100 horsepower in the palm of your hand? Typical Friday night in the Bumblefuck household. Early Access to New Stuff: / ave
Жүктеу.....
Пікірлер: 835
@tjockiskatten6 жыл бұрын
I'm from Sweden and as soon as you popped that open i recognized the parts. I used to harden those. They are plasma nitrated.
@arduinoversusevil2025
6 жыл бұрын
Thanks man!
@tjockiskatten
6 жыл бұрын
AvE No, thank you! It must be about 7 or 8 years since I worked with metal hardening. You just gave me some fond memories.
@PyroShim
6 жыл бұрын
This is why i still use youtube!
@MrPruske
6 жыл бұрын
great info can still be found :)
@Lillebroor
6 жыл бұрын
I worked at Parker too here in Sweden. As a machinist where they produced the hydraulic blocks. =)
@Afraithe6 жыл бұрын
Leakage is cooling, gotcha, it's like I say with my old volvo wheel loader from -79, if it's leaking oil, it's got oil.
@Valtra-rn1ed
6 жыл бұрын
Affra thats what i always say! Start worrying when it stops leaking!
@aPreciousPiggy
6 жыл бұрын
Only way to know if there's oil in it is if there's oil under it.
@perlandstrom5023
6 жыл бұрын
Yeah no need for a dipstick XD
@AndersJackson
6 жыл бұрын
And it is good against rust too.
@mmurola9859
6 жыл бұрын
Someone told me he saw an old Caterpillar wheel loader where instead of the transmission fill plug there was a tap. Each evening the operator would drain several liters of oil from the trans and pour it into the hydraulic tank. He sai "I'll just put it back where it came from". Had a leaking transmission mounted hydraulic pump so the oil came from the hydraulics system. Also heard of a Lännen loader excavator that had a sheet metal pan suspended by chains under it's belly to catch the drips. :)
@Catatonicwater6 жыл бұрын
New mat = another foundry vijayo
@nbrosens6 жыл бұрын
Ah yes! Another AvE vijeo! Dear Bumblefuck, I leave you with a thoughtful poem.. Mary had a little lamb It ran into a pylon. 10,000 volts went up its ass and turned its wool to nylon
@altfseven
6 жыл бұрын
nbrosens Mary had a little lamb He farther shot it dead Now she takes it to her school Between 2 chunks of bread
@steviefordranger198
6 жыл бұрын
LOL, love it.
@timrobinson9192
6 жыл бұрын
Mary had a little pig She couldn't stop it gruntin' Once it got right on her nerves She kicked it's fucking C**t in !
@tyttuut6 жыл бұрын
"It's starting to get a little haggard around the edges." I'd say it's more haggard in the middle, where you poured molten aluminum on it.
@timothybarney7257
6 жыл бұрын
I was thinking that as well...the edge was the only good part left!
@MattsAwesomeStuff6 жыл бұрын
A new self-healing cutting mat? Nooo! I used to be able to tell roughly how old a video was by the condition of its battlescars. Now you've gone and destroyed all that precious chronological metadata. You fool. Hopefully her time away from the main bench lets her plastic nanites work their magic and in a few months we'll see her back in competition form.
@pubcollize
6 жыл бұрын
This one is clearly bigger though. So now we can have an eaven rougher estimation based on which cutting mat is shown. Let them be known as Bigger Cuttingmat and Authentic Deck. AKA B.C and A.D.
@LucasGarrow
6 жыл бұрын
Like being able to tell what season we're in.
@MikeCookie1973
6 жыл бұрын
Go back a bit, and you might find when the previous one was put into service...
@jonathanryals9934
6 жыл бұрын
I'd say one a year is 'bout right.
@tattmanndann
6 жыл бұрын
MikeCookie1973 here i think .kzread.info/dash/bejne/aaSCj8inhcinY9I.html
@Vladimir-hq1ne6 жыл бұрын
I've seen that piston motor 1st time in my life. And I've lived without that knowledge for 45 years. Pity me. thank you, AvE and whoever sent this motor to disassemble! This is really amazing! Thank ya'll for the enlightenment!
@nissearkevid19956 жыл бұрын
This is the coolest piece of gear you've disassembled ever. Thumbs up!
@Fredtheswedex
6 жыл бұрын
Biased!
@martinxXsuto
6 жыл бұрын
The variable displacement pump was also cool
@zadrik13376 жыл бұрын
That clean mat is hurting my eyes! Spill some schmoo on it right quick before bad karma finds you... Too late, breaker blew.
@jonasnacinovich6 жыл бұрын
Well fuck, I thought I'd have a cool comment in saying I've been swapping out Parker parts for ten years on various aircraft in Manitoba. But I guess the Swedish dude who plasma nitrated this stuff has me beat. Anyway, thanks to the masked hero who stole the part from work for the sake of this vijayo. Cool shit inside that little gem
@russellashburn62686 жыл бұрын
For a bit of history, the reason these motors are made in Sweden is because this motor style was invented by Volvo and were bought by Parker. They have been the best motor in the industry for years. These motors are one of the few things that Parker has bought and just left alone because anything they changed would just screw it up.
@bobsacamano4648
6 жыл бұрын
Actually this motor was a product of VOAC, a collaboration between Volvo and Atlas-Copco. VOAC was bought out by Parker Hannifin
@pauldavidson6321
5 жыл бұрын
@@bobsacamano4648 it was Volvo before it was voac ,been using them for 30 years now.
