Building an RC boat - can I make a Chris Craft Corvette out of an Aeronaut Victoria? Part 3.
Work continues on the hull, but there is a major disaster. Can it be salvaged?
Жүктеу.....
Пікірлер: 42
@christopherjensen5007 Жыл бұрын
Excellent! The white and red really pops!
@modellingmisadventures
Жыл бұрын
Thanks very much. I like those colours too.
@niallbyrne6853 Жыл бұрын
Well done Peter, looks great.
@modellingmisadventures
Жыл бұрын
Thanks 👍
@brianboccuzzi730011 ай бұрын
That looks great! Thanks for sharing.
@modellingmisadventures
11 ай бұрын
Thanks very much. Check out the later videos to see where things are up to.
@jamescoxall322 Жыл бұрын
Looking great
@modellingmisadventures
Жыл бұрын
Thanks very much.
@robertschmidtrcmodelboats64837 ай бұрын
Looking good. I use finishing resin inside the hull and on the exterior to seal from water and once sanded smooth fills in all gaps, seams and cracks for paint.
@modellingmisadventures
7 ай бұрын
A lot of boat modellers do that but I built this one as the instructions as said.
@jjrotogeek Жыл бұрын
Very cool!
@modellingmisadventures
Жыл бұрын
Thanks 👍
@ricardosmidt96003 ай бұрын
Nice boat !
@modellingmisadventures
3 ай бұрын
Thanks!
@poepflater4 ай бұрын
I think port holes would be beter filled by sticking it on a bit of resin tape then filling the glass area with a bit of clear UV set resin and hardening with the little torch
@paulbriggs307211 ай бұрын
So that you know, when Chris Craft delivered new boats, they painted their hull sides with fairly gloss enamel, but like most companies, their bottoms were painted with antifouling paint that was at best satin. Even today if you walk through any marina in the autumn and winter, you'll find plenty of boats with dead flat antifouling bottoms. You were actually just about right when you first sanded the bottom and could have left it there. Smaller trailerable boats may have had non-antifouling glossy bottoms, but never big cruisers.
@modellingmisadventures
10 ай бұрын
Interesting 🤔
@thediscoman20016 ай бұрын
i was wondering how you would havbe done the windoows mod but to be fair it went better than i though, just a though y did u not make it so it camre from inside the boat to the outside becasue u could have put a flange on the inside to make it fit flush and would have fit better, but what do i know im only a 3d printer guy, but over all im impressed
@modellingmisadventures
6 ай бұрын
👍
@imbranjamil4994Ай бұрын
Cantik brad kapal nya ni k
@martinkormos8191Ай бұрын
Hello, my name is Martin. Your videos are particularly helpful for me. I'm building the Victoria but I'd like to change a few things. Is it possible to get the STL file for the additional portholes? Or the dimensions? I would be very grateful! Kind regards, Martin
@BlandDeuce Жыл бұрын
Could a brush on gelcoat make the process easier to sand also hide the inner structure before paint..may also give you a super smooth surface to lay paint..Looks amazing
@modellingmisadventures
Жыл бұрын
Not sure what a gel coat is.
@BlandDeuce
Жыл бұрын
@Modelling Misadventures it is the underlying coating on boats before paint. Cures really slick. Bush on type is fairly inexpensive from someone like Total Boat. Goes a long way
@ellesmerewildwood4858 Жыл бұрын
Am I missing something here ? I was waiting for the end of the FAB 1 series and this is the 3rd part in this series. Am I not getting notifications ? I'll have to check the playlist. Anyway...Came out fantastic in the end after all that work. In fact, the finish probably looks better than the real boat does. Did you know you can airbrush the Molotow chrome paint ? It's quite delicate though, so probably the chrome spray paint will yield a hardier finish.
@modellingmisadventures
Жыл бұрын
I always have more than one project on the go at once so the videos go up at different stages. FAB 1 is still ongoing!
@ellesmerewildwood4858
Жыл бұрын
@@modellingmisadventures Since I only joined the channel recently, I just had a look at your playlist and geez, I don't know where to start. I see what you mean about having a several projects going at once.
@modellingmisadventures
Жыл бұрын
@@ellesmerewildwood4858 Only four at the moment! The bus should be finished soon but the boat, FAB 1 and the Morris Marina van all need more work.
@HappyDude1 Жыл бұрын
I think its better to paint a boat with a brush like they do with wooden boats
@modellingmisadventures
Жыл бұрын
I’ll probably do that for the superstructure but I didn’t want brush strokes on the hill.
@HappyDude1
Жыл бұрын
@@modellingmisadventures It looks more realistic like that with a good brush and quality paint you wont really see it i did on my rc tanks 😀 the paint is a lot stronger to 😊 and its so relaxing to do inside with some music 😘
@TinyHouseHomestead Жыл бұрын
Put some TARPEEDEES.on it! 😱😝😁🤪🤣👍👍🇺🇲
@modellingmisadventures
Жыл бұрын
Not going to happen!
@romanpastorik22898 ай бұрын
Peter your videos are very nice. Would you be willing to provide the STL data for the windows? I received the same kit this week. Thanks
@modellingmisadventures
8 ай бұрын
I’d be happy to send you the STLs for the portholes. Where will I send them to?
