Yo G! Did you mention this can be setup for some switches used for constant power (battery power) and some used for switched power? Example: car off and still able to power dome light, rock lights, and whips while all other switches are powered with key on (switched power).

@GLifeUTV

3 жыл бұрын

I did vagley say it. When i explained start stop must be set to battery power.. but you are right. Im going to pin the comment so more people see it 🤙

@bammortgage

Жыл бұрын

Thank you for that clarity

At 1st it's seems overwhelming, but once you take a moment to break it down. It's a great idea!! Wiring can be fun and challenging. It can also be a nightmare!! Thanks Frank!!👍🏼

@GLifeUTV

3 жыл бұрын

Well said👌👌

What a great device, awesome video Frank, keep em comin brother.

@GLifeUTV

3 жыл бұрын

Thanks brotha. Appreciate it 👌

Pretty slick brother. Really good video. I like the ones with a termination unit tho just because I don’t like all the spade connectors. 100x better than have a single switch and relay for every device tho.

@GLifeUTV

3 жыл бұрын

Thanks bro. I think its well worth it

You the man frankie!!!. All your videos coming in clutch!!. Im installing the 8 button switch pros on my x3. Thanks for the help!!. Haha

@GLifeUTV

2 жыл бұрын

🤙🤙🤙 sweet.👌

Definitely a nice product to have. Nice video like always

@GLifeUTV

3 жыл бұрын

Heck yeah. Sucks cuz now i want one. I must resist

Great job Frank learning alot from you keep up the videos.

@GLifeUTV

3 жыл бұрын

🙏🙏

Awesome video bro! Always learning. 🍻

@GLifeUTV

3 жыл бұрын

🍻🍻🍻

10k of the 44, 000 views were probably from me 😒🤦🏼‍♂️

@aaagarcia3920

3 жыл бұрын

🤣🤣

@GLifeUTV

3 жыл бұрын

Haha.. thanks times 10k then

Great vid! Now I’m ready to install mine as I was completely lost before watching. Can you control the colors and strobe sequences on the 5150 whips from the switchpro app or does one have to use the regular app that they say to use?

@GLifeUTV

2 жыл бұрын

You still have to use the 5150 app

2021 what a time to be alive 🤘🏼

@GLifeUTV

3 жыл бұрын

Haha🤙🤙

Is there any way to use the switch pro for ignition off a secondary battery? I know ignition is currently on the primary battery. I’m going to set accessories to run off secondary battery.

Great vid man!

im installing a switch. do I use the highput to install my rugged radio or use one wire?

Me and you definitely have two different definitions for “simple” boss man 😂😂

@GLifeUTV

2 жыл бұрын

😅😅😅😅😅

Im trying to dp the push to start off my auxbeam 8gang but dont knoww what wire is hot out of the 2 and where it goes ans the other also

🏆🏆🏆👍🇺🇲🙏 Thank you for sharing

@GLifeUTV

3 жыл бұрын

Yessir 🤙

Any video on running your own wires to switch pros instead of using provided harnesses with lights. For instance the LP4's ?

@GLifeUTV

2 жыл бұрын

Sorry i dont have a video on that

Love that idea behind all of this and the product seems amazing but 1k for a switch board and controller is steep

@GLifeUTV

3 жыл бұрын

Thanks ill look in them🍻

If your Switch Pro is on constant power. meaning the key or start button do not need to be on for the Switch Pro to function, then do you still need to tap into a different ignition power for the Start/Stop to work on X3?

This thing is insane!

@GLifeUTV

3 жыл бұрын

🤙🤙🤙

Im having an issue getting my lights to be on constant and then strobe on double click.

Can you use the switch pro to open and close the evo shocker exhaust valve?

