God bless this man for sharing his knowledge

@TheOldMechanic

Жыл бұрын

So nice of you, thanks 👍🏻👊🏻😉

I had the same problem with a two year old fluid, always changed in the BMW workshop. They admitted that BMW has recently changed type of fluid and the problem shouldn't reoccur ... Thank you very much for your videos. I also then changed the fluid, with the traditional method, but without using Motoscan for now.

You are 100% correct Sir. Love your channel. I have learned so much. Thank you. Randy

@TheOldMechanic

2 жыл бұрын

Thanks Randy ! 👍🏍

Had the same problem on my gsa f800 adventure and my mechanic said its moisture trapped and left sitting for long time makes it to split and set like slush... although I bought second hand from bmw garage amd I am not ruling out your conclusion on poor craft by authorised bmw dealer.. 🤪 thank you for your content 🙏

@TheOldMechanic

2 жыл бұрын

Hi Tata, I don't think its moisture because moisture makes the brake fluid brown. Just have a look at my playlist of the Honda CB500X, front brake fluid change. 😉👍🏻👊🏻🏍

I've always washed all the old crud and brake fluid out of the components with hot water. Since brake fluid is water soluble, cleaning with water and then blowing off the remaining residue with compressed air or wiping the water off of the components with a lint-free rag works like a charm. I've been doing this for over 45 years and have yet to experience any 'side-effects' from cleaning brake fluid with water. Just a suggestion......8^)

You can use a rubber band to pull the tabs to open the front reservoir.

@bjk311

2 жыл бұрын

Wanted to add the the videos and knowledge you provide is fantastic. Thank you

Hello Old Mechanic, like your video’s, very useful info they provide. Now, brake fluid is very nasty stuff, handle with care. But more importantly, any DOT (3, 4, 5) brakefluid is HYGROSCOPIC!! This means it ATTRACKTS WATER(VAPOUR) FROM THE AIR!! That’s what you found under the black cap, and even worse, IN THE BRAKEFLUID, that’s the white sludge (milky) stuff. It is water (condensed water vapour) mixed with the brake fluid. Like you said: DO NOT MESS WITH YOUR BRAKES, SAFETY FIRST, ALWAYS!! Because, water in your braking system and not to mention, the (very fragile) ABS system, will give you problems later on 100%! The HEAT that the brakecalipers generate will create WATERVAPOUR in the brake system! Vapour (gas) is like compressable AIR which you don’t want in the brakelines or ABS-pump. TIP: buy a brake fluid tester online, which you can stick in the DOT4 fluid container, they are cheap and very easy to use.

Exactly the same issue here …. Always DIY. Rear drive would be a great video to do :)

@TheOldMechanic

2 жыл бұрын

😉

I had the same stuff in my brand new zero km, 2015 f800r purchased in 2019. First job was blead the brakes.

@TheOldMechanic

9 ай бұрын

Its still strange, when i saw it I right away renewed that brake fluid, just like you did 👍🏻👍🏻👊🏻

Hello, the BMW manual would also provide for the caliper pistons to move back, probably to let out a greater quantity of old fluid. In your experience is this necessary? Thank you so much for your videos.

@TheOldMechanic

Жыл бұрын

You are right, actualy I should have done that Silvio

possible DOT3,4,5,5.1 mix and they did not like each other

Great video, just having bought a 2017 F800R a few days ago and going through it piece by piece I discovered the custard looking stuff at the bottom of both my reservoirs despite it meant to have been serviced! I have cleaned them out and bled them, the rear took 2 seconds, but I think I am having trouble with the front. Could you please give me some advice? I have bled the front callipers a number of times, and I cannot see any bubbles, the lever moves about 25mm and then starts actuating the brake to the point where the wheel will not turn, so the brake seems to be working and the pressure seems to be there, BUT!, the lever can continue to be pulled back to just about touching the grip, is this normal on these bikes? I bled both nipples at once using a Y piece hose, ( I used to use it for Guzzi Brembos with 2 bleed screws on each calliper); in your video you do them separately, would I be better doing them separately, if so does it matter which side first? I am waiting for my Unicarscan 2100 to come and once that comes I will also do a ABS flush as you described, could that help clear out any bubbles which may be sitting somewhere in the system and possibly causing the lever to get pulled back so far? Thanks for your help.

