Thanks for showing how to open one of these. I'm using one of these for registering designs while screen printing. Needed to have it mounted to a ceiling pointed straight down without setting off the blinking off level feature. Was able to wedge a small piece of folded paper in between the laser pendulum and the magnet below it and it disables the blinking. If I ever need to use it as a level again I can just take it apart easily and remove the paper. Thanks again.

@fixed-gp4wt

3 ай бұрын

Thank you

I'd also like to thank you for this video! my Bosch GLL2-10 stopped wasn't working when I pulled it out of the cabinet to use, so I watched your video and it gave me the confidence to disassemble my laser level. mine was a bit easier to take apart, it is held with 5 screws; it turned out to be the on/off switch, I sprayed it with some electronic component cleaner and put a bit of dielectric grease in it and now it works perfectly.

@fixed-gp4wt

2 жыл бұрын

Thank You 🙏 so glad I could help you

Thanks for your video. I've got a BOSCH Quigo laser. After a fall from 1 meter high it stoped working and the front cover was a little misaligned. I had no clue about how to disassemble and it turn out that it was exactly as the model you showed. Now it's fixed. Thank you very much.

@fixed-gp4wt

2 жыл бұрын

Glad I could help 👊

Thanks for responding. We contacted BOSCH for assistance but they couldn't help.

@fixed-gp4wt

2 жыл бұрын

Sorry to hear that

I've been waiting for discount on a decent brand laser level, just found this today on Amazon at $38. What I didn't like from it is that you can't manually lock the laser for inclined/diagonal arbitrary setups. When it arrives I'll disassemble it and separate the mechanical lock from the electronic turn on switch, use that switch for it to bypass the inclination limit sensor, so it doesn't flash when it's on manual locked mode, and put an independant power switch. Maybe I'll replace the laser module with a higher power, and I think it'll have the functions of a more expensive model, specially with that super cheap price. Thank you for sharing!

I have another model; same construction. Thanks.

@fixed-gp4wt

2 жыл бұрын

You’re welcome

I've got the same level and it is really dim. I can see the light but it doesn't cast them at all. I changed the batteries with no improvement. Hooked it up to a lab power supply at 4.5 volts and it gets better. I'm thinking I've got resistance in the switch or terminals. Thanks for showing how to crack the case open.

@fixed-gp4wt

9 ай бұрын

Thank you, I’m happy that it helped you

Have you disassembled such a laser, but only a laser from an aluminum housing (hrinzotal) in what way? Thanks in advance

@fixed-gp4wt

2 жыл бұрын

I don’t think so

Where to order such a replacement laser horizontally?

Where can we obtain repair services for the BOSCH GLM 80? We are having problems with the LCD Display Panel. Also, when the Unit is not connected to the Charger it turns ON and beeps without anyone operating the ON/OFF Function.

@fixed-gp4wt

2 жыл бұрын

You can try Bosch, I’m not sure Thanks

Makes you 50/50 happy

Hey I need to replace the lens on my GLL 100 G any advice?

@fixed-gp4wt

2 жыл бұрын

Honestly, I don’t know

We'll just have to look around elsewhere for a new or good used Display. Thanks

Hi, Do you know how to calibrate gll3-330cg. Thanks

@fixed-gp4wt

Жыл бұрын

I’m sorry, no I don’t

Cool. Can you tell me why my laser level wont stop blinking? It's a Bosch GPL3

@chronicreview3538

4 жыл бұрын

It's either not leveling or something on the board has failed. It's hard to tell without seeing it. Thank you

@tl9819

4 жыл бұрын

its out of calibration or the pendulum needs adjustment

@JorgeGonzalez-go3xp

3 жыл бұрын

I have a bosch 150gl eck. I left it out and got wet now what do you recommend I do to fix it. The small lens are foggy but ide appreciate any imput