That is so bad ass, how long did it take to install from start to finish. What do you do with the holes from the old switches

@GLifeUTV

3 жыл бұрын

Does take la good saturday to get everything done. But i think its worth it.. most switches slots have caps

So if your not have the 12 start the car can you use the accessory post when programming? And then will it still run whips and rock lights with car not running? Thanks for help

@GLifeUTV

Жыл бұрын

Yes... As long as you set the switch for ships to battery on function

Ok, here is how you make the stop start work correctly. One channel goes to the black/yellow wire on momentary setting. The switch pro blue and white wired to the red/black on the 4x4 switch. I am using an 8 gang switch pro. I used and #8 goes to the black yellow. On the app, turn switchpro and then tap/hold down momentarily #8 to start. Boom....you have lift off!

@mannyahles1161

Жыл бұрын

@@GLifeUTV Edited. I was just trying to be funny. Sorry. I enjoy your videos.

@GLifeUTV

Жыл бұрын

@@mannyahles1161 all good🍻🍻

What about wiring the Lt blue ignition wire to its own switch, off battery power? I have to use the phone app to wake up accessories even to light up the 4x4 switch. Then I am able to start / shut down the unit. Pretting start button doesn’t wake up accessory lights

@GLifeUTV

3 ай бұрын

If you're using the start button (on switch pros) to wake up the vehicle. Then that start button needs to be set to battery function. So Start button can work at all times

Ey brother great información on video Just one question you run one power wire for star button directly to the battery ?

@GLifeUTV

Жыл бұрын

No switchpros powers the start button

I have this same model of the switch pros on my x3 and was wondering if it works with the shocker exhaust from evo? I just got the exhaust and haven’t put it in yet but didn’t see in your video that it was operational. Great videos as always.

@clayyerrington6756

2 жыл бұрын

I just went down in the tread and saw the conversation about this… Haha! Thanks for the help!

@GLifeUTV

2 жыл бұрын

Note may void warranty but Yea. There are 3 wires going to the evo shocker actuator. Red needs constant battery + black constant ground - and the white wire gets controller by the switchpros on and off 12v

@clayyerrington6756

2 жыл бұрын

Hell yeah man. Thank you again. Always look forward to you new videos.

Can you run a rugged radio and intercom from the switch pro

How did you wire the Shocker into the switch pros other than power and ground “red, black” where do you wire either green or white wire from shocker so that it closes?

@GLifeUTV

2 жыл бұрын

black goes to ground, red goes to battery hot, white or green cant remember, it only uses one of them not both. is the wire you control on and off with the switchpros.

@jamesmaloney9228

2 жыл бұрын

@@GLifeUTV yeah I did red to a output on switch pros black to ground and it only opens won’t close so figured gotta wire one of others to power

Wish I could afford that it's bad ass!

G gotta question have you had your dess system stop working because of your switch pro being used for ignition I installed the switch pro the way you did from watching this and it’s worked great for about 4 months well all of a sudden my dash starts saying could not recognize key and the dealer is trying to blame it on the switch pro I find this hard to believe because it worked for as long as it has and i don’t see why this would have any effect on the dess system?? 2022 XRS TURBO RR

@GLifeUTV

Жыл бұрын

It shouldnt affect dess system at all.. ive installed many. And none have had issues

@HuffysBackyard

Жыл бұрын

@@GLifeUTV thanks brother that’s what I was thinking I appreciate it

Have you used the force 12 on a pro r with the start function like in this video?

@GLifeUTV

6 ай бұрын

I have not

@scottedmundson3970

6 ай бұрын

Thank you for the quick reply

Bad ass 👍🏼

Do you move the white and blue wires back to the accessory post after you're done configuring all the switch settings through the app?

@GLifeUTV

2 жыл бұрын

no, in this example they are powered by the backlighting from the 4wd switch, that is the ignition source. if you use the ignition source from the ign post it will power cycle the switchpros everytime u try to start.. this is only if u want to start vehicle from switchpros. if not you can use the accessory post as ur ign to power switchpros

@salehgt46

2 жыл бұрын

@@GLifeUTV Got it. Thanks for all the info, your videos are a huge help.

@ernestolinares9811

Жыл бұрын

What is the difference on connecting the ignition wire to the backlight on the 4x4 switch and just wiring directly to the battery?

