrench? Good luck and safe riding .

Hello. Do you have the link where you purchased it? I agree you need to have your own 65inch tool to do the work on the tires or brakes. Good stuff and thank you 4 sharing.

@MrInternationalSound

5 жыл бұрын

2nd this request

@vicnevesvn

5 жыл бұрын

Third lol

@llcmax7853

5 жыл бұрын

www.ebay.com/itm/65mm-HUB-NUT-SOCKET-3-4-quot-DRIVE-FORD-HUB-NUT-SOCKET-12-POINT-/222857281232?txnId=2232992860012

Could you share the link to where you ordered the socket please.

@llcmax7853

5 жыл бұрын

www.ebay.com/itm/65mm-HUB-NUT-SOCKET-3-4-quot-DRIVE-FORD-HUB-NUT-SOCKET-12-POINT-/222857281232?txnId=2232992860012

@rustystick

5 жыл бұрын

Amazon has it for 55 bucks

As has been made plainly clear in most Rykder videos, storage on the Ryker is basically nonexistent. I'm not exactly sure where you might carry a 65mm socket and a torque wrench in the event you have a flat tire on the road some place. Unless you wanted to lay out the cash for one of those small cases you can mount behind the rider or the side saddle bag, both of which only appear to offer minimal storage real estate. So to answer your question, I don't see the value in buying either unless for use in your own garage, but a flat on the road is still going to cost you some bucks to repair.

Id hate to see the cost for a break job!!! Just the parts must be insane!!

Great video but I have found out even if you take the tire off no auto service shop will touch it of have the equipment to remove the tire from the rim. I have just put a can of Fix A Flat in my bag which will seal most average holes.

@MrDavidelliottjr

5 жыл бұрын

Try used tire shops. Most of them will take the tire off and put on a new one or repair. I say most. Not all

@MrDavidelliottjr

5 жыл бұрын

It's the balancing that most cant do because this odd center hole won't fit there tire balancing machine

@jamesglenn520

3 жыл бұрын

I live in the Treasure Valley of Idaho and the machines at Commercial Tire shops work absolutely great. I had balance issues with my bike from the manufacturer and my CT guy fixed the problem on both fronts in less than 30 minutes 👍👍

Why are you worried about replacing a tire with a new bike ? If I were worried , I wouldnt have bought the bike to start with! I bought my first Spyder in 2008, I have had it 11 years, I have had my second one for 4 years, I have NEVER had a blow out or an unexpected flat, and i have had 12 sets of tires so far. And I'm considering buying a Ryker....

It’s good to have

if you ruin the ring that holds the nut, just replace it with a cotter pin of the right size.

Don't use a torque wrench for loosening. Also don't completely take the nut off before jacking up the vehicle. The wheel could fall off and drop the vehicle on the ground.

Yes!!

Its the responsible thing to have unless you got good friends with pickups that can deadlift 600lbs. Probably have to find a jack that can fit inside the ryker trunk. Don't know why they didn't design the ryker with zero flat tires.

But use a breaker bar to take off nut only not torque wrench

Dude...you dont use a TORQUE WRENCH as a BREAKER BAR.

Ummm, replace that jack or get some jack stands. It doesn't hold height at all.

Hey man can you show how the seat comes off?

@llcmax7853

5 жыл бұрын

Which one driver or Passenger

@nickdroomer1708

5 жыл бұрын

@@llcmax7853 driver

Man hands down I think we need the part to take the tire off. Cause you never know what will happen. If possible can you put the link of the socket in the description, cause I think people are keep asking u for the link... Lol

@llcmax7853

5 жыл бұрын

www.ebay.com/itm/65mm-HUB-NUT-SOCKET-3-4-quot-DRIVE-FORD-HUB-NUT-SOCKET-12-POINT-/222857281232?txnId=2232992860012

Maybe you should let the dealer work on it.

I see a lot of things that BRP would have to change before I would spend good money on this machine.

Yes. A must have. I would suggest wrapping the nut with electrical tape to prevent socket slippage and nut damage because the 65mm isn't a perfect fit but will get the job done.

@llcmax7853

5 жыл бұрын

Okay metal on metal somebody got to lose in these case it’s the cheap paint on it.

wont bother to go over not understanding how a torque wrench works, already been covered but you keep saying your removing the tyre, when infact you're removing the wheel with tyre attached So now you're siting at the side of the road with a flat tyre and trike on a jack, wheel in hand what next ? field repair of puncture? got the tyre levers, puncture repair kit and compressor to re inflate the tyre ? nop thought not best call recovery, oh wait, they cant load it on their vehicle because you jacked it up and removed the wheel leaving the trike immobile

And that torque wrench looks very short for 220ftlbs

Awesome. Thank You for this.

They should make sure people are schools on how to change the tire. Period

$130??? You can buy these in the UK and I am sure, the US, for £15 - £25.They are for Ford hub nuts.

You must tighten the nut to 300 lbs I don’t think you could have done that with your small torque wrench, you should take it to the dealer and have it brought up to specks, you could suffer a failure because the three small pins on the rim must be locked in at 300 lbs. Good luck with your riding stay safe..

