Boring, Honing, Fitting Pistons, Willys L Head Engine
Тәжірибелік нұсқаулар және стиль
In this video I will show how to set up the Van Norman Boring Bar, bore the block, hone, and hand fit pistons. This Willys L Head engine will be getting Silvolite Pistons and I will show you how to achieve a plateau finish on the cylinder for best performance.
Пікірлер: 37
Thanks Brian, happy to see another video from you. No idea you were battling a hurricane. Stay safe my friend.
@metalshaperJeep
4 жыл бұрын
Hurricane is past and I am back in the shop making videos. Had to run the house with the generator so shop was dark. Guess I better get busy getting the detroit diesel 3 phase generator up and running so I can power the entire workshop. Thanks for watching.
Another excellent video. Loads of information and some great tips. Never heard of a plateau brush, I always learn something from your videos!! Glad to hear you weathered the storm.
@metalshaperJeep
4 жыл бұрын
I give tips when the occasion presents itself. The plateau brush is the best step you can take to final prep your cylinder for the piston. Glad to have long time viewers like yourself who enjoy the videos. Thanks for the support.
Brian, Thank-you so much for this explanation of how to bore a cylinder. I've wondered for years, and you did a great job clearly explaining it. You really are helping a lot of people, whether you realize it or not. Like is so often the case with school teachers, you don't often get thanked, but your work is important, and quietly appreciated.
@metalshaperJeep
4 жыл бұрын
Thanks for the comment Bill. I try to help people and try to keep them from making mistakes. You can't believe the things that show up in my shop. I hope there are some younger folks who learn something from my channel and take off on their own. Brian
That honing machine looks like a life saver, honing by hand is so messy. Glad you guys are ok after the storm. Taker easy, Will
@metalshaperJeep
4 жыл бұрын
honing machine is dialed in perfectly and will save lots of time and mess for sure. Storm made a mess of things and lots of trees still down but lights are back on and I am making progress.
Excellent video Brian, thanks for giving US your time and skills
@metalshaperJeep
4 жыл бұрын
Glad you enjoyed it
Great video brain enjoyed the info on setup!!!!
@metalshaperJeep
4 жыл бұрын
Glad you enjoyed it!
Great video!
@metalshaperJeep
4 жыл бұрын
Glad you enjoyed it
Another great video Brian. I love the wire toilet brush. 🤣 👍🍻
@metalshaperJeep
4 жыл бұрын
That little brush does more than you can imagine. Thanks for watching always good to hear from you.
awesome sir.,great
@metalshaperJeep
4 жыл бұрын
Keep watching
so glad I found your channel. ill be picking up the material to construct my own 1973 tub. I'm having a hard time finding schematics if anyone knows a good place to start looking
Great video Brian! I have a question...do you still use the torque plate when using the honing machine to tension the block?
@metalshaperJeep
4 жыл бұрын
Sometimes
What is the magic trick to removing head studs? My L134 just will not release its hold on them. I got 2 of the 15 out but man even after a two weeks soak in Kroil they wont move. Using a Lisle stud remover (piece of junk) wont remove them. Double nutting fails as the nuts wont lock enough to keep from moving both nuts when turning the lower one counter clockwise. Even tried the candle wax trick by gradually heating the block at the stud base then apply the candle wax. They are stuck. My next attempt will be a MatCo stud remover from the SR202 kit. Any ideas?
@metalshaperJeep
4 жыл бұрын
Don't try to reuse your head studs. Get a big pipe wrench low on the stud and back them out. Drill out the ones that break, and install new studs when reassembling the engine.
Do you rebuild L226's...?
@metalshaperJeep
4 жыл бұрын
yes
Hello master how to make cutting tool point which no grit stone is best bike cylinder honing plse help me
@metalshaperJeep
2 жыл бұрын
not sure what you are trying to do. Standard boring bar can bore motorcycle cylinders .
Which grade cutting tool use cutting
@metalshaperJeep
3 жыл бұрын
carbide insert
You always seem to be working solo, making body panels, body and paint, rebuilding drivetrain and engines... how on earth do you get it all done?
@metalshaperJeep
4 жыл бұрын
It is tough working alone sometimes but I have been doing if for so long it I am used to figuring out how to do things. The biggest thing that was a pain to work on alone was the paint booth. Installing the ridge, setting the rafters, and installing the metal roofing took much longer alone..... but I got it done anyway. Thanks for watching.
Sir would like to know how to get in touch with you I don't have a computer just my phone. I have two jeeps 53 3b and a 49 3a and I know I can't do it all how can I get in touch with you
@metalshaperJeep
3 жыл бұрын
metalshaper@comcast.net Brian
@douglaspiercy3996
3 жыл бұрын
Thanks very much Happy holidays to you and yours
Hi
Brian . To much boreing Barr NOISE CAN'T UNDERSTAND YOU CAN'T YOU TALK WITH OUT THE NOISE 🐤🐤👍
@metalshaperJeep
4 жыл бұрын
OK, will make adjustments on the next video.