Brake Disc Renewal - Toyota Yaris (Brake Rotors)
Автокөліктер мен көлік құралдары
How to remove and replace the front brake discs (rotors) on a 1999 to 2005 Toyota Yaris 1.0 petrol. It is recommended that if you are fitting a brand new set of brake discs, you should replace the old pads with new ones at the same time. Also, if you are fitting new discs, before you install them, use brake cleaner and a cloth to wipe off the rust protection coating from both sides of the discs.
Torque settings:
Caliper Bracket Bolts: 88 Nm (65 foot pounds)
Caliper Bolts: 34 Nm (25 foot pounds)
Thanks for watching. Please comment, like and subscribe !.
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2022
Read important information below:
Disclaimer:
Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Screwsnutsandbolts recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.
Пікірлер: 30
Thank you so much. Sweden.
@screwsnutsandbolts
3 ай бұрын
Thanks for watching !
clear, simple, concise and NO SILLY ROCK LOUD MUSIC!! Keep em coming!
@screwsnutsandbolts
Жыл бұрын
Thanks for watching ! 👍
Legend! Finished the job thanks to the top tip regarding the bolts to un-seize the rotor!!
@screwsnutsandbolts
Жыл бұрын
Nice work! :)
Very simple easy to watch , thank you man
@screwsnutsandbolts
2 жыл бұрын
Thank you very much !
If you have more please share them.
Awesome video - Like it that you just type out what to do and the bolt sizes you used!
@screwsnutsandbolts
Жыл бұрын
Thanks 👍
Excellent tutorial,Nicely done mate.👌👌👌
@screwsnutsandbolts
Жыл бұрын
Thanks for watching ! 👍
This channel is so concise and awesome !
@screwsnutsandbolts
10 ай бұрын
Thank you !
Nice clear process, thankyou for the video. Whilst dismantled, I'd clean up the caliper assembly and bolts too, with some copper slip for good measure. And may I be so cheeky as to suggest an apostrophe at 7'10" ?
Thanks !
@screwsnutsandbolts
4 жыл бұрын
No problem!
Excellent helpful G b u. 👍👍
@screwsnutsandbolts
Жыл бұрын
Thank you !
Great thorough video, any idea what torque the 17mm bracket bolts and 14mm caliper assembly bolts should be? You said to just tighten. Thanks for the video!
@screwsnutsandbolts
Жыл бұрын
Thank you, the torque values are actually in the video description 👍
@In_Beta
Жыл бұрын
Oh Great! Thank you so much!
@screwsnutsandbolts
Жыл бұрын
@@In_Beta You're very welcome :)
Great video clear and concise step by step,asalways.Is it ok to use copper grease to lubricate the guide pins,or should I use HMP grease ?Look forward to next video.
@screwsnutsandbolts
4 жыл бұрын
Thanks very much. No I don't think copper grease can be used or multipurpose grease. I think it needs to be a silicone base grease as far as I know.
Yr video bol kr benaya kro
.good.. Toyota Yaris caliber itself fits the Toyota Eco?
@screwsnutsandbolts
2 жыл бұрын
I don't know, sorry.
What about greasing the caliper pins?