@IchigoKurosaki776 жыл бұрын
Good job old mat. You walked the path and passed the trial. You enjoy your retirement on the other bench. *Amazing Grace played by bagpipes*
@Ariccio123
6 жыл бұрын
Patrick IKNOWKUNGFU *taps* tho
@IchigoKurosaki77
6 жыл бұрын
Alexander Riccio That works too.
@Fireholder1
5 жыл бұрын
Red Green, is that you?
@BlankBrain6 жыл бұрын
I had a summer job building axles for mobile homes and travel trailers. They modified the assembly line to weld the spindles onto the axles rather than having pre-built axles. Brilliantly, they didn't allow space or time for the axles to cool before assembly. We got pretty good at spitting on the axles to tell how hot they were so we could guess how much to preload the wheel bearings. By the time they got past the leaf spring assembly station, they had cooled enough to be inspected.
@tbernardi0016 жыл бұрын
"That's quite a small shaft" If I had a dollar for every time I've heard that.
@junky5422
6 жыл бұрын
Tell em you'll make it up with the 1200 rippems. Enough friction to boil a kettle in 60 seconds...
@DrSlay1313
6 жыл бұрын
60 seconds is a long time.
@timrobinson9192
6 жыл бұрын
I'll second that !
@hygrometer6 жыл бұрын
for years ive been waiting for this day. NEW CUTTING MAT! unbelievable
@mikebrooka93956 жыл бұрын
When I read your post, I said to myself "Self, he has a hydrostatic motor or fixed volume pump with over pressure release." All you need is a variable swash plate pump to make it go backwards or forward in infinite increments. Check out the hydrostatic Eaton units on things like smaller Toro front deck riding mower, self propelled concrete saws, and even the lowly MTD brands of hydrostatic transaxles (Eaton hydrostatic units). Lots of fun to play with and many shop uses. I used them for riding mower racing (hint, if you stress them like I did, sinister 10w40). Take care from Oklahoma, Mike and the old lady that hates my cigars 😎
@usquanigo6 жыл бұрын
"Never force it, just find a bigger hammer" lol!
@SecondLifeDesigner6 жыл бұрын
A lot of the stuff in the video goes over my head but I so enjoy the process and narration and usually end up learning a thing or two. :)
@TriccyViccy6 жыл бұрын
"100 horsepower in your hand"? That's what I brag about in regards to my... Drill. Also, RIP cutting mat. You will be remembered O7
@jimallen14856 жыл бұрын
Does your shop look like the rest of your bench? My shop and bench are a clutter disaster. My wife wants me to clean it up. I told her I was waiting for the appraiser so I could stick a 2 million dollar price tag on it and sell it as modern art.
@VictorGarciaR
6 жыл бұрын
I bought another workwench, lighter duty. Now all the crap is on there
@christinamichelle2830
6 жыл бұрын
The only answer is to build a bigger bench.
@jaronbernard9911
6 жыл бұрын
I built 2 work benches, albeit from dead tree carcass, but at least it’s cypress right
@The_sinner_Jim_Whitney3 жыл бұрын
Damn, that thing is AWESOME! I’ve never seen (or at least never known that I was seeing) one of these. What a cool unit, thanks to whoever sent it, seriously.
@oscarwitte4936 жыл бұрын
Covered these pumps two days ago in aviation maintenance school. Perfect timing, thank you!
@BruiserBob6 жыл бұрын
I couldn't be prouder than I am being a patreon of this channel. Every AvE video gives me nothing but joy. Cool as hell as always man!
@stuffyours5 жыл бұрын
Best video ive seen of yours yet sir! Very cool piece and so interesting how that damn thing works.
@Steevo696 жыл бұрын
The shaft got etched (scale prevention) during processing to ensure no cracks/surface flaws formed during or from the drop forging, milling, or heat treatment process after, the bearing race, the only "to tolerance" fits were machined after heat treatment and the whole part then probably underwent a final surface hardening, the threads were rolled on directly after forging.
@mysock351C6 жыл бұрын
The machining looks like what you'd see in a car transmission. Very nice and the taper rollers look more like bearings for a rear end. Must be under a lot of load, for sure.
@sirthicenskoorb36846 жыл бұрын
I don't understand the technical jargon but love the colorful jargon. My grandparents raised my aunts in Canada. One aunt used old sayings. What a card. I always watch your videos.
@luisvillalobos6517 Жыл бұрын
What a beautifully designed and built piece. Good lordy. Such a beaut
@TheWisehydralisk6 жыл бұрын
Wanted say that I was teaching my trainee at work how to torque a cylinder head. I used your method of a grunt and a click. He kinda of gave me a clueless look then proceeded to torque the rest of the head that way. Took me 20 minutes of explaining how to actually torque some thing and the importance of it. Thank god it was a junk engine that he was practicing on. As always love the vids you basically mirror my personality.
@obscenitron6 жыл бұрын
I give it a week... and it'll match the last one.
