Thank you! Just cleaned out my carb on Honda 160 engine. Did exactly what you showed in the video and she started right up. You saved me at least 200 bucks!!

@-DIYPRO-

3 жыл бұрын

Glad it helped

@tim5111

2 жыл бұрын

Thats amazing! I just recieved a plate compactor with a gx160 honda engine. Got it on the cheap because they couldn't start it. Im going to give this a try for sure. Fingers crossed.

@coatneyadkins9005

Күн бұрын

You would've paid two hundred to get your small engine started?? Is that an average small engine shop bill?? If so... I'm changing shops lol

Thank you for this very helpful video... I had the same carburettor problem and it's solved now.

@-DIYPRO-

2 жыл бұрын

Awesome, glad it helped.

The choke(white) lever can be removed & the round pin on it placed in the end of fuel line. Instead of crimping the fuel line

MegaFlaxman I hope I can get a response on this question. I have a 2008 Honda clone 6.5 horizontal shaft. It was in the original box till just recently when I aquired it. I filled with oil and gas and wouldn’t start. I checked the compression and it’s 28 psi. Checked the rockers and they’re moving like they should. I removed the rockers and physically moved the valves up and down, both seem to be seating properly. Filled cylinder with oil and tried again, still 28 psi. What’s my next move, remove the head and check the valves?

I learned two things on my last Briggs carb clean and diagnosis: When i removed spark plug and pushed possible air/fuel out of cylinder, i cleaned lightly with my starting fluid. When i tested for spark... it lit my light spray off fluid. Hard for my eyes to look for spark... but easy to see a 2 second fire! (I will actually purposely use this method in the future!). Secondly, my single bottom bolt to the carb bowl supplies the main jet! I used my torch tip cleaner kit, dupray, and comoresser air... she fitted right up! Fresh gas, a bit of mystery oil... and my freebee pressure washer is on its way for use!

@-DIYPRO-

Жыл бұрын

Right on!

Thank you 😊 my engine is now going after watching this video the tiny hole in the jet in the carb was blocked very hard to see but I used a bristle from a wire brush to poke clean the engine started straight away also did not have to take apart as much just take 2 bolts of at the cup then use small flat head to unscrew the brass jet used a wire brush bristle to clean it engine going in 10 minutes 😀 👍

thank you for your video but i have a honda 160 air compressor stopped working i changed the carburetor, spark plug, And it does not turn on, could you tell me that it continues to check

Thanks a a million 'I done most of this 'it was full of gunk 'but I didn't clean that little brass valve 'I will do now Thanks again ❤

Yay I finally got me engine fix for my go kart it was the choke it was dirty so I had to clean it!!

Great video. Thank you for sharing your knowledge.

@-DIYPRO-

3 жыл бұрын

Anytime!

Thank you very, much, your Video has helped me a lot, just checked with the spark plug, it's on! Be Blessed hundred times

@-DIYPRO-

6 күн бұрын

Right on!

Great video i threw some gas in the hole and yanked a couple times and fired up , gonna clean the carburetor Tomorrow

@-DIYPRO-

3 жыл бұрын

Let us know how it goes.

Thanks so much for this beautifully explained and informative video...

@-DIYPRO-

2 жыл бұрын

Glad it was helpful!

@siphelofeni6112

2 жыл бұрын

My Honda generater , don't have power when I put Airfilter it need me to keep out Airfilter to have power,I cleaned the cuburater already

@siphelofeni6112

2 жыл бұрын

@@-DIYPRO- I need help sir my Honda generater need me to keep out Airfilter to have power,if I bring Airfilter back it's don't have power,I already cleaned the cuburater

Thanks bud, nice one. I had to rewatch it lol i remember watching it long time ago. Cheers was great help

Thanks so much very helpful video excellent explanation Awesome

@-DIYPRO-

3 жыл бұрын

Glad it was helpful!

What if it doesn’t run after spraying carb cleaner in the carb? My 240x on my trash pump won’t run. I sprayed carb cleaner and nothing. It has spark. But won’t run. I put fresh gas in it, new plug, and sprayed carb cleaner down in carb. Still won’t run.

Very helpfull video. What kind and size of screwdriver did you use to unscrew the nozzle?

@-DIYPRO-

2 жыл бұрын

Small! Not sure what size it is, doesn't have any markings on it.

I change my carburetor and coil for my water pump. It will crank and show signs of starting but will not start. Should I check the valve clearance and compression

@-DIYPRO-

4 жыл бұрын

Do you have spark?

Me gusta esta video mucho gracias par todo information! need pero olvidaste mencionar que revisaras el tanque de gasolina en busca de residues y filtro de gasolina GRACIAS

There is another needle jet above the small jet you screwed off, it sometimes falks out or you tap the sides and it comes out

@-DIYPRO-

2 жыл бұрын

Good point!

