Great video. I've been looking for something like this for years

Nice job man seriously, this was long over due.

It is awesome to see the maturation of the engineering with BMWs, you can see the history of some things that carry over and other things dont. Awesome video

@crank3646

2 жыл бұрын

Thanks Joel!

Well done. This is probably the only video in the tube comparing 4 generations of BMW petrol engines. Keep the great uploads, I am always looking forward the next one. Поздрави от Пловдив, желая Ви здраве и усмивки, за другото се купува бензин :)

@crank3646

2 жыл бұрын

Мерси подобно :)

This video is a gold mine of information! Thanks for sharing it

Thank you for making this video. Very informative!

Great videos all the necessary comparisons 🔥🔥

Excellent video and information, thank you 👍🏽

Thanks for making this video and sharing the knowledge.

Fantastic work, very helpful video!! Keep up the good work 👍 I've been researching possibilities for creating a 3.3-3.4 litre m54b30 using bmw parts where possible and this really helped in ruling out certain engine block and had configurations. Ps looks like only way is a vacs motorsports 86mm bore resleeve kit and vacs 97mm stroker crank, then looking for appropriate piston & rod combination

Nice and useful videos! 🙏🏻👍

Dzięki wielkie za bardzo interesujący odcinek . Pozdrawiam

Really good video mate

Great video. Thanks from Rex in New Zealand.

Superb video comparison, thanks

This view of my M52 engine block is something I will never see but is always good to know info even if I won't be doing any engine work myself.

Really good video thank you very much. I read in an article that the M54 is better in terms of cooling. This video confirmed it.

Very good informative video!

Most useful video, i been ever seen.

Very interesting comparison👍

Thanks for the information! 👍

thank you for doing this

Great comparison. It would be interesting if you can make a video where you compare the crank and cams of the different engines.

@crank3646

2 жыл бұрын

I don't think is going to be so interesting, but if the demand is high I will see what can I do about it :)

@blade-vk

2 жыл бұрын

@@crank3646 everything here is about stroke, more power, torque... so i am in too!

@01sidiropoulos

2 жыл бұрын

A guy told me the capacity change from the stroke is it true that? So it would be lovely to see what happening with the cranks shafts ..!! Keep it up!

@MachoMostacho

2 жыл бұрын

@@01sidiropoulos Yes, M5X engines change their capacity modifying the stroke. m50b25 is 75mm stroke m52b28 is 84 and m54b30 89.6. The m5Xb25 use 140mm rods, while the B28 uses 135mm rods, the M54b30 uses 135mm. The only one that breaks this rule is the m5Xb20 which has a smaller bore, smaller valves and camshafts.

@86_E30_Blondie

2 жыл бұрын

@@MachoMostacho the M50B25 Non vanos uses 135mm rods, same length aswel as the b28 and b30 while the M50tüb25 (vanos) engine uses 140mm rods wich also makes the pistons different from one another

Great explanation guys. thanks for sharing. Have a great weekend, Dutch regards, Nico.

i needed this video thank you boss

This is great thank you.. helped me out a lot..

Thanks mate for a great education on the BMW blocks 👏👍⚙️🔧🔩😇

Thank you so much for a great video. Subscribe in the hope that you go into more detail with the M50B25. Just bought an E30 with that engine without any information from the seller.

Very good content!!¨Thank you!!

great video! thanks alot!

Много информативно видео, браво

Great job

thank you, interessting video

Awesome info thanks

Great video

Great video I have 3 builds with going same root as you i just hadn't figure out m54 oil pump on m50 yet great tip . Looking forward to seeing the single vanos on double vanos head cause I am doing same with s50 us cams if you selling that m50 block let me know 👍

@crank3646

2 жыл бұрын

Thanks! Haha this will be my relic :D

finalyyy someone made it!!!

Браво, добре си го направил

Beautiful!

The oil pump info I been wanting but was not looking for that right now just trying to see what motor I should use 😭 thank you

My M52B25 single vanos from E36 is made in 11/98 and it is with sleeves and damper crankshaft pulley. Its crank senson reads from flywheel.

браво много добро видео!!!!

