Love your informative videos Louie. Great information. I've heard that belts when new are not directional, the arrows are only for putting a used one back on the same way it came off. As it needs to spin the same way once it's been used.

Good job my friend ... thx for all the good info. Part 1 was solid too.

@PowerModzOfficial

5 жыл бұрын

many thanks for watching

Great info. I got here because my daughters 2020 can am outlander with 78 miles center bolt from her secondary clutch popped out. The bolt cracked. Im thinking this bolt from the factory should be a high tensile strength because it plays a huge roll in keeping resistance on this spring full time. Thank you for the video. Im going to go back add locktite and a torque to this. Thank again.

amazon and ebay sell and angle gauge tool cheap. i use it for degree settings(block bolts mostly) enjoy your vids!! thanks for all the info

@ronaldfontenot654

2 жыл бұрын

What's the name of the tool? Also the pitch of the all thread if you perhaps now?

Where can I get that holding tool for the stud installation?

What is part number of the clutch lock up tool???i can’t find it online anywhere??just bought same dalton kit for my renegade xmr1000

How do u like the clutch kit, does it make it for responsive, and pull harder, I have a 2018 xmr 1000 renegade

when are you going to start getting the snowmobiles back into the videos? Did you sell the axys because of the low snow conditions in the last few years, to be able to buy the xmr?

Hi looking for a little help the primary clutch stud, comes out to insert removal bolt I can't find the tourq spec for the stud itself your videos didn't remove it, so didn't cover that, do you by chance know it? Thanks 2017 xmr 1000

I got a 2018 can am renegade xmr1000r and I put a dalton clutch kit in it and instead of putting the stud and nuts in it a just put the old style bolt in it and it is way better got it from my dealer

I am trying to find the countershaft holder and the other tools and I cannot find them anywhere please help

you don't have to sand the surface area of the clutch? seems like since you had it out you could have went horizontally/vertically with a scrub pad

What is torque for primary nut thanks

So what you are saying is, if we invent a clutch spring compressor, patent it, then we can retire? Good video man! I don't even own a bike yet here I am!

@PowerModzOfficial

5 жыл бұрын

there's only one way to find out!

on 570 both primary and secondary are just torque to yield bolts. interesting video a lot different tho.

Please help!!! Does anyone have the secondary stud removal tools used in this video?? I.e the countershaft holding tool and stud remover

New to quads. What the reason for the clutch kit ?

Are u going to the Toronto sled show?

I want to now if u sell the clutch tools for the Xmr 1000

How much r the tools..i need them for 850 xxc..do u no

Hey, ive been looking for that exact clutch holder that you've got here, can you please tell me where, or if you're able to order one for me, thank you.

When you gonna do a update on the monster elan would like to see that thing rippin! It’s been forever

It's time to get the sleds ready !?

Get yourself a nytro 1000 the 121 x15 track nytro Fx they come with Fox floats and they stand straight up and down

Skid plates/C.V. boot protectors!

The only part I needed to see is the struggle to put it on 😢

Or do now where I can get them

Brp does not have the tools please send link

is there a link to buy the secondary tool for removing the secondary stud? i just bought the stm for my 19 outlander max xmr to pair with my cvtech primary

@PowerModzOfficial

3 жыл бұрын

BRP

Will 28/10/12 tires fit on the front of a brute force with out a spacer?

@ 5:03 sounds like ceramic composite.

I have the 2017 version of this bike, noticed you put the BRP belt back on after the clutch kit. Any recommendations on aftermarket belts for these machines? I really like the new beadlocks and 30” Cryptids...tempted to get a set for my XMR. Thanks for the videos btw...I enjoy your channel.

@PowerModzOfficial

5 жыл бұрын

ya id have no issues running an ultimate or other belt.

@canadaplace2be176

4 жыл бұрын

Mavericks trail belt is the best. I have both machine. I seat melt yet?

@canadaplace2be176

4 жыл бұрын

U seat melt yet 2012 2018. U will see tin foil tape every where. It is one major flaw. Muffler right under ass. Power this bike is 89hp low gear. Mine slowly breaking in 148km do far was 114km

Could we get a snowmobile update please ?!

Watch pitch is the m10 nuts

Id like to have your knowledge and work with you great job..

how did you get the cover off without removing the entire footwell?

@PowerModzOfficial

2 жыл бұрын

its tight - i think i used a universal

Can't believe Dalton started on ice ovalls

I just buy can am and ride I have never needed anything but new tires. I don’t try to break it that costs money!

a lot of work for a new bike. >?

I can’t access your website from Greenland. It says I can’t access from my country.... whats the reason?

@PowerModzOfficial

5 жыл бұрын

try again we have changed it ...I think...

@ujarneqsrensen8745

5 жыл бұрын

PowerModz just tried again, still no joy. Just wondering, if it did work, would you be able to ship to Greenland?

@PowerModzOfficial

5 жыл бұрын

it depends on what you need but I can ship pretty much everything. email me at Lshobie AT yahoo dot com. and let me know what you need!

@ujarneqsrensen8745

5 жыл бұрын

I’d love to, the problem is that I can’t see what stuff you have without accessing your webside. I used to be able to get in when the website was new, for some reason it won’t let me in now. I’d like to see what you have for a 2016 Axys 155” 800.

Why are you on your stock wheels

@nathanfleming6483

5 жыл бұрын

Gavin Burkett he explained that the factory cryptids are called 30” tall but they’re actually only 29”, so he bought some actual 30” ones. In the video he has the actual 30” tires on bead lock wheels but the rear are stock. He made a video installing the new tire and wheel combo, but I guess this was just filmed before that.

And Just like that.. I wanted a YAMAHA. Reminded of me why snowmobiles are so expensive.

Dealership o good know. Tools can am will lend it out.

can you go back to snowmobiles?

@wyattlepage

5 жыл бұрын

Lol bruh there's no snow 😂

Lol that guy. Ya don't get wet drive 300 km first. I just put second tank in it. I do not know how to get my Stuff on here.?

Wow this is exactly why I’m not a can am or ski doo guy. Way way way over engineered. Great skills though and yeah they do it so you have to bring them to the dealer and pay that $100 plus an hour shop time.

@LucidDream34

2 жыл бұрын

Man this is the exact reason I swapped to Can-Am compared to dealing with the wet clutch

Just like. Skidoo. How many times u do that that's my bike. Yes it need lock. Right wheel not locking that good 7.7 hours it's mint. It's causing nothing but havoc in my town people fucking hate us n dirt bikes oo n cottage love see does.

This voids warrenty.

6 month warranty I got. Why. Because of all u guys that take it and mud burrie it. White meetal bra. Got in a fight some guy said got spray with gravel. Lol ooh she throws

E

gloves? really?

@PowerModzOfficial

5 жыл бұрын

yup really, you'll understand one day.

@Whatsintheshop

5 жыл бұрын

I've done more mechanical than you ever will. I agree it's good to be safe though.

Liein?

Can Am / Polaris both cheap badly made overpriced bikes.

@wyattlepage

5 жыл бұрын

Lol

@atibbo

5 жыл бұрын

polaris is cheap as dirt