If you missed my last video where I build the gassifier used for this project, you can watch it here: kzread.info/dash/bejne/eoV9uZadhrnVm6g.html

@danielpiotrowski1681

5 жыл бұрын

Who would miss one of your videos?

@Nighthawkinlight

5 жыл бұрын

To bubble the water from the bottom to the top means that the gas needs to have enough pressure to force the water out of the tube. That's more pressure than my gassifier generates in this setup.

@unusualfabrication9937

5 жыл бұрын

silicone rubber is a thermal set, so it is pretty heat resistant

@fatihduran2110

5 жыл бұрын

I think a shower head hose might be able to survive the heat better.

@walkingdead171

5 жыл бұрын

You should make an airtight crockpot to heat the wood inside, leading to a canister to store the gas. Something I found online: Higher temperatures improve hydrogen yield in the gaseous product while CO yield decreases. Under nitrogen atmosphere, after 2 s at 950 °C, 76% (daf) of the mass of wood is recovered as gases: CO, CO2, H2, CH4, C2H2, C2H4 and H2O. Tests performed under steam partial pressure showed that hydrogen production is slightly enhanced.

Instead worrying about what type of tube you use , you could use a condenser to cool the gas before it reaches the tube

@robertwjenkins6916

4 жыл бұрын

I was thinking almost the same thing...just use a cooling system on the pipe and hose like the worm in a still

@Solnoric

3 жыл бұрын

And condense out tar that blocks it all up.

@kbee225

3 жыл бұрын

I'd say just run it though a water column. It'll cool the gas and also remove the impurities.

@stanwashighski3553

3 жыл бұрын

Absolutely correct! Coil condenser with a collection pot to capture contaminates at the bottom works very efficiently. I've used this method for years to convert acetone to diketene with great success.

@marshallscreekfarm3833

3 жыл бұрын

Isn't the condensed liquid diesel? so a diesel collector in the middle will prevent condensation in the pipe and melting the pipe.

I like how pretty much every by-product of this process is a useful material. The charcoal has lots of uses, the tar can be used to make wood rot-resistant, the wood gas is a decent fuel. There's really no waste.

@ChemEDan

Жыл бұрын

Charcoal ash can make soap, and the chemistry goes on forever

@MrRasZee

Жыл бұрын

and i can grow my own fuel . and it also grows naturally . just takes a bit of work thats all

@rubenskiii

8 ай бұрын

@@MrRasZeein medieval times people had dedicated parts of their forest for firewood, idk how it’s called in English but in Dutch it’s called “kreupelhout”. They had fast growing trees that they kept short and guided into growing many sidebranches, these could then be harvested yearly for firewood in the winter, and then next year the tree had made new branches that could he harvested. Saved people a lot of trouble, as they where usually close to the farmstead/village and no need to end the lives of trees just to get firewood.

@ianwise2457

8 ай бұрын

​@@rubenskiii sounds like what I'd call a wood coppice. That method of regularly harvesting wood can result in the roots and base of the tree living for centuries!

@rubenskiii

6 ай бұрын

@@ianwise2457 yes! That was the word i was looking for.

Everytime i watch videos like this i feel like I'm slowly preparing myself for the apocalypse.

@sethrenville798

9 ай бұрын

I feel like if enough people start using his ideas, we may evert the greenhouse apocalypse entirely.

We had three massive gasometers in my town, a few minutes walk away from where I live, they were a sort of landmark you could see for miles. I miss them oddly enough.

@sharmaskill

Жыл бұрын

Just one dude who’s way into gasometers

@fundelgurgel3913

8 ай бұрын

In my city in Germany they just got them a different purpose, they are now exhibition rooms for museums and a restaurant.

I like how you keep people from clicking away on your sponsored outro with your adorable bird

@NeonLightedDreams

5 жыл бұрын

Gabriel Schoene in a possessive context, it's 'your'*. Also I agree, that adorable bird prevents me from clicking away!!!

@gabrielschoene5725

5 жыл бұрын

Marcus Polus read again, I said your. You're right because you used your brain to realize your is the right word.. How about that there their they're word eh?

@NeonLightedDreams

5 жыл бұрын

Gabriel Schoene I'm looking right at it, it says you're! Also, I was trying to be helpful, didn't think I could write it any nicer!!!