In the u.s. everyone bores out the m50. Puts the m54 rotating assembly inside. The m54 crank is the same part number as a s52b32us. So its a small bore s52 clone. Great for boost. (I believe the rods and wrist pin locations are the same too?) just 84mm vs. The 86mm s52b32us . 87mm is the max you can bore s52b30 / m50 block. In the u.s. we got the m52 iron block. Its also 84mm. You can swap a m54b30 assembly right into a m52b28us (obd2 m50 single vanos, rear crank sensor. 96 to 99 in e36)

@drewdavis239

2 жыл бұрын

Non vanos m50 has different valve size.

@crank3646

2 жыл бұрын

Yep, but no one wants M54B30 crankshaft because its not reliable. So 2.8 is fine enough for me :)

Thank you 🙏

Great Video! Have been looking for a video like this for a long time! Do you have any experience of turbocharging a m52b28, some people say that it's not worth it and that the block will explode, and others say you can run 400hp easily. What do you think?

@od859

2 жыл бұрын

many people at my work have experiance with turboing m52s, youll be fine, 400 is a good number, decomp,. plate and headbolts is enough, and it wont explode. good luck bud, im gonna turbo my m50 once the rest of the car is sweet!

@peterm3861

2 жыл бұрын

As far as I know the internals are pretty durable. The biggest problem is that the old Bmw engines have pretty weak head bolts. They are pretty skinny (M10 only) which becomes even more difficult in aluminium blocks in my opinion. There are ways to bore out the threads and upgrade to M11 or even M12 but then you also have to drill cylinder head and even head gasket... Also the aluminium blocks are kind of sensitive to overheating. Once overheated in the past there is danger of the aluminium getting soft around the threads for the head bolts in the block so that they won't tighten anymore. However I don't know if you can eliminate this by boring out to M11 or bigger...

@aamaramba

2 жыл бұрын

@@peterm3861 Most popular option is ARP head studs for iron block turbo builds. They're proven to work great without the need to drill and tap the block to M11. Guys with 1000+hp use custom age 625+ arp studs for around $600. You're more likely to throw a rod through the block than lift the head with those studs.

@peterm3861

2 жыл бұрын

@@aamaramba Yeah in iron blocks some good head studs seem to do the job. I wonder if they would be a good solution for the alloy blocks or if the threads would just rip out. Newer all alloy engines use head bolts of greater diameter and length, that is really some weak point of the M5x engine family unfortunately. At least when boosting.

io I think bigger holl better flow .. were good widio . Big respect 👌❤️

FYI The so called freeze plugs are not for saving the block They are more correctly called core plugs and are filling holes left by the locating cores used to cast the block internal surfaces The aluminum casting process doesn't usually need them

Nice explain keep up But i Have questions can you add head gasket m50 on m52 and m54? Or just can you add head gasket m52b28tu on m54b30 because the both have double vanons please reply me and so thanks

Good video. I was wondering if there is a difference in quality between M52TUB28 crank, and a M52B28 non TU crank besides the trigger wheel? This is for M50 stroker and boost. Does it really matter?

The Nicasil coating was a market specific feature. So the newer engines having it could be from a different market.

Very intersed video... i have M50B20stroked 2497cc and used oil pump M52B20 single vanos :)

Thanks for the video! Your explanations are very good and it is great to see a fellow bulgarian make such cool informative videos about BMWs. I'm looking forward to buying my first BMW (i like the e46 the most) and i want to do a NA build without any crazy stroking. I would like to hear your opinion and anyone in the comments as well. M54B30 or M52B28TU?

@theylive8256

2 жыл бұрын

I would choose m52b28tu

@atnstn

Жыл бұрын

M52B28TU

@alexnljnpr

10 ай бұрын

@@atnstn why?

@alexnljnpr

10 ай бұрын

@@theylive8256 why?

Well done. I knew most of it, but still learned heaps.

@finessedyawife4915

2 жыл бұрын

What engine do i have in my 1999 328i. I know it has the zf 5 speed transmission

@aidenp5768

Жыл бұрын

@@finessedyawife4915 328i, your probably using the M52B28

What a legend

M52TU and M54 are identical engine blocks, only difference would be the timing chain cover that has the crank sensor on the M52TU and on the M54 is not on the front, but they are interchangable, so block is 100% indentical. I have made a M54B28 engine with 272/272 cams, ported and polished head, going to map and dyno it soon. Hoping for 270bhp. Only reason I went for b28 is shorter stroke, so I can rev it to 7300rpm, unlike the b30 where its 89.6mm and its gonna fall apart after 6800 rpm and tear apart the whole oil pump shaft and chain.