@Bluuplanet6 жыл бұрын
I have an old transmission from a WWII bomb bay door that contains two of these bent angle piston thingys. One is a motor at a fixed angle like this one. The other, in the same cast aluminum case is a variable angle piston pump. Since it's variable angle, an angle gear around the perimeter of the 5-shooter cylinder wouldn't work, instead, there's a CV driveshaft through the center. the angle is adjustable with a lever outside the case. It goes from zero degrees (where the output shaft doesn't move) up to an angle equal to the output bent angle (where the output shaft rotates at the same speed as the input). It was all fastened together with wired screws. I took it apart years ago and couldn't figure out how to get the parts back together. Its in my garage in a plastic bag and a coffee can of oil.
@ThriftStoreHacker6 жыл бұрын
Wow. What an amazing bit of equipment AND a fancy new mat! Living the dream.
@tyler1h235 жыл бұрын
I just want to say that I absolutely LOVE your videos!!! I literally watch at least 2-4 a day if I can help it and have the free time. The depth in which you break each piece down and explain what you're seeing is just plain fucking fantastic. LOVE IT MAN!! But also. What ANDROID borescope are you using and where did you pick it up from?
@MrSheaonemillion5 жыл бұрын
Thank you very much for all the weird machines and great explanations!
@rimmersbryggeri6 жыл бұрын
We make alot of industrial stuff in sweden. When I made haldex parts we had UNC UNF NPT and metric within the same part. Pipe fittings are often sold as metric these days but they are all compatible with BSP threads whether they are cylindrical or tapered. At least the ones I have used.
@TheJustin5746 жыл бұрын
I had a smile on my face when you said 100HP, that was my guess!
@stalkinghawk92446 жыл бұрын
AVE, I have to thank you for showing all these things, besides your VFD COmpressor video inspired me, Right now I've gone full Canadian and I´m in the middle of running my 3kw compressor on a VFD and PLC combo to automate stuff. I already have plans(and working examples on drawers) for automatic pneumatic doors. In the summer ill take on a hydraulic project.
@Smikkelboy696 жыл бұрын
Its awesome to see such nicely made tools. Thank you for another great video :)
@John_Ridley6 жыл бұрын
Fantastic! I love finding out about new ingenious stuff that has been invented.
@dylangray15796 жыл бұрын
ive done hydraulic pump repair for years. just recently got a job at parker hannifin in the hydraulic pump division
@anthonyblacker84713 жыл бұрын
I worked for Parker Hannifin when i was in school.. it was a small shop, we made hydraulic fittings and some small pump machines.. it was a neat place
@jamesmccabe1036 жыл бұрын
"Worse than java" I lost it man, Keep up the good work!
@budude26 жыл бұрын
Even though I've heard it a hundred times and even though I know it's coming, I still giggle like a little girl when you blurt out the 'ol 'give it a little tappy-tappy-tap-tap'...
@damedog19
6 жыл бұрын
It's the little things in life
@n1r0lanynonmouse6
6 жыл бұрын
What is amazing is watching other videos of guys working on cars, machines, etc. and hearing them say the same thing. "Aha, another cult member! Welcome"
@steve1978ger
6 жыл бұрын
... what's that about anyway, sounds like he is channeling Chef John or something.
@UPrider9885 жыл бұрын
@AvE, take a look at parker hydraulic hybrid transmissions. They used to use a pump that varied displacement all the way to a negative value to make it a motor as well. Really cool technology that never took off.
@austinJRu6 жыл бұрын
Awesome man. Diggin the hydraulic stuff. Thanks for sharing.
@WoodWorkLIFE6 жыл бұрын
Japanese woodworking hand tools are awesome as well, there are scammers out there all over the place capitalizing on Japanese maker and brand names, but the antique stuff is amazing. Keep up the awesome vids, you are the uncle bumblefuck I always wish I had...
@dylanheadrick37896 жыл бұрын
Those piston sealing rings on the pushrods look incredibly similar to the gas rings on the rear of an ar-15 bolt. They use 3 steel rings to seal against the interior of the bolt carrier to allow gas pressure to unlock the bolt face from the chamber.
@raysplace65486 жыл бұрын
The best vids on KZread.. Good stuff man.
@PsiCommando4 жыл бұрын
I like how you keep your workbench nice and tidy :D
@pauldeer62586 жыл бұрын
This is a similar mechanism to how a Karcher 3600psi pressure sprayer works, just in reverse. The petrol motor drives the input shaft. That has an off axis plate that pushes 5 pistons back and forth as it rotates to boost the pressure of the fluid giving you high pressure fun.
@glenralph51236 жыл бұрын
Awesome motor and vid, cheers! Back to Chris at Clickspring.... cheers for that hot little tip too, brother!
@docking_bay_946 жыл бұрын
Thanks for the stickers. Very cool. They are the very first adornments for my very new and also very first tool chest.
@gabbermaikel6 жыл бұрын
nice to see a reliable source for the android bore scope video quality. Was looking to buy 1 this week, but wasnt sure about the quality. Have been using the borescope from my work, but well its kind of expensive, and i dont want to ruin expensive tools i borrow from my work at home.
@matthunter29526 жыл бұрын
O-ring boss comes in metric too. Closed circuit pumps have same size system ports. But they do mix sae and metric fasteners and ports on the same pump/motor. You're right though they are skookum as frig. I abuse them daily.
@GasNBullets6 жыл бұрын
Ok Time to build a hydraulic gokart!