Thanks mate, you just fixed my generator.

@-DIYPRO-

Жыл бұрын

No problem 👍

I have a greyhound 6.5 it’s similar to those engines. All it needed was a pitcock for the gas tank. Started up and ran beautifully when we poured gas in the carb without the gas tank. Now we got the gas talk on and tried starting it even after we poured a lil gas in the carb it didn’t want to start at all

@-DIYPRO-

2 жыл бұрын

That's a weird one, did you end up finding out the issue.

@oprxghost4859

2 жыл бұрын

@@-DIYPRO- yes, apparently the throttle was attached straight to the governor ( it’s on a go kart now) so there was no idle setting, the throttle was fully closed. I ended up having to get someone hold the throttle a quarter of the way open while I start it to get it to fire up.

Im getting a gx270 or gx390 and ima do plugs, oil, dirtbike carb and chuck it on a go kart

What if the carb is brand new and it’s still somehow not getting fuel to the engine?

I had a spring on my GX 390 underneath the gas tank that broke. Wouldn’t crank for anything. To the shop it went. On another one I have I bought a 14 dollar carburetor and it ran perfecto.

@juniorcook4094

4 жыл бұрын

Was it the thin spring

@billcoley8520

4 жыл бұрын

junior cook I’m not sure. It was under warranty so I let Northern Tool fix it.

Hi there! For winter storage should the choke be left on the on or off position?

@-DIYPRO-

2 жыл бұрын

Choke doesn't matter. Important part is to either run the carb bowl dry or if you have a fuel cut off switch then turn it off so no fuel goes into the bowl and run it til it shuts off. the killer is ethanol fuel sitting in the bottom of the bowl. It will separate and gum up the ports.

je desirerais voir une video sur un moteur honda thermique gx160une fuite huile au nivaux de axe de la poliez

Hi there great video. Can you please tell me what oil you recommend for these engines? Thanks.

@-DIYPRO-

2 жыл бұрын

I use whatever i am putting in my car that month.

How do I know if it’s something else that’s wrong ????

And what about the air/fuel mixture jet ?? Located under the plastic idle screw, if this is blocked then no starty or at the worst it won’t run clean !!

@-DIYPRO-

2 жыл бұрын

Good catch.

Thank you so much

@-DIYPRO-

2 жыл бұрын

Glad it helped.

This video allowed my gx390 to once again crank up and run. It turned out to be the ignition coil. Quick question - I bought my pressure washer (4k/4gpm - gx390 this engine) and after 2-3 pulls it will crank but it takes a little muscle to pull. The pressure washer pump is removed and I made sure the engine is not vapor locked by changing the oil and also removing spark plug (pulled a few times to rotate it). What would cause the pull to be pretty hard? I know this is a bigger engine but what could it be?

@srdjannakalamic5856

3 жыл бұрын

Need to adjust the values

@joesinakandid528

Жыл бұрын

@@srdjannakalamic5856 While you're doing that check the exhaust valve rocker arm for cracks. Usually the 160 and 190 engines are the bad ones but while into the valves it only takes a second to check.

Does the bowl have to be full (float working) in order to start?

@-DIYPRO-

2 жыл бұрын

No, you can start it with just a little starting fluid in the carb. To keep running, yes the bowl needs to be full.

Excellent video and huge help. Thankyou

@-DIYPRO-

3 жыл бұрын

Glad to hear it!

Good video..i like

@-DIYPRO-

2 жыл бұрын

Thank you! Cheers!

Other than cleaning your carburetor and you’re still not getting fluid how do know , when to just swap out carburetor with new one?

@-DIYPRO-

2 жыл бұрын

If you test it out with some starting fluid and it starts up then dies then you know for sure its the carb and you can replace it. If you shoot carb fluid into the carb and it still doesn't start then it's something else. Check spark plug, check oil level (some small engines have oil level sensors that cut the engine out if low oil)

Thanks guy,

@-DIYPRO-

2 жыл бұрын

Hope it helped.

Thank you so so so soooooo much

@-DIYPRO-

4 жыл бұрын

Hope it helped ya.

@45tv8

4 жыл бұрын

@@-DIYPRO- yes

how would you go about inspecting a honda gx390 before purchasing it off craigslist

@-DIYPRO-

3 жыл бұрын

Does it run? If not then low ball the price until you feel comfortable knowing you might have to put a lot of work into it. If it runs then how does it sound? Check the oil, if tar then you know they haven't done anything to it maintenance wise. If clean then you know they tried to take care of it.

@mattwardlow3233

3 жыл бұрын

@@-DIYPRO- I found a gx390 listed for 400$ if it doesn’t run well how much $ could it cost getting it to work

Thank you!!!!!

@-DIYPRO-

3 жыл бұрын

No problem

Couldn't tell from this video, does the plug need to be grounded against metal chassis to spark ? What do we do if there is no spark ?