@georgevavouras

5 жыл бұрын

Lol, he said both "your" and "you're" in the sentence.😂😂

@gabrielschoene5725

5 жыл бұрын

Marcus Polus I didn't intend to sound rude.. but I see it now. Not of the first your, the second your in the comment is incorrect.. good catch!

The look of pride on your face was so genuine in the intro :D

@andreasmayer6077

5 жыл бұрын

i love the proud smile during the burn at the end :)

@itsashepubg8967

5 жыл бұрын

AHAHAHAHAHAHAHA

@heritagekebek9979

5 жыл бұрын

Yeah! It was most effective than his last attempt with the aquarium ^^

@sodiumhypochlorite1196

4 жыл бұрын

He reminds me of my father

@callahanandews9893

4 жыл бұрын

Fr fr tho I said the same thing

His smile when he turned it on and it worked, priceless :)

Why oh why on earth would I watch any other KZread! 2 years it took to find you.. a $20 wood gasified camp stove brung me here. Thanks

7:05 the condensation is a mixture of wood alcohol (methanol), gasoline, tar and diesel. All of them are also valuable. You can set multiple filtration setups to collect them as well.

@sharpjk

5 жыл бұрын

how would you separate the four...also is the water in the gasometer tainted in anyway?

@Snix121

5 жыл бұрын

Fractional distillation

@BenjaminVestergaard

5 жыл бұрын

Could actually be harvested with some water-cooling of the pipes, perhaps a spiral chamber with an outlet, then the gas passed on to the gasometer will also be purer but of course also denser, so perhaps you'd need a spring or something to lower the pressure in there, basically sucking the gas in.

@Hellsong89

5 жыл бұрын

Tube with in and out connection, cooled by water, so it condensates to pipe surface and collects on the bottom as a pool, witch can then be with regulated flow valve let empty to container. Separation would be using standard oil industry techniques of fractional distillation as it was mentioned, where start product is heated and released to chamber. Due lack of oxygen it wont burn, but turn into gas. Chamber has several different levels with different levels of heat. Gasoline or methanol is easiest to turn to gas and will float on top chamber, where as heavier oils that take more temperature to turn into gas will condensate on lower levels, where these can be collected to separate containers, filtered again and put on use.

@gazzarrr666

5 жыл бұрын

I would consider 'cracking' the distillate while it's still a avpour by heating further over some kind of catalyst. That way you will get more gas from the liquid portion, so more yield of usable gas.

I absolutely love how simple and effective this is. Anyone and make an over-complicated solution to a problem, but it takes real genius to make something simple and elegant

@brucecowles9265

Жыл бұрын

Genius?yes sir and I bet you he read Tesla's Colorado note's-

That's so cool that you read all of the comments! I love how meticulous you are in your projects and how you're always showing where things didn't go as expected so we can learn from that too.

My goodness, you are really clever using the gas pipe. And using the epoxy to seal the bottom and the seam seal. Great job fella too.

WOOD -GASS POTATO CANNON!!!!WOOD -GASS POTATO CANNON!!!! WOOD -GASS POTATO CANNON!!!!

@richardgerbes7509

5 жыл бұрын

LedNek Crafting my good sir, I think your suggestion is by far the best comment on here...... Thank you.

@lednekcrafting5598

5 жыл бұрын

Richard G you are very most welcome

@CaptCorgi

5 жыл бұрын

Although I dislike all caps, I have to agree, "WOOD-GASS POTATO CANNON!!!!!"; Mighty fine Idea that one.

@trap9388

5 жыл бұрын

I was thinking that today when i first came across it, seems i wasn't the only one :p

@GOAT_GOATERSON

4 жыл бұрын

*GAS

Get some PTFE tubing. It's the most temperature resistant material that's flexible. You need specific connectors for it, but it will work up to 500F.

@Nighthawkinlight

5 жыл бұрын

Great tip!

@flavioleo1055

5 жыл бұрын

Or lab rubber tubing, a lot cheaper, from amazon or eBay is easy to find

@sparkyprojects

5 жыл бұрын

Silicone tubing would work You could put the inlet into the bottom tank, but you still need a small amount of flexibility A gasometer normally has 3 walls, the middle one being the top, the cavity is normally filled with oil iirc If you fill the main chamber with water initially, then when you get sufficient gas you could drain main chamber (bottom inlet would help with this), that would give you more room for gas, and lighter to carry

@SianaGearz

5 жыл бұрын

PTFE is not THAT flexible and not THAT temperature resistant, it starts to slowly give up around 250°C. Silicone beats PTFE on both accounts.