@MrDavidelliottjr

5 жыл бұрын

I think that is a inch lbs torque wrench he may have. Lol. It's very short

🤣🤣🤣🤣🤣🤣use torque wrench to take off a nut. Lol.

90% in these comments dont even have a Ryker or even a Spyder for that matter and they wanna talk shit instead of giving advice. Lol

@marsthedude1

4 жыл бұрын

you dont need to own one to know you should use a breaker bar and not the torque wrench to untighten

that is an inch pound torque wrench, 200 in pounds = 16.5 ft pounds, your tire will be about 1/20th as tight as it should be!

@Frankietomatoes6189

5 жыл бұрын

Yep I agree, over 200 I would need a Johnson bar to tighten.

Nowadays you buy a ladder and there’s 4000 stickers on it this motorcycle with a new hub they tell you to bring it in like anyone’s going to listen

When you buy this motorcycle they should give you a small manual that shows you how to take the tires off they’re so fucking greedy They would rather kill their customers. They know people have to get the tire off

So far 10 idiots don't like you sharing good information. Whatever, you keep up the great work!

@spyderlyf3

5 жыл бұрын

10 people are trying to save him from himself. The rest are yes men..

@ontargetairsoft8532

5 жыл бұрын

The reason for the dislikes could be the following: 1 Don't jack the bike up on the A- Arms you could damage them. Jack up on the bikes frame. 2 Use a rod or Allan key to lock the wheel from the back side like intended 3 Never use a torque wrench to loosen a nut you will damage the wrench. It's a precision instrument. Use a breaker bar. In one of his replies he says he couldn't get the nut off with a breaker bar and set the the torque wrench to 400 ft-lb to get it off. What? This shows that he has no idea of how to use a torque wrench. And there is no way that wrench has a 400 ft-lb setting 4 I could be wrong but I have never seen a torque wrench that small capable of 221 ft-lb. Mine is over 2 ft long. It needs to be that long to be able to apply that high torque. My100 ft-lb wrench is longer than that one. 5 When using a torque wrench never jerk up and down on it to get to the desired torque. Even pressure till it clicks. 6 Tighten the nut with the wheel in the air so that the wheel centers on the axel properly and is torqued correctly. 7 Re torque after a number of miles This is really important to be done correctly as we have seen. Even some dealers can't seem do it correctly. I hope his wheel stays on and he doesn't have any problems. Just my 2 cents.

@giovannam925

4 жыл бұрын

@@ontargetairsoft8532 your 2cents could save a life.

Millimeter not minute meter!

Good video

put a tube extension on the handle to increase the leverage and therefore increased torque.

Carry a can of fix a flat and some tire plugs

all i can say is, LMFAO !

Breaker Bar...20 bucks

Look up seller "YunShuo" on Amazon. $17.09 plus shipping

@tsovdigmuag9667

5 жыл бұрын

its not there

Torque wrenches don't apply torque. They are used to measure the amount of torque used to tighten a nut or bolt. Breaker bars are used to break loose a bolt. You have to use one of the correct size to get the job done. Thanks for trying to make an informative video. In the future please find out the correct procedure before you attempt to teach something.

Uh my man you better put that wheel back on with 221 torque pounds or your wheel may fall off Goin down the road. There is another guy on KZread that the dealer didn't put the correct torque on it and his wheels fell off. If I were you I would just use the can am road side assistance that came with the bike.

@llcmax7853

5 жыл бұрын

My New 2019 Torque Bar has a ( Click ) when you reach the torque. Also, it half the size of a old torque bar. Keep in mind if everyone that buy this have run back to dealership make sure it’s correct. There going be some long lines. I’ll trust my work over any local dealership employee who is just ready go home. Doing a half job put these machine together.

@tarheelmp8051

5 жыл бұрын

I get you I trust my work more as well just a heads up man. No offense intended! I know I had to order a torque wrench that would put the correct torque on it when I bought mine. Stay safe out there and keep the videos comin love the channel

@giovannam925

4 жыл бұрын

@@llcmax7853 where did you get this torque bar that is half the size. Doea it fit in the frunk?

Ho mon dieu . Un clef dynanometrique pour démonter. Pfff . Pourquoi ne pas avoir pris un clef à cliquet. Normal. Tu abîme ta clef à démonter avec ça.

Used a pipe.

Lots of talking

That's not a proper torque wrench for 220 FOOT LBS !!! I have that small 3/8 " drive one, as well as the bigger 1/2 " drive longer torque wrenches. Both don't have a setting for up to 220 FT LBS. You'll need the huge torque wrench to properly set that tire on! You probably set it to 220 INCH LBS, which is waaaay too loose. This is an important safety issue. Look what happened to another ryker rider who had the dealership assemble his trike to have the tire come off at 800 miles. m.kzread.info/dash/bejne/eoGhyKqcYrSwmMo.html profanity used, but he could've died from their incompetence!

You don’t use a torque wrench to take something off it will mess it up