One of the best videos ever. Right to the point without a 30 minute introduction.😊 Great.

@JLPicard440

Жыл бұрын

Wow, thanks!

@kebo57

11 ай бұрын

Even better, no country music or whatever!! Just good explanations, to the point.

@JLPicard440

11 ай бұрын

Thank you! I have music in a couple of my videos, but mostly not... 😀

Well done video. Fairly straightforward without and stupid gimmicks or ads, decent camera work. Overall.... Useful. Good job 👍

@JLPicard440

Жыл бұрын

Thank you so much! 😀

Coincidentally, I just came across your video after rebuilding the carburetor on the same system. Well done sir!!

@JLPicard440

10 ай бұрын

Awesome! Thank you for the great feedback...

Rudy, that video was outstanding........very, very well done!

@JLPicard440

3 ай бұрын

Thank you kindly! I really appreciate it... 😊

Wow. That's a thorough explanation and it has great video footage. It will help me to do my carburetor, I'm anxious to try. Thank you so much.

@JLPicard440

Жыл бұрын

Thank you and you're welcome! I'm glad you found it helpful.. 😀

Outstanding work. Thank you for putting this together.

@JLPicard440

2 ай бұрын

Much appreciated! You're welcome!

VERY helpful, Thanx. Nice fix slotting the cover bolt holes.

@JLPicard440

Жыл бұрын

Awesome! Thank you and you're welcome... 😀

Glad i found this video, im lost in the woods right now trying to troubleshoot my troybuilt 42 inch pony. Im pretty sure its a carburetor problem, but there is so much cheap safty crap on it ill never be sure until i finally get the beast running again. I really wish you didn't fast foward thru putting yours back together but thanks again for the help.

@JLPicard440

Ай бұрын

HI Stratcat! I appreciate the input about the fast forward. Sometimes I do that to keep the video from getting to long, but then there's peeps who want to see the full process when it goes back together....

Hey man, this video got me fixed up! Great instructions and info. By the way, I used Stella brush bristles for the clean out wire. Worked great. Thanks.

@JLPicard440

3 ай бұрын

Thanks for the great feedback! I'm so glad I could help.. Thanks for the tip on the bristles.. 😊

@brianoberhausen5153

3 ай бұрын

@@JLPicard440 I also wanted to tell you that my emulsion tube was really jammed in there. I couldn’t push it past the opening in the barrel. My solution was to feed bailing wire through it, just double the fed- end over, wrap the long end on a rack post and quick tug about 3 times to free it. Just in case that helps anyone else.

@JLPicard440

3 ай бұрын

Thanks for the feedback! I'm sure it'll help someone.. 😊

Sweet vid! Thanks So I’m doing a tune up/trying to correct surging but @8:00 you say the main jet doesn’t always thread out to get at the emulsion tube. Mine will not and I’m afraid to damage it. I guess I’ll bypass it for now but I’d really like to correct the surging, any ideas?

@JLPicard440

2 жыл бұрын

Yes the surging may be caused by the low speed jet. I don't remember exactly where it is on this one, but those little holes inside the Venturi are usually part of that circuit. If you google "low speed jet surging" something should come up about what I mean. I hope that helps.. There are other things that could cause it, but I've found that to be most common.

@whattha930

2 жыл бұрын

@@JLPicard440 Excellent, I’ll have a look, thanks for the reply!

@JLPicard440

2 жыл бұрын

YW

I washed my 2017 17.5hp Troy-Bilt Pony riding mower and now having issues with flooding and fuel coming out of muffler!! I noticed wires are missing from fuel solenoid!! I found a white wire, but think there should also be a black! How is this part wired to the mower?

@JLPicard440

2 ай бұрын

HI, you might have pulled something loose. I'd have to see it to see where the wires go/ went.

What type of blade works best cutting out the slots on the motor cover ? TY

@JLPicard440

2 ай бұрын

A Dremel with a metal cut off wheel would work great....

I hope so I need to fix mine 🤯 replaced fuel pump but now I think it’s the carb won’t run on full choke now. Never will run on anything but full choke HELPPP

@JLPicard440

9 ай бұрын

Yes it sounds like a carb problem.... Have you taken it apart to clean?

I have a Troy-Bilt 17.5 what are brand new plug in it I took the muffler off it runs like crap it'll stay running the one I throttle it up it runs really bad the whole lawn mower shakes

@JLPicard440

Ай бұрын

Hi,... Does it run bad if you put the muffler back on?

What are the intake and exhaust valve settings on this engine please?

@JLPicard440

6 ай бұрын

I think it's .004 intake .006 exhaust, but you might want to double check ..

Where does tiny o-ring go? Found after disassembling and can't figure out where it goes.

@JLPicard440

3 ай бұрын

HI! Without seeing it I can't be sure. Sometimes there an o-ring on the needle valve for the idle, sometimes there's on o-ring on the emulsion tube, but I don't think this one uses one... It doesn't go on the bottom of the bowl bolt does it? Usually that's a flat gasket.

@rl96ss

3 ай бұрын

@JLPicard440 Hello! Not sure but hadn't taken emulsion tube out yet and the one on fuel solenoid is definitely flat. Looked up the diagram and couldn't see a small o ring in the blow up, so have no idea? Thanks for responding

@rl96ss

3 ай бұрын

I'm thinking needle valve but don't see how it would go on.

@JLPicard440

3 ай бұрын

I don't remember if there's any close-ups in this video that might identify where that might go? I'd have to go through the whole thing to see. If you have access to Facebook you can upload a picture to my "Take a Bath Productions" page and I'll take a look and see if I see anything.

@rl96ss

3 ай бұрын

@@JLPicard440 Appreciate the help.

Nice explanation taking it apart but didn't like the putting it back together.

@JLPicard440

Ай бұрын

Thanks for the great feedback! I'll keep that in mind. ..

Why not just remove carb and intake manifold but leave the flywheel cover on?

@JLPicard440

Ай бұрын

I think on this one you can do that...

Could you share the engine number please?

@JLPicard440

Жыл бұрын

Hello, I don't have access to this mower anymore...

You took off the top of the engine housing but did not show the complexity of putting it back in place. Two spacers fell out when I removed it and I have no idea where to put them. I put the top back without them and destroyed the fins or restart. Also, I could not refit the air filter so I knew something was amiss. AJC

@JLPicard440

Жыл бұрын

HI, sometimes I don't show how it goes back because it goes together exactly the same way it came apart. It''s 5 bolts and a plastic clip. I reviewed the video and there are no spacers involved in taking that off.