@USWaterRockets

5 жыл бұрын

PTFE is perfectly flexible and suitable for the application shown in this video. It will hold significantly more pressure as a result of the increased stiffness, which could prove useful if weight is added to the gasometer to compress the wood gas. Additionally, the melting point of PTFE is 327 degrees C compared to the lower 300 degrees C of silicone rubber. Either one is better than the vinyl(?) tube in the video.

A suggestion. The condensate is called wood vinegar and has many agricultural applications. Thanks for the work you've done to explain this process so well!

A really good system, producing two fuels: the gas and charcoal. Nice!

@professorfukyu744

Жыл бұрын

There's methanol being produced as well, hes just not collecting it.

You should try using the wood tar for something. Maybe make a 14th century ship with it. ;)

@gyrgrls

5 жыл бұрын

It's creosote. A few decades ago, it was used to treat utility poles, railroad ties, etc. Here in the USA, general sales of creosote was banned by the EPA in 1986.

@bilbo_gamers6417

5 жыл бұрын

@@gyrgrls damned epa

@ThatOneFriendlyDude

5 жыл бұрын

John Bond why was it banned? Just curious since I honestly don’t know anything about it.

@robertotarter7839

5 жыл бұрын

@@ThatOneFriendlyDude It's extremely carcinogenic. It's roughly thethe same as cigarettes' tar, just more concentrated, it'll give you all sorts of nasty cancers. Also, every kind of heavy metal found in low amounts in the starting wood will be concentrated in it.

@operator8014

4 жыл бұрын

@@gyrgrls Nastiest splinters you will EVER have in your whole life.

Silicone tubing is good to have around. It's short term temperature resistant to well over 300°C, long term to about 200. It won't melt ever, and if it starts to discolour, it's degrading or basically slowly burning up. Vinyl has a fairly high melting temperature... i forget... but it's a very hard plastic, so tubing must contain plastifier, which potentially has little effect on melting temperature but gets glass transition temperature way down. Incidentally this is why it's becoming softer when it heats up. At the start of the video i guessed that it would survive and hey happy that it did.

@TerminvsEst

5 жыл бұрын

Hey Siana! Singularity Viewer user here.

@bloodwolf2685

5 жыл бұрын

He needs stainless flex hose.

The smile in your face when lighting the torch - priceless :)

I am enjoying this video series. My late Grandpa and his late brother converted their car to run on wood gas here in Melbourne Australia during WW II to get around the petrol rationing problem. Back in the late 70's I can recall a couple of gasometer tanks near Heidelberg being dismantled as the town gas supply system matured.

His face so friendly, especially when he smile :P

@angkoonmethavee

Жыл бұрын

Agree

It's really awesome seeing you doing so much experimenting with wood gas. Like I said last time, try using ordinary trash, like paper, cardboard, cereal boxes, old rags, etc. as production fuel at some point. It may be a bit harder to use with your current setup, but I think it would be worth it to see how much gas you could produce from it compared to regular wood. And on that subject, it might be interesting to see how much you get from fresh wood compared to dead and dry wood. Also, bringing your adorable bird in to give us incentive to watch the sponsor bit of your videos is really clever, and I don't regret watching it one bit. I'd love to see an off-topic video just about your bird at some point. It's super cute, and it looks like you take very good care of it. ♥

@alaric_

5 жыл бұрын

I think the amount of wood gas produced is equal in fresh or dry wood, if the wood is otherwise the same. The potential for gas produced is not ruled by freshness, it just means it has more water. At least that's what i have always thought. Before the wood will pyrolyze and gasses will exit the wood material, water has to dissipate from it and that takes time and energy so the process is just slower. That could actually be a test in itself; how much dryness affects before the wood gas starts to produce.

@brucecowles9265

Жыл бұрын

And vinegar

Beautiful build. Many years ago, I played at my cousin’s house that was close to a coke plant. It was alway fascinating watching the gas storage tanks rise and lower, and I always wondered what was going on. At 70 years old, now I know. Thank you.

The smile, when you lit the gas, is contagious. Ty 🙂

Now you need to make it fuelled by a solar concentration lens so that you dont have to waste the wood to heat the fire, it can all go into making gas. Then you need to compress it and store it and run an engine on it.

@TheAnantaSesa

4 жыл бұрын

Or connect it to a furnace that is already going to be producing pyrolysis capable heat.