I’ve been looking into getting the rcr 12 for the can am, would it make the wiring simple for all the stuff we’re going to be getting for it? For example I have baja designs lights and don’t like the harness they come with and would rather have it connected to switch pros, would it be just having the power and negative setup to the switch pros? Or would I need the baja designs harness for it still

@GLifeUTV

2 жыл бұрын

It would just be positve coming from switchpros to bd light and a negative straight to ground from bd light

@drewfoster1493

Жыл бұрын

I am confused on this. I have BD light bar. The harness has a positive, negative and ground. What do I do with the ground wire/relay looking thing on the harness?

@litonica2002

Жыл бұрын

@@drewfoster1493 i’m pretty sure you can just cut it out, the control module for the switch pros should have the relay in it already built it so you’d just need the negative and positive i believe. i could be wrong though but from what i understand i believe that’s how it works

@drewfoster1493

Жыл бұрын

@Rxvl_ so do I cut the wiring harness that goes to the relay and in there would be just two wires?

@litonica2002

Жыл бұрын

@@drewfoster1493 i think so because the module should have the fuses for the light bar built into the switch pros so you wouldn’t need the relay that is on the harness they give you but i would ask frank to be 100% sure i don’t wanna give you wrong advice and just say yes

i just got my switch pros for my pro xp.....any idea how to do an ignition auto-start on it? I need to look chingon like CJ & Timmy! Go Doyers!

@GLifeUTV

3 жыл бұрын

Couldnt tell u brotha.. download the schematics/ service manual for the pro xp

@shreqboi1

3 жыл бұрын

Let us know when you do!!

What ignition source do you recommend for the ignition wire?

@GLifeUTV

Жыл бұрын

The red with black wire. On the back of the 4x4 switch

Can the blue and white wires be connected to the middle post that is full time hot?

@XxTaVo205xX

3 ай бұрын

Full time hot. Switch pros light would not turn off

What’s up Frank. Your videos are very informative. Can you tell me how you wired the exhaust to the Switch-Pros. The lights consist of power and ground but the Evo exhaust exhaust has a green and a white wire and I am not sure how to wire them. I Appreciate your help.

@GLifeUTV

2 жыл бұрын

There are 3 wires that go to the actuator on the exhaust.. one is ground, one is constant power and the other is power control on and off... You will need to provide power and ground normally thru the power distribution near the shifter on the x3. U can have the power control circuit be controlled by the switchpros. Note i can cut the grey harness. Just dont cut it to close to the original exhaust switch in case u need to reconnect the switch harness

@dannydeharo8243

2 жыл бұрын

Thanks for the quick response! I actually have four wires. Power, ground, the white you described. When I tested them, it seems that power and white open and the same power and green wire close it. Would that mean that I would need to wire all three power white and green to the Switch-Pros? Sorry for the question this one is really throwing me for a loop.

@GLifeUTV

2 жыл бұрын

@@dannydeharo8243 your talking about the wires at the actual switch. There should only be 3 that go to the actuator on the valve

@dannydeharo8243

2 жыл бұрын

@@GLifeUTV there are three coming out on the valve but there are 4 when I cut the harness. Kinda caught me off guard I though there would only be the three showing at the connector.

@GLifeUTV

2 жыл бұрын

U can dm on ig with photos if youd like. But i just did it to my machine. And u only need to deal with the 3 wires that go to the actuator

FRANK IS THERE ANY WHERE ELSE THE MAIN BRAIN TO THE SWITCH PRO CAN GO??? THAT AREA IS WHERE ROCKFORD FOS GATE PUTS THERE 2ND AMP? THANK U

@GLifeUTV

2 жыл бұрын

Ive seen guys put it on the rear wall above battery

@geraldmaez9672

2 жыл бұрын

THANK U

I have baja design pod lights. Coming off the light is a black and white? What's the set up for a black, white amd ground?

@GLifeUTV

Жыл бұрын

If u mean black white and green.. the green is used for different function.. for s8 it is for the amber backlight using a power source..... if its the green wire for onx6. Its used as a dimming circuit for the light and gets grounded.

@mattficken8975

Жыл бұрын

@@GLifeUTV where would you hook up the green to work the Amber's? Separate switch?