@-DIYPRO-

21 күн бұрын

Yes, I usually just rest on or next to the engine block.

@SmeeUncleJoe

21 күн бұрын

@@-DIYPRO- I finally figured out why my hole auger wouldn't start: I did not get the torque bar with it and that closes a kill switch near the engine when installed. Took me a day of research. These things are really dangerous and I emphatically suggest no one get one if they think it's a one man tool. It takes 2 big guys to use. i realize that's a little off topic as this vid is for motor only. Carry on.

forgot to clean the emulsifier jets... He had the, main out it was right there???

UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzread.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.

@-DIYPRO-

11 ай бұрын

The Hondas will last forever.

My carb got gummed up. Mine, an older 6.5, carb gaskets were definitely not ethanol friendly. The gaskets swoll and broke down clogging the jets.when I took of the bowl there was a goo of melted black gasket and gas slime. I had been running it every day for about a month. Took a weeks vacation. Didn’t drain the bowl. Came back and It wouldn’t start.

@-DIYPRO-

2 жыл бұрын

Been there!

10:33: Looks like you got a little helper there.

@-DIYPRO-

Жыл бұрын

Yes. Problem is he can't ever remember where he put my tools!

Wowwwwww thanks you si much

I have the same engine I can't understand why it doesn't start, it has compression, it sparkles, I cleaned the carburetor but nothing, even putting gasoline directly into the cylinder it doesn't start, what could it be?

@-DIYPRO-

2 жыл бұрын

Mine is currently covered in snow or else I'd go double check but I'm pretty sure these have a low oil sensor. That would be my next check. Double check that it has oil and that it's level. I say that because I had a tiller once that tilted the engine slightly and so even though it was full on the one end it was actually low on the senor side and would always shut off.

What if I take off the float bowl on Honda GX 120 and its only has drops of gas inside?...Thats my issue.

@-DIYPRO-

4 ай бұрын

Then fuel is not getting into the bowl. With the bowl off see if the float is opening and closing (it's the plastic donut looking thing). It should hang down and be letting gas enter. Then if you push it up it should close off. Those get stuck closed and open all the time. I wish I could post picture in comments to show. Hopefully that makes sense.

@stinkletoes8285

4 ай бұрын

@@-DIYPRO-Yes...needle valve with spring?...I am going to remove that and clean it up..also remove jet and clean...The bowl itself is super clean...no residue-coloring etc..like you said hopefully its just that needle valve thingy..

What do you think would be the problem if it’s leaking a lot of oil

@-DIYPRO-

2 жыл бұрын

I guess it depends on where it's leaking from, the case, from a seal, out of the carburetor?

@leaflux_gaming5668

2 жыл бұрын

@@-DIYPRO- I opened it up and the carburetor was covered in oil and were the air filter sits was also covered in oil. Then my brother found out that a rocker arm was broken in it

So what if you have a honda 5.5 with less than an hournon it valves lashed properly has plenty of spark plenty of fuel going into cylinder and plenty of air and will not fire at all pops and that's it thank-you!

@-DIYPRO-

Жыл бұрын

If the lash is correct and you are getting spark then it's probably the timing.

Air stew fuel stew how many turns on each 1

@ColinMorehouse-yh3uq

Ай бұрын

I mean screw

Does WD-40 work for cleaner?

@-DIYPRO-

Жыл бұрын

No. Brake cleaner and carb cleaner are fast drying solvents. WD won't dry up and will actually start collecting dirt and clog it even more.

What if you use starter fluid but the engine doesn’t want to start at all.

@-DIYPRO-

5 жыл бұрын

Do you have spark?

@whistlershootingadventures3819

4 жыл бұрын

@@-DIYPRO- I was going to ask the same thing. Yes, I have spark. Won't run even after squirting starter fluid in the air intake. Just a cough and that's it. Thanks

@peedsii1991

3 жыл бұрын

@@whistlershootingadventures3819 Hello. I was wondering did you ever find out what the problem as, and how you fix it ?? ( i have the same problem ) Thank you for help or reply in advance.

@whistlershootingadventures3819

3 жыл бұрын

@@peedsii1991 It was a pressure washer and the problem was obstructed water flow. Easy to fix.

Nice video..but did it work?? Lol I was waiting on him to turn it back on

@-DIYPRO-

3 жыл бұрын

I should have shown it on my go kart ripping around the yard. Yes it runs great!

HMMmmm - Didn't you think that the sediment bowl on the carb needed to be looked at?

@-DIYPRO-

Жыл бұрын

That wasn't the carb from that engine. For sure if there is sediment in the bowl then it needs to be cleaned out.

If someone put diesel in Honda gx390?????

@-DIYPRO-

3 жыл бұрын

Did i miss something? Where does it talk about diesel in a Honda?

Also at some mini cars.