I've just discovered your videos - I love them. A quick question on this brake topic- My bike fell over and broke the front brake lever housing, necessitating a replacement. Can I replace the assembly and bleed the front brake lines as you do above? OR- Since I opened the system before the ABS pump, will it have to be bled as well? I just ordered the Unicarscan and dongle. Can you briefly outline my process? I am hoping to get a few more rides in before the snow comes.

Hi sir, from philippines i have trouble with my BMW F800GS the fan motor not starting when engine reach operating temp. Until overheat. I replace new sensor but still problem occur. Pls advise...

I had to SCRAPE the inside of the master cylinder reservoir because the BMW fluid had chrystalised. I wonder where else has chrystals stuck to it.

The BMW tool was only $20 when I bought it for my F800.

Always great videos! Is it possible it is disintegrating foam? My 1200gs has a foam pad in the reservoir.

I had the same case with my brake fluid. For me, this milky sludge has almost become a solid, something like a shell of wax. I wonder what was the reason that something like this precipitated from DOT 4 fluid

Dear Sir could you please tell me what level of moto scan do you use. Thank you, I appreciate your videos. Because of your KZread videos I have been servicing my R1200GS Adventure. Thank you

@TheOldMechanic

2 жыл бұрын

I use the Ultimate MotoScan app version (50 euro's) Greets

good video,great man

@TheOldMechanic

2 жыл бұрын

Thanks mate !

Possibly someone confused sauerkraut with brake fluid...an honest mistake, but bratwurst with dot4 ?

@TheOldMechanic

2 жыл бұрын

😂😂👍

I watched to see how you use the MotoScan app to do the ABS system. Maybe another video??

@TheOldMechanic

2 жыл бұрын

Hi Rick, when ever I need it for something else I will make a video about it 😉

I've been told that you can clean the pot with brake cleaner.

@TheOldMechanic

Жыл бұрын

Ofcourse you can Anthony 👍🏻👊🏻

Looks like mineral brake fluid mixed with normal DOT 4.

@TheOldMechanic

2 жыл бұрын

Someone said it could be a mixture of dot 4 and dot 5. And dot 5 you can,t mix with dot 4..!

Oops seems that I messed up, a lot of bubbles in the reservoir and the lever is hard as a rock + the stop red light is not activated - front brake is not working anymore.

@TheOldMechanic

Жыл бұрын

Hi Oscar, stay cool..😉. Are yoy sure that your front brake doesn't work..? It sounds so strange to me that your lever feels hard while your brake doesn't work you know.. Have you checked your ABS with the MOTOSCAN APP. ?

@TheOldMechanic

Жыл бұрын

These are the stuff you need for checking your ABS (and many more) THE UniCarScan UCSI-2100: amzn.to/3EUeUBe OR MX+ OBD2 Bluetooth Scanner: amzn.to/3GbxFB3 AND OFCOURSE THE SPECIAL CABLE: amzn.to/3VMLtrM HERE YOU CAN DOWNLOAD THE MOTOSCAN APP: play.google.com/store/apps/details?id=de.wgsoft.motoscan&gl=us

@oesda

Жыл бұрын

When scanned no abs error codes, when cycling the pump I do not notice any sound difference when the lever is pressed. Its weird.

@TheOldMechanic

Жыл бұрын

@@oesda hmm then I think that you keep on pumping new brake fluid through the brake lines as there is an airbuble trapped somewhere. Try to hold your bike so that the trapped air will automaticly through the highest point. Sometimes I am busy an hour or 2 to ket all the air out. Besure to keep your reservoir filled, orelse you start to pump air in the system again. IF that don't work you need a vacuum pump Oscar. Keep me updated !

@TheOldMechanic

Жыл бұрын

this somewhat the same vacume pump that I have, and for those problems its a good one and for not to much money too ! Vacuum Pump Kit for Brake Bleeding: amzn.to/3VtmERc