@crank3646

2 жыл бұрын

I was really thinking to try to make M52/54 with 300 hp, with cams like this + higher compression pistons and ITBs. But as usual, when you start doing your math, you are always going to say to yourself, just go with S54.

@michaelblacktree

2 жыл бұрын

Or put a turbo on it. 😛

@UndeadCrook

2 жыл бұрын

@@michaelblacktree Had a SC, removed it and sold it, prefer NA I6. If i want power would swap a N54/B58 and go for 600 easily.

@olegbelykh2840

2 жыл бұрын

@@UndeadCrook Do not polish and port the M54 head, you can't do better than stock. This is the silliest thing you can do with an M54 head without understanding how the M54 differs from the M50/M52. M50 / M52 are all aimed at reducing the fuel film in the intake, longer intake manifolds, etc. M54, on the contrary, relies on the fuel film as much as possible. The killer feature of the M54 is its excellent low/mid torque. This is achieved by using a fuel film on a specially shaped intake surface. Intake polishing turns m54 into m50 and loses low/mid torque. Yes, you pull out a little more power / traction at the top - but other things being equal, a ported motor will lose to an unported one in all conditions except for the only drag racing, perhaps ..

@UndeadCrook

2 жыл бұрын

@@olegbelykh2840 Mine is for track so I have custom 272/272 cams and having the power up top is what i need ;)

супер обясняваш и много информативно винаги исках да зная колко е по тежък м50 от другите 25кг не е мега голяма разлика

8:30 You are right. I have block m52 with single vanos, and it has sleves and also hole for the crank sensor.

@crank3646

2 жыл бұрын

Do you sell it :D

@robertbaca7131

2 жыл бұрын

@@crank3646 Nahhh, im building 3.0 from it :D

Nice video bro. What about the difference between the 3 versions of the m54? Is it possible to interchange some parts between them, for ex cylinder head?

@bnr_dett3826

9 ай бұрын

Im not 100% sure about the head but I believe you can since the m54 in general is the same engine what’s different from the B25 & B30 is the crankshaft,piston and rods they are different but interchangeable I also believe you can interchange b28 or tub28 internals into the b25 and or b30 m54

I had no idea the blocks for the M52 and M54 engines were so light

amazing

Nikaseal (sic?) was a development I believe by Cosworth for the Ford turbo engine in early 80’s

The M52 single vanos after September 1998 is with backside crankshaft sensor.

is there a difference in the number of exhaust stud holes? i’ve read that the m52 and maybe the m52tu have slightly less than the m54 which causes issues when installing headers

Браво ! Чакам с интерес всяко Ваше видео !

@crank3646

2 жыл бұрын

Добре е да има поне един такъв човек :D

this was great information, thanks! is there any advantage to the nikasil coating over sleeves? is it that bad for turbo? i wanted to in future maybe run low boost like 8 psi and maybe 300hp and thought it would be strong at that boost

@crank3646

2 жыл бұрын

Nikasil is better, no doubt about it. It provides less friction that the sleeves. 8 psi should be save enough for this engines.

@charlieward7606

2 жыл бұрын

@@crank3646 sounds perfect for me then, probably going to stay NA for now and good enough for a little extra in the future, plus the lightest block. thanks for the reply and videos!

M50 has best sound, M52/TU is most reliable and M54 has the most power.

@alexbabtan2395

Жыл бұрын

why ?

@samym4925

Жыл бұрын

M54 hat am wenigsten Leistung 😂 Die haben nie ihre Leistung

@haoshito5754

Жыл бұрын

​@@alexbabtan2395 materials and sizes

@cesarcantu9001

8 ай бұрын

M50 is more stronger for boost

@hoiheyhoi5343

8 ай бұрын

Yup i have a 325i 92 coupe nonvanos m50b25. Cold start damm sound is so nice. Its a summer car only drive it sometimes in the summer

where is it possible to find a guide on m50b20 oil nozzle install for pistons cooling? would be super usefull

Great Work thank you. I would love to see the m50b25nv head too. Is it true that single vanos heads have better flow then non vanos?