Ok I have a 390 with key start,cleaned carb,have spark,will not crank even with starter fluid also has fresh gas and oil..what could it be

@-DIYPRO-

4 жыл бұрын

Lots of them have low oil sensors and so if there is not enough then it won't start. Try putting a little more oil in it.

@juniorcook4094

4 жыл бұрын

Ok will do. Thanks

@juniorcook4094

4 жыл бұрын

Done that still nothing,i know the head gasket is blowed out,I'm not sure how long they ran the motor with the bad head gasket,it has no compression

@-DIYPRO-

4 жыл бұрын

@@juniorcook4094 yea that would make it not start!

@juniorcook4094

4 жыл бұрын

@@-DIYPRO- I changed out the head gasket and still won't crank and no compression,valves set right..last thing I know is changing the piston

I thought my phone was broken but there was just no sound

I followed the instruction , my Honda pressure washer started right away )))

@-DIYPRO-

3 жыл бұрын

Awesome!

If your engine is hard to pull, then your compression release on your camshaft is broken

@-DIYPRO-

2 жыл бұрын

That repair will take a little more time!

Or if u dont wanna do all that carburetor stuff u can just buy a new one for like 20-30 dollars on ebay

@-DIYPRO-

3 жыл бұрын

Done that a couple times.

@levagabond9489

2 жыл бұрын

It's a way more satisfying to repair stuff. You lurn and you recycle. Good for you and the nature.

@user-lm9sf6le5n

Жыл бұрын

❤❤

Okay I’ve done the vavles regap n check the rods one wasn’t conntrd fixed that check for gas carb was leakin early fixed that as well check spark it’s there fuel going to the carb not the engine so guessing carb clean which only thing I haven’t done ran at the trailer when threw gas down the carb carb spray start didn’t work but gas did Um so gonna clean the carb n let ya know how to goes just annoying didn’t seals new cams everything just to be like no spark at all lol gets spark just no fuel

@-DIYPRO-

2 жыл бұрын

Did you end up cleaning the carb? Did it work?

@905mudboysdc4

2 жыл бұрын

@@-DIYPRO- not yet I’m try to that tonight if I get the time I ordered a new one anyways cause the left side bolt hole shoulder is broken n fuel screw is bent so may not work lol

@905mudboysdc4

2 жыл бұрын

@@-DIYPRO- gonna try it anyways just to see I’ll keep ya posted boss man

@905mudboysdc4

2 жыл бұрын

@@-DIYPRO- nah cleaned the carb didn’t do anything timing was off by the smallest bit out the old carb back on leaked like crazy put the new one on still leaked took that plastic spacer out stop leakin lol engine runs ok it’s a cruiser for sure no top speed at all a 12 year old be comfy with the speed lol gonna go out buy new engine this weekend lookin at a 420 with electric start to swap into it or lookin at a 190cc semi 5 speed kit to throw into it just thinkin on which way to go atm engine that’s in the mini bike smokes like crazy thought it was the two stroke mixed gas buddie ran in it before it was parked but nah ran it 7 times now easy 20 mins each didn’t burn it off check oil the oil I use it great I find just think the seals on top end need to be done now already did the bottom end so might as well rebuild it with the stage 3 kit for the cams atm wish I didn’t sell my first bike ran great had a Hemi on a doodlebug miss it buddie wants 150 more then I sold him it n it’s damaged to hell lol

Why do you sound like this old tony ? If I’m honest I’d say this is defo this old tony

@-DIYPRO-

2 жыл бұрын

I don't hear it but you not the first to tell me that so I guess I sound a little like him.

@siphelofeni6112

2 жыл бұрын

@@-DIYPRO- I need help my Honda generater don't have power when I put Airfilter,it need to work without air filter

@siphelofeni6112

2 жыл бұрын

I already cleaned cuburater

Once again, you failed to check the level and condition of the oil before attempting to start the engine.

@-DIYPRO-

Жыл бұрын

Agreed, Honda does put an oil level sensor on there and it won't start if too low.

No spark

@-DIYPRO-

Жыл бұрын

Check the wire, and ignition coil.

@-DIYPRO-

Жыл бұрын

Also the spark plug of course.

Mobaile number moklo

dont crack the block

honda✔

@-DIYPRO-

2 жыл бұрын

Double check!

I wasn’t soo lucky. Mine’s going to the shop. First it’s going to get a new carburetor & second a battery powered electric start. Why the fucknuts had a pull start is absolutely stupid! Ethanol fuel only ruins carburetors. I’m not going to try your repairs. I know what the shop will say before dropping it off.

@-DIYPRO-

2 жыл бұрын

I ended up putting an electric start on this one as well, so much better.

To much waffle

We know where small engines are used. You don't need to tell us. Sigh.

@-DIYPRO-

3 жыл бұрын

You'd be surprised. My 4 year old didn't know that!