@romanpastorik2289
8 ай бұрын
@@modellingmisadventures info () ModelBoats - sk
@romanpastorik2289
8 ай бұрын
Peter, thank you for your reply and I will look forward to it. I will definitely send you a link to our website when I build it. My email is lower.
@michaelgrimes8828 Жыл бұрын
Is it really necessary to put the finishing polish as the last coat???
Пікірлер: 42
Excellent! The white and red really pops!
@modellingmisadventures
Жыл бұрын
Thanks very much. I like those colours too.
Well done Peter, looks great.
@modellingmisadventures
Жыл бұрын
Thanks 👍
That looks great! Thanks for sharing.
@modellingmisadventures
11 ай бұрын
Thanks very much. Check out the later videos to see where things are up to.
Looking great
@modellingmisadventures
Жыл бұрын
Thanks very much.
Looking good. I use finishing resin inside the hull and on the exterior to seal from water and once sanded smooth fills in all gaps, seams and cracks for paint.
@modellingmisadventures
7 ай бұрын
A lot of boat modellers do that but I built this one as the instructions as said.
Very cool!
@modellingmisadventures
Жыл бұрын
Thanks 👍
Nice boat !
@modellingmisadventures
3 ай бұрын
Thanks!
I think port holes would be beter filled by sticking it on a bit of resin tape then filling the glass area with a bit of clear UV set resin and hardening with the little torch
So that you know, when Chris Craft delivered new boats, they painted their hull sides with fairly gloss enamel, but like most companies, their bottoms were painted with antifouling paint that was at best satin. Even today if you walk through any marina in the autumn and winter, you'll find plenty of boats with dead flat antifouling bottoms. You were actually just about right when you first sanded the bottom and could have left it there. Smaller trailerable boats may have had non-antifouling glossy bottoms, but never big cruisers.
@modellingmisadventures
10 ай бұрын
Interesting 🤔
i was wondering how you would havbe done the windoows mod but to be fair it went better than i though, just a though y did u not make it so it camre from inside the boat to the outside becasue u could have put a flange on the inside to make it fit flush and would have fit better, but what do i know im only a 3d printer guy, but over all im impressed
@modellingmisadventures
6 ай бұрын
👍
Cantik brad kapal nya ni k
Hello, my name is Martin. Your videos are particularly helpful for me. I'm building the Victoria but I'd like to change a few things. Is it possible to get the STL file for the additional portholes? Or the dimensions? I would be very grateful! Kind regards, Martin
Could a brush on gelcoat make the process easier to sand also hide the inner structure before paint..may also give you a super smooth surface to lay paint..Looks amazing
@modellingmisadventures
Жыл бұрын
Not sure what a gel coat is.
@BlandDeuce
Жыл бұрын
@Modelling Misadventures it is the underlying coating on boats before paint. Cures really slick. Bush on type is fairly inexpensive from someone like Total Boat. Goes a long way
Am I missing something here ? I was waiting for the end of the FAB 1 series and this is the 3rd part in this series. Am I not getting notifications ? I'll have to check the playlist. Anyway...Came out fantastic in the end after all that work. In fact, the finish probably looks better than the real boat does. Did you know you can airbrush the Molotow chrome paint ? It's quite delicate though, so probably the chrome spray paint will yield a hardier finish.
@modellingmisadventures
Жыл бұрын
I always have more than one project on the go at once so the videos go up at different stages. FAB 1 is still ongoing!
@ellesmerewildwood4858
Жыл бұрын
@@modellingmisadventures Since I only joined the channel recently, I just had a look at your playlist and geez, I don't know where to start. I see what you mean about having a several projects going at once.
@modellingmisadventures
Жыл бұрын
@@ellesmerewildwood4858 Only four at the moment! The bus should be finished soon but the boat, FAB 1 and the Morris Marina van all need more work.
I think its better to paint a boat with a brush like they do with wooden boats
@modellingmisadventures
Жыл бұрын
I’ll probably do that for the superstructure but I didn’t want brush strokes on the hill.
@HappyDude1
Жыл бұрын
@@modellingmisadventures It looks more realistic like that with a good brush and quality paint you wont really see it i did on my rc tanks 😀 the paint is a lot stronger to 😊 and its so relaxing to do inside with some music 😘
Put some TARPEEDEES.on it! 😱😝😁🤪🤣👍👍🇺🇲
@modellingmisadventures
Жыл бұрын
Not going to happen!
Peter your videos are very nice. Would you be willing to provide the STL data for the windows? I received the same kit this week. Thanks
@modellingmisadventures
8 ай бұрын
I’d be happy to send you the STLs for the portholes. Where will I send them to?
@romanpastorik2289
8 ай бұрын
@@modellingmisadventures info () ModelBoats - sk
@romanpastorik2289
8 ай бұрын
Peter, thank you for your reply and I will look forward to it. I will definitely send you a link to our website when I build it. My email is lower.
Is it really necessary to put the finishing polish as the last coat???
@modellingmisadventures
Жыл бұрын
It was on mine to make it smooth and shiny.
@michaelgrimes8828
Жыл бұрын
Ok, thanks
Oh dear dope is very aggressive to other paints .
@modellingmisadventures
3 ай бұрын
Yes, it is!