@233kosta
6 жыл бұрын
Sign me up! I'll do the gas turbine driven pump!
@whereiseshan4 жыл бұрын
this type of motor is commonly used for hydro static drive motors in vehicles, hydraulic pump driven by engine will force hydraulic fluid into motor which you have to turn the wheels...pretty awesome stuff
@porklaser6 жыл бұрын
I got that same cutting mat for my workbench! Love it to death, but brand new it out gassed and stunk up the room for a few weeks after I got it. Olfa suggests washing it down with dilute vinegar to reduce the smell when it's new.
@georgebonney904 жыл бұрын
Cant tell u how much i appreciate the share of knowledge
@Ace1Of1All1Spades6 жыл бұрын
As a millwright apprentice I appreciate the shout-out. Also I love my learner hammers and brass rods 😁
@thomas3166 жыл бұрын
"Double lip seal" Am I awake right now? 🤔 I didn't know I had a preference for seals but it turns out I now have a favourite. 😄
@CMDRunematti6 жыл бұрын
love those, pulled one apart once, from a friction welding machine, they can do 18k rpm (seen them hit 26k)
@HamiltonSRink6 жыл бұрын
Very Cool Video! BTW, I really enjoyed the Christmas story !
@jonathanhigginbotham69646 жыл бұрын
I have watched for about 5 months and seen most of your videos but I'm lost as to what AvE stands for? Love your stuff keep it up ☝
@Leffe192
6 жыл бұрын
Arduinos versus evil... Goes way back, he has shifted focus slightly since.
@jonathanhigginbotham6964
6 жыл бұрын
Thank you ive been wondering for ever, he inspired me to start a channel again. Wish there were more people like him.
@TySoVm6 жыл бұрын
Brought back flashbacks to rebuilding my ford 8.8 diff, getting those carrier bearings off nearly killed me.
@Simon-eh5ez5 жыл бұрын
Fun fact, this is probably built here in little Trollhättan, next to GKN (old volvo aero) which makes jet engines for SAAB technologies and a lot of other stuff including rocket parts. Next door again is the SAAB Automobile factory which now houses NEVS.
@cubby6126 жыл бұрын
The lines on the old mat were finally worn enough to allow the camera to focus on the subject. Perfect.
@reillyc76054 жыл бұрын
There are specific torque specs. For the lock nut depending on the size of bearing. There is even a chart for how many degrees you need to turn the lock nut if you can not measure torque.
@curtjrich156 жыл бұрын
I like olfa products aswell. I just recieved thier newest knife in the mail, excited to check it out when i get home. Model LA-X, with an autolock, and an all purpose pick for opening paint cans/prying small things.
@scottsarchitecturehildebra17616 жыл бұрын
Amazing, a fantastic upgrade!!! Sooooo dig the speak!!!
@superdude1230326 жыл бұрын
New cutting mat. Time to celebrate boys. I’ve got that same hex key set. Bought a couple of sets on sale at Menards.
@Meepster126 жыл бұрын
So good to see that I'm not the only one struggling in the shop!
@desertforgeknifetool21426 жыл бұрын
Your channel is awesome!
@benwinckler1316 жыл бұрын
Those metal things are shims and they are there to evenly space the gears to give variable gear backlash cause those things spin at 3100 rpm (hey i wrote this halfway through so 3100 was a geuss until I watched it all) and as they need rebuilds the gear teeth wear and need to be closer in backlash There is a lumber yard with two of these and it is a saur danfoss with 1 inch pistons (8 of them) to drive an 8 foot sawblade
@ninney7946 жыл бұрын
I fucking love your vijayos! Such a wealth of knowledge you hold! Reminds me of my grandfather, I'd like to know half of what he had forgotten over the years haha.
@pauljs756 жыл бұрын
It's a lot like a tilt-block motor. Except the bit where the block would be is part of the case, thus no variable angle to it. (Those are kind of neat too, variable speed and variable stroke for a given flow rate.)
@ricknelson78244 жыл бұрын
Actually it used to be branded Volvo bent axial piston motor. Looks like a c10 version designed for around 12 gpm at max 2200 psi. Horsepower would be more like 25-20 hp. Generally rpm as a fan drive was 5000 rpm. They can spin faster but at a cost in longevity. Biggest problem was if case drain was restricted and not free flow to tank. Lip seal on shaft would fail.
@logger12236 жыл бұрын
Some good quality stuff from my hometown Trollhättan, Sweden ;)
@michaelbohanon81376 жыл бұрын
End of an erra. RIP old OLFA mat. Thanks for the excellent TGIF fodder and..I just got a scope like that for my Android too. Crazy cool eh!! Keep up the keeping up Bumblefook!
@couldntthinkofagoodnamesoi83573 ай бұрын
Beautiful piece of gear.
@marcjordan296 жыл бұрын
Loving the "tappy taep taep"...... And the 5/8ths SHAFT
@AverilDoyle6 жыл бұрын
Am I the only one who expected him to just flip over the cutting mat??
@SpoiledBadgerMilk6 жыл бұрын
I am no engineer. But mIwatch all your videos. Lol I love watching things get taken apart. I learn allot any how great video keep it up.
@richardshortman56456 жыл бұрын
Knipex! One of the most useful tools out there. That and a screwdriver and DMV would fix half of all the stuff in the plants.