@GLifeUTV

Жыл бұрын

@@mattficken8975 I normally do them to the ignition or accessory circuit. so they turn on automatically

We out here

@GLifeUTV

3 жыл бұрын

Yessir🤙🤙🤙🤙

So i got mine installed. But im not understanding the starter issue you had with the lt blue and white on the lower post. If you have acc power behind the other toggle switch. Its the same as acc power? Where was the rocker switch hooked up that made it different?

@GLifeUTV

2 жыл бұрын

The ignition has to go to the rocker switch if u plan to use remote start feature... If u use the accessory post, the post wont provide power unless the engine is on.. so from what we experienced. Since the accessory post only provides power when the start button was pressed or engine on. It would reset the switchpros Everytime and would not start properly due to ignition turning on and off

@GarSeeYaa

2 жыл бұрын

@@GLifeUTV so when engine is turning the acc post kind of cuts in and out so that makes the power come and go. On the rocker switch you tied into constant 12v or acc 12v? Cause if its acc 12v shouldnt it be the same thing as lower post. I see where the issue came just not making sense on the tie in of the rocker if its acc it should reset it the same. Or is it due to the back light on the rocker when engines on. That feed should still come from acc?

@GLifeUTV

2 жыл бұрын

@@GarSeeYaa The rocker switch powers the backlighting and it wont cut out... I have done it to multiple machines. Its the only way

@GarSeeYaa

2 жыл бұрын

@@GLifeUTV gotcha well ima have to tap into that 4x4 wire you tapped into looks like the red wire. Thanks G

@GLifeUTV

2 жыл бұрын

@@GarSeeYaa 🤜🤛

How many extra switches do you get with the 8 switch set up

@GLifeUTV

2 жыл бұрын

None.. 8 switches are tied to 8 outputs

Is CJ running a aftermarket battery or dual batteries?

@GLifeUTV

3 жыл бұрын

Utv stereo dual battery kit

Great content! Did I miss the Glife discount code from switchpros ?

@GLifeUTV

3 жыл бұрын

I missed it too 😅😅

@kurtmcmichael2045

3 жыл бұрын

@@GLifeUTV lol. They are a great product for sure. Been Watching it for a few years now.

That’s bad ass bro

@GLifeUTV

3 жыл бұрын

🤙

Hey mate, how did you guys set it up to start and stop off the same switch?

@GLifeUTV

Жыл бұрын

Yup, it just acts as a momentary switch just like the factory one

@macauleygilmore2985

Жыл бұрын

@@GLifeUTV oh sick! How did you programme it on the app tho? Because I’m trying to programme mine atm. The stock has two switches on and off and want to use the switch pros on one switch to turn on and off. I have two switching cables on and off to hook up to the one switch pros button.

Yo questio bro. On the switch pro. I see you have the dual battery set up. Is the dual battery still functional where you are running your acc. Off the hot wire? Or are both batteries on at all times now?

@GLifeUTV

2 жыл бұрын

On this machine we eliminated the solenoid . Both batteries are always hott

@GarSeeYaa

2 жыл бұрын

@@GLifeUTV gotcha. I have the dual battery set up. Can i run the switch pro through the hot wire on second battery. (Using switch pro for ignition) And leave the the start up battery as back up. Will it still function?

@GLifeUTV

2 жыл бұрын

not 100% on that one.

"clicky switch" 😂🤣😂

I wanna send my can-am all the way from Chicago just so you can do all my wiring!! I don’t have someone that’s this detailed near me! 😢

@GLifeUTV

Ай бұрын

😅😅😅

is the switch pro 8 bluetooth aswell?

@GLifeUTV

3 жыл бұрын

Yes it is

Do you have battery issues running all the lights and stereo on long night rides?

@GLifeUTV

3 жыл бұрын

All can ams have a poor charging system. Best bet is running a bigger battery as a bigger "fuel tank"

@dannyelliott8391

3 жыл бұрын

They make aftermarket stators that are bigger than stock. They can be expensive but not as much as you think.

