Nice to make it work with the oldschool parts! It's still fine with a single L motor without much load on it, but I wouldn't test it with a loaded buggy motor, connectors will melt soon :)

@marxpeklegotechnicdesign3

3 жыл бұрын

That.. sounds like a challenge..😉

@RacingBrick

3 жыл бұрын

@@marxpeklegotechnicdesign3 don't forget to turn on your camera and prepare the fire extinguisher :D I managed to melt the PF extension cable's connector with a "simple" 3S LiPo at 14V :)

@marxpeklegotechnicdesign3

3 жыл бұрын

@@RacingBrick hehe i will! But lipos are a different story.. most of them easily provide over 30 amps, while the buwizz is still capped at 5A (surge). I am not sure wether it will pop at 10a or 5a in series, should still be 5A. Do you?

@ribel6520

3 жыл бұрын

@@marxpeklegotechnicdesign3 if buwizz are connected the same way you connected them in this video 5A cap will stay the same.

@RacingBrick

3 жыл бұрын

@@marxpeklegotechnicdesign3 not sure about that but I'd be careful :)

I can’t decide if it’s genius or just crazy.. probably both:)

You’ve said it now. You’ll have to do this for the MOCs. Can’t wait so see how fast they go.

@marxpeklegotechnicdesign3

3 жыл бұрын

If it serves a purpose.. 😁

You are a crazy dude. I would be too afraid to do that.

your a madman!!

You do great things

very crazy so much speed i build your Tracked Racer and the Off Road" Buggy and have a lot off fun .

Cheater mode : on

22.5v is probably pushing the limit of the motors. I have had them pulling 20w and things heat up pretty fast. I suspect their rated for ~25w with an operating voltage from ~6-24v. So the average of 7.4v limited to ~1.5a would be well well within a margin of safety an longevity. Remember these are meant to be "toys" so liability and all. I would not recommend doing this if the motors are going to be under any serious load. If my assumptions are correct 2 packs like this could allow the motor to draw (22.5x1.5) over 33w which could damage the motor or worse a lithium fire.

You never fail to amaze me! BTW I purchased two buwizz motors through your link😀

@marxpeklegotechnicdesign3

3 жыл бұрын

Thank you so much! Can i ask when you ordered them?

@stihlgoin2877

3 жыл бұрын

Sure, December 6th. 2020. Once they arrive I'll probably make a trophy truck of some sort. Currently I have built a sort of dune buggy. Not since theres snow on the ground I put skis on the front. Priviously I had tracks on the back, but we're to slow for my liking. It doesnt steer to well due to the fact that theres no castor angle.

@Monster-st8hb

Жыл бұрын

@@marxpeklegotechnicdesign3 I ALSO DID SO...... THANK YOU!!!!!!!!!!!!!!!!!!!!!!

good god thats amazing

Perfect Idea for REAL fast Modells 👍 THX man

@marxpeklegotechnicdesign3

3 жыл бұрын

Be careful. Only do this at your own risk and dont forget the amps are doubled aswell!

@chrissmarduksrccarcarnage4940

3 жыл бұрын

@@marxpeklegotechnicdesign3 yeah I know that but I Tested the Lego motors Up to 24volts and they are still OK...👍

@basberend

3 жыл бұрын

@@chrissmarduksrccarcarnage4940 you might be better off using a 4S lipo/life battery. 16.8V and put a amp restricor on it.(diodes i believe) ( however I am not quite sure how to make this) an LDO can be used to restrict the max Voltage.

@chrissmarduksrccarcarnage4940

3 жыл бұрын

@@basberend Thx man I will try this ...I have enough ESC s and lipos from 1s to 6s because of my RC Car Hobby...🤘

@Monster-st8hb

Жыл бұрын

@@chrissmarduksrccarcarnage4940 WHATTTT? THE LEGO PF CABLE CAN'T HANDLE THAT MUCH VOLTAGE !!!!!!!

any news about buwizz motors? i saw they appeared on the site

@marxpeklegotechnicdesign3

3 жыл бұрын

Yes. You can preorder them now and they should arrive in februari. Please dont forget to use my link when decide to order: buwizz.com/?ref=16 You can also expect a review video once mines arrive.

6.0 with two 3.0 s pls

On my channel you might like my servo mod for lego racers? Also you wouldn't happen to know how many volts the lego racers buggy receiver can handle? I've tested it with lithium AA,s and got around 9.5v loaded.

@marxpeklegotechnicdesign3

3 жыл бұрын

I just saw your mod. Why did you do it? And it doesnt seem to be proportional, is it? I think it might also work by just hooking it up to the grey AUX port and use the paddles? Im not sure about the max voltage. But i heard people trying with 3 lion 4.2v baterries that burned them out. I wouldnt go too crazy if you dont have spare receivers.. once you go too high they are dead forever (unless you can replace/find damaged components)

@DBZLEGENDS

3 жыл бұрын

@@marxpeklegotechnicdesign3 i did it for my trophy truck. The grey port will not work because the lego servo is a true 4 wire servo. Also most mocs you don't have room for a shaft to the steering rack.The steering is not proportional but it is extremely responsive. The throttle is proportional. I tested the voltage today it can only handle 11.5v basically 12v the energizer lithium run nicely at 10.5. I found out the max because I cooked the throttle as soon as I hooked up 15v. The trigger input still works thankfully. drive.google.com/folderview?id=1hJ5rJiwPIwIc4leDZXbOuG3jA6EolGsG

@marxpeklegotechnicdesign3

3 жыл бұрын

@@DBZLEGENDS good to know about that voltage and that the aux port wont work for servos. And i can see why you extended it, nice truck! By trigger input you mean the grey aux port? Be carefull with that one, it cannot power buggy motors, it burns out on high loads from what i hear.

I did this a year before you lol

@marxpeklegotechnicdesign3

Жыл бұрын

Great minds think alike! Did you get it on video?

@lmarcotte7057

Жыл бұрын

@@marxpeklegotechnicdesign3 no I didn't I'm always to lazy to post

@marxpeklegotechnicdesign3

Жыл бұрын

@@lmarcotte7057 too bad, i'd loved to see it, i subbed anyway!

2-pack

Putting two in series does not make this a BW 4.0

Rather use the buggy motor instead

I am the 1000th viewer