@hg4lyfe6 жыл бұрын
Amazing video love your work
@ZylonFPV6 жыл бұрын
The new cutting mat is beautiful 💖
@ureviews6 жыл бұрын
This was mesmerizing. Unbelievable design and quality! How much does something like that cost?
@Slowpoke50556 жыл бұрын
I have learned something today. Thank You
@wheelitzr26 жыл бұрын
Those 2 things that fell out at the beginning are shims to space the gears. That's why it runs rough and doesn't want to start.
@pravoslavac106 жыл бұрын
Awesome, just got that same mat a couple days ago. Sure takes a while for that off gassing smell to go away.
@pravoslavac10
6 жыл бұрын
Thanks, I'll give that a shot.
@petergriffin3836 жыл бұрын
AvE makes me piss my pants laughing almost every time..."for fucks sake!, it doesn't end boys...it...just...doesn't....end"
@danethibodeaux98926 жыл бұрын
I work on these for a living. We supply Parker. That's a fixed displacement motor. Good product
@danethibodeaux98926 жыл бұрын
If I'm not mistaken the piston barrel on that model is timed. If you don't line up the timing marks you till blow the piston apart
@mikebrowne51526 жыл бұрын
Looks like the frosted surface finish on the shaft drive is from heat treatment and tumbling then the seal race was finish ground.
@allanwilson86426 жыл бұрын
I understood very little of the technical content but privileged to witness the advent of new cutting mat day.
@robertsilversten76262 жыл бұрын
There index point on the cylinder and barrel for timing. You can see them through the case drain port. 99 percent of the Tim they have them in good measure before you pop it open look through the port while rotating if you don’t see it you could punch the gear and the barrel teeth.
@rynohorn38196 жыл бұрын
Only understand half of what you're saying but I enjoy the show. Thanks AvE
@millsbrian556 жыл бұрын
Had some good laughs at this one! More FPM’s than usual...sounds like me in my shop...
@festekosky4 жыл бұрын
Generally small pumps don't have leak lines, they port back to the inlet
@jackcaldwell4856 жыл бұрын
I still can hear you do " happy tap tap, and finding a hair and gagging" 😂😂
@thedevilinthecircuit14145 ай бұрын
"These are great, man...Android bore scopes for fifteen bucks OH FOR FUCKS SAKES!" This is the song of my people.
Пікірлер: 835
I'm from Sweden and as soon as you popped that open i recognized the parts. I used to harden those. They are plasma nitrated.
@arduinoversusevil2025
6 жыл бұрын
Thanks man!
@tjockiskatten
6 жыл бұрын
AvE No, thank you! It must be about 7 or 8 years since I worked with metal hardening. You just gave me some fond memories.
@PyroShim
6 жыл бұрын
This is why i still use youtube!
@MrPruske
6 жыл бұрын
great info can still be found :)
@Lillebroor
6 жыл бұрын
I worked at Parker too here in Sweden. As a machinist where they produced the hydraulic blocks. =)
Leakage is cooling, gotcha, it's like I say with my old volvo wheel loader from -79, if it's leaking oil, it's got oil.
@Valtra-rn1ed
6 жыл бұрын
Affra thats what i always say! Start worrying when it stops leaking!
@aPreciousPiggy
6 жыл бұрын
Only way to know if there's oil in it is if there's oil under it.
@perlandstrom5023
6 жыл бұрын
Yeah no need for a dipstick XD
@AndersJackson
6 жыл бұрын
And it is good against rust too.
@mmurola9859
6 жыл бұрын
Someone told me he saw an old Caterpillar wheel loader where instead of the transmission fill plug there was a tap. Each evening the operator would drain several liters of oil from the trans and pour it into the hydraulic tank. He sai "I'll just put it back where it came from". Had a leaking transmission mounted hydraulic pump so the oil came from the hydraulics system. Also heard of a Lännen loader excavator that had a sheet metal pan suspended by chains under it's belly to catch the drips. :)
New mat = another foundry vijayo
Ah yes! Another AvE vijeo! Dear Bumblefuck, I leave you with a thoughtful poem.. Mary had a little lamb It ran into a pylon. 10,000 volts went up its ass and turned its wool to nylon
@altfseven
6 жыл бұрын
nbrosens Mary had a little lamb He farther shot it dead Now she takes it to her school Between 2 chunks of bread
@steviefordranger198
6 жыл бұрын
LOL, love it.
@timrobinson9192
6 жыл бұрын
Mary had a little pig She couldn't stop it gruntin' Once it got right on her nerves She kicked it's fucking C**t in !
"It's starting to get a little haggard around the edges." I'd say it's more haggard in the middle, where you poured molten aluminum on it.
@timothybarney7257
6 жыл бұрын
I was thinking that as well...the edge was the only good part left!
A new self-healing cutting mat? Nooo! I used to be able to tell roughly how old a video was by the condition of its battlescars. Now you've gone and destroyed all that precious chronological metadata. You fool. Hopefully her time away from the main bench lets her plastic nanites work their magic and in a few months we'll see her back in competition form.
@pubcollize
6 жыл бұрын
This one is clearly bigger though. So now we can have an eaven rougher estimation based on which cutting mat is shown. Let them be known as Bigger Cuttingmat and Authentic Deck. AKA B.C and A.D.
