thanks for sharing! Good to see you back :)

You are doing a great job, by sharing, thanks alot.

it helps thanks

Replaced trans in my 335i auto. Never programmed because I didn’t have a clue. Switched gears great feels amazing but I’m getting clutch e codes and shift monitoring 4-5 codes when full throttle. Is the replacement junk or should I program first?

Thanks for your videos!! I do have a mini cooper F56 with simira issues after we replaced the module, I do have the IM608Pro with XP400pro, you mentioned that if you want to do it with the IM608 you should have some cables, what cables are those? Thanks again and greetings from Guatemala, Central America 😁

autel im508 can also reset the transmission? or are there cheaper scanner options?

Bro, Mercedes after crash airbag ohm change by ultra??

Tnx

If I replace the transmission mechatronics unit with a used one, Would this be the same coding that would need to be done ?

Boss ihave 1 question Can this scanner do also audi vw and Mercedes like this car imean with the obd on the car

@huyug1

11 ай бұрын

For Diag, and coding this tool is fine. But anything related to immobilizer you would need im508 or 608

I (DIY) replace my mechatronic with an OEM remanufactured unit and have the same symptoms not going into gear, do you think this is possibly my problem? 2011 BMW 750LI

@huyug1

9 ай бұрын

Yes, if it has not been programmed yet, definitely.

@huyug1

9 ай бұрын

You also need to renew transmission control unit as well if has been used before.

Hi there, I replaced the mechatronics unit on BMW e70 x5 and I am getting coding successful but progeamming failed. I am using ms909, any ideas? Car is stuck in park. I swapped the old unit back in and the car got into the gear again. I am scratching my head, your help would be appreciated

@Bruno-xb2mt

Ай бұрын

Mechatronics are pretty solid made so you might want to try changing the TCU/GWS. If you’re for sure its not that then some people say you cant code a used mechatronics unit in, only a new one but there’s probably a way around it if you know someone smart enough

BMW used ews in xtool h6 is possible

Is this the “programming “ after you install a used transmission?

@huyug1

10 ай бұрын

This is only the coding if during renewing module coding fails. I have another video that also shows how to renew or virginize the TCM

Question probably will never be answered. But if I get new valvebody. But reuse the tcm. Do I still have to code

@Aautotech.

2 ай бұрын

no

Hi, I changed out the gasket and transmission pan on my 2008 BMW 750li now my scanner can't pick up the transmission TCU and my car won't start. Could this be the issue with my car?

@biem8859

3 ай бұрын

Hello! I have the same problem. Did U fixed it?

@Bigray1993

3 ай бұрын

@@biem8859 Not yet, I'm taking it to my second transmission shop to see what they say. They specialize in BMW & Range Rover repairs

@biem8859

3 ай бұрын

​@@Bigray1993 My problem was fixed yesterday. It was the sleeve at the x8500 connector. Because the sleeve was installed incorrectly at the connector.

Hi I changed transmission and mod from 2019 X1 BMW into 2017 Mini Countryman 2l can you help me no one can clear codes and reprogram Thanks

are you still doing bmw dme work?

@huyug1

9 ай бұрын

Yes

@soundsoflife6224

9 ай бұрын

i have an 08 x5 dme has water damage. i got a used dme. can it be coded to my vehicle?@@huyug1

@vesoradev

4 ай бұрын

​@@huyug1Hello, are you able to do this remotely? 2012 X5 with zf 8hp