@NeverEndingBuilds

2 жыл бұрын

as far as I know its the opposite. The NV head has 1mm larger valves, so should have slightly better flow. As well as dual valve springs. So its a little happier with higher RPM

@EliasRizk53

2 жыл бұрын

@@NeverEndingBuilds what nv means?

@NeverEndingBuilds

2 жыл бұрын

@@EliasRizk53 Non Vanos (no variable valve timing)

M52TU has a better sound output than the rest of the engines and it makes great power too.

@moneyshifters

10 ай бұрын

the sound output would be nearly identical to the m54...

@Ayixlia

10 ай бұрын

@@moneyshifters No it's not, the M54 is a 3.0L engine while the M52TU is a 2.5L

@moneyshifters

10 ай бұрын

@@Ayixlia the m54 came in 3.0, 2.5, 2.2L variants. The M52TU came in 2.5, 2.0, 2.4 and 2.8L arrangements. Hope this helps.

Engine block on m54b30 and m52tub28 has the same part nr. Valves has the same part nr on m52b28 and m52tub28 but not on m54b30. Cylinder head has the same part nr on m54b30 and m52tub28 but I have seen differences in how they are machined both from remove part that are for casting and how the the inlets are machined. The inlets usally looks much smother on m54.

Ще направите ли клип за строук на м52 единиен ванос? До момента съм сменил входящия колектор с такъв от м50б25 и 2та изходящи от 25ца. Също така съм заменил 2та вала: M54B30 и M50B25nv. Трудно ги открих и намерих кой да ги намести, но за сега съм стигнал до тук. Преди финалното ремапване, какво бихте препоръчали за максимален ефект коне/ускорение на тази атмосферка? колянов вал и бутала какви да са? такива с които няма да има ганг банг на главата

For the S52 camshaft upgrade of M52b25 single vanos I need the 11311405051 and the 11311405488. Is that correct? And tray, lifters and springs of the M52 I can reuse?

And what about difference between M52B28 and M52B25 cylinder blocks alone ? Same stroke and difference is in crankshaft. So in theory I will make my 2.5 to be 2.8 by changing cranksahft and pistons ?

18:50 so I want to know, is it possible to install an M54/M52TU (double vanos) head on an M52 block. In the states the M52 block is iron and I want to turbo and still have double vanos.

Имам един въпрос възможно ли е на двигател m54 b22 да се сменят бутала и блок от b30 и евентуално по този начин да се дигне обема ?

What about the M52 Iron Block? I know you guys didn't really get them in Europe but surely you can get your hands on one!

Hi, I just want to know if the m54 engine brackets same as m50?

how about the camshaft Lift?, there is any difference between m52b28 and m52b28TU?

Cant put two likes 😔. I am planning to build an m50b20tu engine, but can I use m50b20nv block with m50tu/m52 head? Great video again! 👌

@crank3646

2 жыл бұрын

You can use NV or single vanos block with NV or single vanos head only. Double vanos block can use only double vanos head

@joshuam6828

2 жыл бұрын

If you’re that deep in the build, just keep your block and add NV pistons. They are beefy compared to the Vanos pistons.

I got the M52 TÜ would it make any difference if I just put a M54 Cylinderhead and Intake on It?

Greetings from Canada.. Great video you did good research... But I found a error in your video and wanted to bring it to your attention so you could add it to the description of the video for anyone interested...How do I know you ask?? Well I just did my oil filter housing on my dual vanos M52 1999 motor... It turns out there are 2 different OIL FILTER HOUSINGS ..Yes technically they do fit all generations BUT ... There is a version (as mine is) that has 2 SENSORS in the housing and the other version that only has 1 SENSOR in the housing.. So in a pinch it would work but you will lose 1 sensor... Again I enjoyed your video take care.. I ENJOY WORKING ON MY COOLANT SYSTEM EVER 6 MONTHS ...LOL.... BEEMER LIFE.

@crank3646

2 жыл бұрын

Yep but this is not an issue. Just use a hollow bolt on your Vanos supply hose, and you can add the 2nd sensor there. I will be doing this in my next video actually.

Hello, inquire, is there a difference between Crankshaft m50 m52 m54

So, if I wanna boost my car and make a casual 400hp, I wanna go with an M54 because of the stronger oil pump and the sleeved cylinder walls?