@LucasGarrow
6 жыл бұрын
Like being able to tell what season we're in.
@MikeCookie1973
6 жыл бұрын
Go back a bit, and you might find when the previous one was put into service...
@jonathanryals9934
6 жыл бұрын
I'd say one a year is 'bout right.
@tattmanndann
6 жыл бұрын
MikeCookie1973 here i think .kzread.info/dash/bejne/aaSCj8inhcinY9I.html
I've seen that piston motor 1st time in my life. And I've lived without that knowledge for 45 years. Pity me. thank you, AvE and whoever sent this motor to disassemble! This is really amazing! Thank ya'll for the enlightenment!
This is the coolest piece of gear you've disassembled ever. Thumbs up!
@Fredtheswedex
6 жыл бұрын
Biased!
@martinxXsuto
6 жыл бұрын
The variable displacement pump was also cool
That clean mat is hurting my eyes! Spill some schmoo on it right quick before bad karma finds you... Too late, breaker blew.
Well fuck, I thought I'd have a cool comment in saying I've been swapping out Parker parts for ten years on various aircraft in Manitoba. But I guess the Swedish dude who plasma nitrated this stuff has me beat. Anyway, thanks to the masked hero who stole the part from work for the sake of this vijayo. Cool shit inside that little gem
For a bit of history, the reason these motors are made in Sweden is because this motor style was invented by Volvo and were bought by Parker. They have been the best motor in the industry for years. These motors are one of the few things that Parker has bought and just left alone because anything they changed would just screw it up.
@bobsacamano4648
6 жыл бұрын
Actually this motor was a product of VOAC, a collaboration between Volvo and Atlas-Copco. VOAC was bought out by Parker Hannifin
@pauldavidson6321
5 жыл бұрын
@@bobsacamano4648 it was Volvo before it was voac ,been using them for 30 years now.
Good job old mat. You walked the path and passed the trial. You enjoy your retirement on the other bench. *Amazing Grace played by bagpipes*
@Ariccio123
6 жыл бұрын
Patrick IKNOWKUNGFU *taps* tho
@IchigoKurosaki77
6 жыл бұрын
Alexander Riccio That works too.
@Fireholder1
5 жыл бұрын
Red Green, is that you?
I had a summer job building axles for mobile homes and travel trailers. They modified the assembly line to weld the spindles onto the axles rather than having pre-built axles. Brilliantly, they didn't allow space or time for the axles to cool before assembly. We got pretty good at spitting on the axles to tell how hot they were so we could guess how much to preload the wheel bearings. By the time they got past the leaf spring assembly station, they had cooled enough to be inspected.
"That's quite a small shaft" If I had a dollar for every time I've heard that.
@junky5422
6 жыл бұрын
Tell em you'll make it up with the 1200 rippems. Enough friction to boil a kettle in 60 seconds...
@DrSlay1313
6 жыл бұрын
60 seconds is a long time.
@timrobinson9192
6 жыл бұрын
I'll second that !
for years ive been waiting for this day. NEW CUTTING MAT! unbelievable
When I read your post, I said to myself "Self, he has a hydrostatic motor or fixed volume pump with over pressure release." All you need is a variable swash plate pump to make it go backwards or forward in infinite increments. Check out the hydrostatic Eaton units on things like smaller Toro front deck riding mower, self propelled concrete saws, and even the lowly MTD brands of hydrostatic transaxles (Eaton hydrostatic units). Lots of fun to play with and many shop uses. I used them for riding mower racing (hint, if you stress them like I did, sinister 10w40). Take care from Oklahoma, Mike and the old lady that hates my cigars 😎
"Never force it, just find a bigger hammer" lol!
A lot of the stuff in the video goes over my head but I so enjoy the process and narration and usually end up learning a thing or two. :)
"100 horsepower in your hand"? That's what I brag about in regards to my... Drill. Also, RIP cutting mat. You will be remembered O7
Does your shop look like the rest of your bench? My shop and bench are a clutter disaster. My wife wants me to clean it up. I told her I was waiting for the appraiser so I could stick a 2 million dollar price tag on it and sell it as modern art.
@VictorGarciaR
6 жыл бұрын
I bought another workwench, lighter duty. Now all the crap is on there
@christinamichelle2830
6 жыл бұрын
The only answer is to build a bigger bench.
@jaronbernard9911
6 жыл бұрын
I built 2 work benches, albeit from dead tree carcass, but at least it’s cypress right
Damn, that thing is AWESOME! I’ve never seen (or at least never known that I was seeing) one of these. What a cool unit, thanks to whoever sent it, seriously.
Covered these pumps two days ago in aviation maintenance school. Perfect timing, thank you!
I couldn't be prouder than I am being a patreon of this channel. Every AvE video gives me nothing but joy. Cool as hell as always man!
Best video ive seen of yours yet sir! Very cool piece and so interesting how that damn thing works.
The shaft got etched (scale prevention) during processing to ensure no cracks/surface flaws formed during or from the drop forging, milling, or heat treatment process after, the bearing race, the only "to tolerance" fits were machined after heat treatment and the whole part then probably underwent a final surface hardening, the threads were rolled on directly after forging.
The machining looks like what you'd see in a car transmission. Very nice and the taper rollers look more like bearings for a rear end. Must be under a lot of load, for sure.