@GLifeUTV

3 жыл бұрын

@@dannyelliott8391 wasnt aware of any aftermarket stators.. i know most are upgrading to the 21 stator. Or getting the expensive zrp alternator kit

@dannyelliott8391

3 жыл бұрын

@@GLifeUTV EVO makes a 850w upgrade over stock 650w for $650. evopowersports.com/products/850w-stator-upgrade-kit

@dannyelliott8391

3 жыл бұрын

There was another company that had more. Will have to find it again.

what amber lights do you use for dust? tia

@GLifeUTV

2 жыл бұрын

Squadron Pros and Lp4s

@rquarantine

2 жыл бұрын

@@GLifeUTV thank you brother...love your channel

@GLifeUTV

2 жыл бұрын

@@rquarantine 🤙🤙

19:15 Shout out to that old school Monti SS back there 😎

@GLifeUTV

2 жыл бұрын

Its an el camino. But thanks🤙

@JeepTJay6

2 жыл бұрын

@@GLifeUTV Every bit as bad ass. Are you up on Cleetus Mcfarland? He's got a SICK one that does 8s in the 1/4 mile I think. BTW thanks for posting this. I ordered a cheaper Auxbeam switch kit last week but then discovered the Switch-pros kit. I literally couldn't stop thinking about it after watching this and a few other videos. I decided to order the 9100 yesterday. Just pawned the Auxbeam off on my buddy. Cheers.

@GLifeUTV

2 жыл бұрын

@@JeepTJay6Mullet is a badass machine. I wish mine was that clean .lol one day.. and yea thanks for watching the vid👍

What chase light is that?

@GLifeUTV

3 жыл бұрын

Build in led strips made by cage manufacture desertworks

Hola disculpa cual es el cable que agarras para el sistema de ignición

@GLifeUTV

2 жыл бұрын

The red wire for the rocker switch

@marcosoceguera2377

2 жыл бұрын

@@GLifeUTV the red wire is what goes to the cable of the button that fs start signal?

@marcosoceguera2377

2 жыл бұрын

??

What light bar is that??

@GLifeUTV

3 жыл бұрын

amzn.to/3y2tIsA

i should be able to run this on an ATV correct?

@GLifeUTV

3 жыл бұрын

Yes, but i would think most atvs have a poor charging system and small battery

@lonestarangler8407

3 жыл бұрын

@@GLifeUTV ah gotcha! makes sense. I have a 2005 Honda Rubicon and i custom fabricated some LED headlights, i have rock lights, i have a winch, and looking to put a small LED bar on the rear and another up front. The Rock lights are currently ran to a rocker switch panel and i plan on running the rear & front LED's bas to it as well (3 switches) but i know the panel is not water proof. thats why i was wondering about this set up

22:59 You could have an on/run button, put the SP ignition wire to that button in on/off mode. Put another momentary to hit the starter solenoid.

@GLifeUTV

2 жыл бұрын

Yea thats an option

with a 12 port switch pro you get 17 switches?

@GLifeUTV

2 жыл бұрын

U get 17 outputs.. so 1 switch can for example control 2 outputs... 1 switch can be first press 1 output or 2nd press of same switch a different output..

@mikemendez8665

2 жыл бұрын

@@GLifeUTV ok great so i will get a 12 switch set up

Looks like a rats nest compared to the Auxbeam panel.

You lost me on the ignition start didn’t understand the blue wire then we’re you ran the blue and white wires you had for the power button

$1k

If only it didn’t cost 1000$ bucks 😭

@GLifeUTV

Жыл бұрын

they have the 8 switch for 600

Ey frank cunto me cobras por aser el mismo aparatillo en mi carrito??🤓

@GLifeUTV

Жыл бұрын

Dm por ig

Dome lights link ? Porfas

@GLifeUTV

Жыл бұрын

These were bought by desert works a long time ago. We don't know the brand... I saw these on the website. They're made in the USA and I run them on my machine and they're hella bright www.glifeutv.com/products/halo-billet-rock-dome-light?_pos=1&_psq=Dune+g&_ss=e&_v=1.0&variant=42814643962074