Може ли да се направи 2.6 от 20 ка само със смяна на коляновия вал?

I got an e46 323i (170Hp m52TU i guess) and im thinking to make an 3.0/3.2l Change. Is it possible? Maybe with m54b30 crankshaft, connecting rods and pistons?

@SupremeKai_Omniverse

Жыл бұрын

It Is

Hi just would like "Single Valves" vs "Double Valves" definition. Both have 4 valves per cylinder. Thanks for nice info!

@svetoslavshano

2 жыл бұрын

it is single/double VANOS which is a varialble valve timing system that provides low end torque

@tribleflip

Жыл бұрын

@@svetoslavshano good for top end power aswell.

@alexparrott6558

Жыл бұрын

Single vanos only has vvt on the exhaust cam and double vanos has vvt on both cams.

What is the advantage of having a "sleeved cylinder"? (you never told us)

Hello everyone i need some help ! So i have an m52 alloy block with m54 crank and forged 135mm rods and i wanna know if the m54b25 pistons fit? please help !

Прямо таки. "Лет ми спик фром май харт" ))))))))

what is the best way to get more power in the m52tub28? thank you!

@djahac

8 ай бұрын

m54b30 intake cam and intake manifold

Any US spec m52 single vanos has a crank sensor on the rear Also the US z3 2.8i m52 single vanos is an aluminum block with sleeves. (And a crank sensor at the back)

@crank3646

2 жыл бұрын

Everyone knows that US M52 engines are with sleeves, because of your fuel there. But in Europe we don't have that luck, so you are on the lucky side this time :)

Is the M54 and M50 working with the same pistons

M52 single vanos were steel lined in 99 this is distinguished by the rear mounted crank sensor

@lureknut

2 жыл бұрын

M52 got a technical update in '98 and is now called M52tu, one of the improvements is that it got double VANOS. The other improvement was steel cylinderliners instead of Nikasil coated alu.

@joseherrera5264

2 жыл бұрын

M54 has the crank sensor elsewhere? My (supposedly) M54 engine has the crank sensor at the bottom of the block.

Please compare the endurance or durability between M50,M52,and M54 engine block

@cosmingabrielmihailescu5318

2 жыл бұрын

Very simple, m50 is top, m52 and m54

Quel et le meilleur bloc moteur alors ?. Moi je dirais le M52tub28 328i double vanos le bloc n'a pas la même couleur que le M54 ??? Merci de m'éclairer 👍

M50, M52 is different in the USA. The water pump fixture is very different. All of these look like later versions in the USA, for example the S54 is similar but the opening for the water pump is different, and it does not feed up to the head so it is more like the versions you have as M50/52.

Hi how are you can we change m 50 engine into m52 engine without changing any electronics

is it possible to swap a m54 timing cover onto a m52?

Thank you very much for all this information. So if I want to build a M52B30 stroker, I have to use original M52 Pistonrings, to not damage the Nikasil, or should I use M52 Pistons with different Rods?

@tribewu3223

2 жыл бұрын

M52 iron block, m54b30 crank, pistons, and rods also b30 intake camshaft

@dikkodikko6262

2 жыл бұрын

@@tribewu3223 do you know if I can use the m50b30 intake cam on my m50b30nv? Using 413 ecu

@deepur2362

2 жыл бұрын

@@dikkodikko6262 You are talking about using the M54B30 intake cam for your M50B25nv Stroker? I dont see there any problems, if so there could be space issues with the vanos gear but you can disassemble the vanos gear from the intake cam. I'm using M54B30 intake cam on my M50B30 with MS41 and using the M50B20nv Intake cam as exhaust cam (B25nv cams are the same but mostly more expensive). Timings for intake cam are normal (using the common BMW Cam-timing tool) and exhaust cam is open 1.0 mm at TDC. I can highly recommend (rebuild) Vanos on M50B30 with MS41, never felt such a big difference with Vanos on any other M50/M52 engine. Really kicks when it changes timings at mid-RPMs.

@dikkodikko6262

2 жыл бұрын

@@deepur2362 i was thinking of that route. Do you have any social media platform that i could msg you on?

@deepur2362

2 жыл бұрын

@@dikkodikko6262 deepur91 @ insta

why did they erase the number of the cylinder block? Or it that a dodgy subject?