I don't understand the technical jargon but love the colorful jargon. My grandparents raised my aunts in Canada. One aunt used old sayings. What a card. I always watch your videos.
What a beautifully designed and built piece. Good lordy. Such a beaut
Wanted say that I was teaching my trainee at work how to torque a cylinder head. I used your method of a grunt and a click. He kinda of gave me a clueless look then proceeded to torque the rest of the head that way. Took me 20 minutes of explaining how to actually torque some thing and the importance of it. Thank god it was a junk engine that he was practicing on. As always love the vids you basically mirror my personality.
I give it a week... and it'll match the last one.
I have an old transmission from a WWII bomb bay door that contains two of these bent angle piston thingys. One is a motor at a fixed angle like this one. The other, in the same cast aluminum case is a variable angle piston pump. Since it's variable angle, an angle gear around the perimeter of the 5-shooter cylinder wouldn't work, instead, there's a CV driveshaft through the center. the angle is adjustable with a lever outside the case. It goes from zero degrees (where the output shaft doesn't move) up to an angle equal to the output bent angle (where the output shaft rotates at the same speed as the input). It was all fastened together with wired screws. I took it apart years ago and couldn't figure out how to get the parts back together. Its in my garage in a plastic bag and a coffee can of oil.
Wow. What an amazing bit of equipment AND a fancy new mat! Living the dream.
I just want to say that I absolutely LOVE your videos!!! I literally watch at least 2-4 a day if I can help it and have the free time. The depth in which you break each piece down and explain what you're seeing is just plain fucking fantastic. LOVE IT MAN!! But also. What ANDROID borescope are you using and where did you pick it up from?
Thank you very much for all the weird machines and great explanations!
We make alot of industrial stuff in sweden. When I made haldex parts we had UNC UNF NPT and metric within the same part. Pipe fittings are often sold as metric these days but they are all compatible with BSP threads whether they are cylindrical or tapered. At least the ones I have used.
I had a smile on my face when you said 100HP, that was my guess!
AVE, I have to thank you for showing all these things, besides your VFD COmpressor video inspired me, Right now I've gone full Canadian and I´m in the middle of running my 3kw compressor on a VFD and PLC combo to automate stuff. I already have plans(and working examples on drawers) for automatic pneumatic doors. In the summer ill take on a hydraulic project.
Its awesome to see such nicely made tools. Thank you for another great video :)
Fantastic! I love finding out about new ingenious stuff that has been invented.
ive done hydraulic pump repair for years. just recently got a job at parker hannifin in the hydraulic pump division
I worked for Parker Hannifin when i was in school.. it was a small shop, we made hydraulic fittings and some small pump machines.. it was a neat place
"Worse than java" I lost it man, Keep up the good work!
Even though I've heard it a hundred times and even though I know it's coming, I still giggle like a little girl when you blurt out the 'ol 'give it a little tappy-tappy-tap-tap'...
@damedog19
6 жыл бұрын
It's the little things in life
@n1r0lanynonmouse6
6 жыл бұрын
What is amazing is watching other videos of guys working on cars, machines, etc. and hearing them say the same thing. "Aha, another cult member! Welcome"
@steve1978ger
6 жыл бұрын
... what's that about anyway, sounds like he is channeling Chef John or something.
@AvE, take a look at parker hydraulic hybrid transmissions. They used to use a pump that varied displacement all the way to a negative value to make it a motor as well. Really cool technology that never took off.
Awesome man. Diggin the hydraulic stuff. Thanks for sharing.
Japanese woodworking hand tools are awesome as well, there are scammers out there all over the place capitalizing on Japanese maker and brand names, but the antique stuff is amazing. Keep up the awesome vids, you are the uncle bumblefuck I always wish I had...
Those piston sealing rings on the pushrods look incredibly similar to the gas rings on the rear of an ar-15 bolt. They use 3 steel rings to seal against the interior of the bolt carrier to allow gas pressure to unlock the bolt face from the chamber.
The best vids on KZread.. Good stuff man.
I like how you keep your workbench nice and tidy :D
This is a similar mechanism to how a Karcher 3600psi pressure sprayer works, just in reverse. The petrol motor drives the input shaft. That has an off axis plate that pushes 5 pistons back and forth as it rotates to boost the pressure of the fluid giving you high pressure fun.
Awesome motor and vid, cheers! Back to Chris at Clickspring.... cheers for that hot little tip too, brother!
Thanks for the stickers. Very cool. They are the very first adornments for my very new and also very first tool chest.
nice to see a reliable source for the android bore scope video quality. Was looking to buy 1 this week, but wasnt sure about the quality. Have been using the borescope from my work, but well its kind of expensive, and i dont want to ruin expensive tools i borrow from my work at home.
O-ring boss comes in metric too. Closed circuit pumps have same size system ports. But they do mix sae and metric fasteners and ports on the same pump/motor. You're right though they are skookum as frig. I abuse them daily.
Ok Time to build a hydraulic gokart!
@233kosta
6 жыл бұрын
Sign me up! I'll do the gas turbine driven pump!
this type of motor is commonly used for hydro static drive motors in vehicles, hydraulic pump driven by engine will force hydraulic fluid into motor which you have to turn the wheels...pretty awesome stuff
I got that same cutting mat for my workbench! Love it to death, but brand new it out gassed and stunk up the room for a few weeks after I got it. Olfa suggests washing it down with dilute vinegar to reduce the smell when it's new.
Cant tell u how much i appreciate the share of knowledge
As a millwright apprentice I appreciate the shout-out. Also I love my learner hammers and brass rods 😁
"Double lip seal" Am I awake right now? 🤔 I didn't know I had a preference for seals but it turns out I now have a favourite. 😄
love those, pulled one apart once, from a friction welding machine, they can do 18k rpm (seen them hit 26k)
Very Cool Video! BTW, I really enjoyed the Christmas story !
I have watched for about 5 months and seen most of your videos but I'm lost as to what AvE stands for? Love your stuff keep it up ☝
@Leffe192
6 жыл бұрын
Arduinos versus evil... Goes way back, he has shifted focus slightly since.
@jonathanhigginbotham6964
6 жыл бұрын
Thank you ive been wondering for ever, he inspired me to start a channel again. Wish there were more people like him.
Brought back flashbacks to rebuilding my ford 8.8 diff, getting those carrier bearings off nearly killed me.
Fun fact, this is probably built here in little Trollhättan, next to GKN (old volvo aero) which makes jet engines for SAAB technologies and a lot of other stuff including rocket parts. Next door again is the SAAB Automobile factory which now houses NEVS.
The lines on the old mat were finally worn enough to allow the camera to focus on the subject. Perfect.
There are specific torque specs. For the lock nut depending on the size of bearing. There is even a chart for how many degrees you need to turn the lock nut if you can not measure torque.
I like olfa products aswell. I just recieved thier newest knife in the mail, excited to check it out when i get home. Model LA-X, with an autolock, and an all purpose pick for opening paint cans/prying small things.
Amazing, a fantastic upgrade!!! Sooooo dig the speak!!!
New cutting mat. Time to celebrate boys. I’ve got that same hex key set. Bought a couple of sets on sale at Menards.
So good to see that I'm not the only one struggling in the shop!
Your channel is awesome!
Those metal things are shims and they are there to evenly space the gears to give variable gear backlash cause those things spin at 3100 rpm (hey i wrote this halfway through so 3100 was a geuss until I watched it all) and as they need rebuilds the gear teeth wear and need to be closer in backlash There is a lumber yard with two of these and it is a saur danfoss with 1 inch pistons (8 of them) to drive an 8 foot sawblade
I fucking love your vijayos! Such a wealth of knowledge you hold! Reminds me of my grandfather, I'd like to know half of what he had forgotten over the years haha.
It's a lot like a tilt-block motor. Except the bit where the block would be is part of the case, thus no variable angle to it. (Those are kind of neat too, variable speed and variable stroke for a given flow rate.)
Actually it used to be branded Volvo bent axial piston motor. Looks like a c10 version designed for around 12 gpm at max 2200 psi. Horsepower would be more like 25-20 hp. Generally rpm as a fan drive was 5000 rpm. They can spin faster but at a cost in longevity. Biggest problem was if case drain was restricted and not free flow to tank. Lip seal on shaft would fail.
Some good quality stuff from my hometown Trollhättan, Sweden ;)
End of an erra. RIP old OLFA mat. Thanks for the excellent TGIF fodder and..I just got a scope like that for my Android too. Crazy cool eh!! Keep up the keeping up Bumblefook!
Beautiful piece of gear.
Loving the "tappy taep taep"...... And the 5/8ths SHAFT
Am I the only one who expected him to just flip over the cutting mat??
I am no engineer. But mIwatch all your videos. Lol I love watching things get taken apart. I learn allot any how great video keep it up.
Knipex! One of the most useful tools out there. That and a screwdriver and DMV would fix half of all the stuff in the plants.
Amazing video love your work
The new cutting mat is beautiful 💖
This was mesmerizing. Unbelievable design and quality! How much does something like that cost?
I have learned something today. Thank You
Those 2 things that fell out at the beginning are shims to space the gears. That's why it runs rough and doesn't want to start.
Awesome, just got that same mat a couple days ago. Sure takes a while for that off gassing smell to go away.
@pravoslavac10
6 жыл бұрын
Thanks, I'll give that a shot.
AvE makes me piss my pants laughing almost every time..."for fucks sake!, it doesn't end boys...it...just...doesn't....end"
I work on these for a living. We supply Parker. That's a fixed displacement motor. Good product
If I'm not mistaken the piston barrel on that model is timed. If you don't line up the timing marks you till blow the piston apart
Looks like the frosted surface finish on the shaft drive is from heat treatment and tumbling then the seal race was finish ground.
I understood very little of the technical content but privileged to witness the advent of new cutting mat day.
There index point on the cylinder and barrel for timing. You can see them through the case drain port. 99 percent of the Tim they have them in good measure before you pop it open look through the port while rotating if you don’t see it you could punch the gear and the barrel teeth.
Only understand half of what you're saying but I enjoy the show. Thanks AvE
Had some good laughs at this one! More FPM’s than usual...sounds like me in my shop...
Generally small pumps don't have leak lines, they port back to the inlet
I still can hear you do " happy tap tap, and finding a hair and gagging" 😂😂
"These are great, man...Android bore scopes for fifteen bucks OH FOR FUCKS SAKES!" This is the song of my people.