Braided steel cables (the ones meant for hot water hookups) or PEX (polyethylene cross link) tubing can't handle combustion temperatures but they are at least more heat resistant than vinyl and should have common links with standard plumbing fittings.

I don't know about anyone else, but this kind of stuff fascinates me. I can't wait to build one of my own. People like you need to be running this country. Take Care.

Your videos are my favorite to watch. I was inspired to make a storm glass using your methods and did so. I gave it as a gift to my dad using a nice glass jar that I found in a grocery store. Thank you for your for everything you do and i'm always excited to watch more of your content. Cheers from Seattle.

If you run your gas line in the bottom it can bubble up through the water to help clean the wood gas. It would also leave the top of the moveable sleeve unobstructed. In the late 80s or early 90s I saw an article in Mother Earth News. A farmer was running a methane digester with manure. He was using a similar gas collection device only massive. It was so big it had a pulley and counter weight system to make the inner bell neutrality buoyant. I believe his outer tank was concrete. I seem to recall it was as big around as a silo. With a system like that you could change the counter weight as a way to adjust the gas pressure.

im amazed on how dedicate you are, amazing job! you improved the desing a lot this time

Using that double walled pipe and end cap is brilliant! I was looking for a light weight solution, and this seems very suitable!

I really liked this video! You can get around the flexible tube by having your inlet and outlet pipes enter the BOTTOM of the water chamber, and then rise through the water into the headspace of the floating chamber. Gas will come in the bottom, rise through the tube in the water (or you could have it bubble through the water, but your gas generator would have to be above the water line) then it would either float the upper chamber, or pass out through the outlet pipe (depending on gas demand). This is the first wood gassifier that i have seen with any type of accumulator, and I must say, it has given me a lot of ideas!

@CarbonConscious

2 жыл бұрын

Great suggestion

I love the wood gas content it's fascinating how something so simple could be used for just about anything.

I love how you are able to make simple, easy to reproduce designs in your projects. You are my favorite KZread content provider!

Thank you for the heads up on the wood gas storage.

I’m so happy I stumbled across this channel, DIY on topics right up my alley.

You could put in a dirt pocket or drip leg (used in the piping trades) to collect the tar as it goes through the tube, then you could just blow off the tar and condensate to keep that tube from getting clogged over time!

I believe every single commercial should have the person explain the product while playing with a parrot in the foreground.

love the efficient water-seal below the gas.

That was the best design and explanation I have seen about gasifiers and a gasometer. Very well done! Thank you!

If you want fixed metal pipes you could just install a thin U shaped metal tube that goes down trough the water and up above it. It's essentially filling the tank from the inside, not trough a valve.

@rfldss89

5 жыл бұрын

I'm not sure how well that would work, since the pressure from the wood gas production would have to push the water out of the U shaped tube.

@Electroblud

5 жыл бұрын

@Rafael Dos Santos That's what it is doing with the current setup too. So it should be fine. I'd go with the internal tube.

@3karus

5 жыл бұрын

Rafael has a valid point. A long Tube surrounded by water will pretty much act as a condensator and collect moisture from the wood, just like the PVC tubing, but worse. Attaching a small reservouir at the bottom would solve that problem easily and with no big effort.

I loved how proud you looked when it worked.

Thank you for posting this informative video! Your system would be great for people living off the grid.

Nicely done. Thank you. Very informative.

As always it is great to see your progress and learning about this process, but best of all is your beautiful black headed caique, they are my favorite bird to ever have had as a part of my life.

Maybe you could add a three way connector with a collection vessel to recover the liquid that condenses out of the wood gas? It's going to be mostly water at first, but should also contain a variety of hydrocarbons and aromatic compounds (wood-tar creosote). These having low miscibility with water, they should separate and could in principle be easily recovered. Creosote is a cool substance, with some interesting uses, like treatment of wood.

@laharl2k

5 жыл бұрын

or also burn it if you atomize it like with kerosene or most oils.

@benjaminmiller3620

5 жыл бұрын

Terpenes as well if gasifying pine wood.

@johnjulie6657

4 жыл бұрын

A water trap.

@bobbaird8744

2 жыл бұрын

The brown liquid can be fractionally distilled to recover the methanol in it.

i like how you alwas seem so happy when you do things!! its like you not sure if it will work that just happy as heck it did!!

Wow, that burns cleaner than I expected. That system is worth refining and scaling up.

You're still My favorite DIY/Science Channel. Keep up the good work.

He always has a little smile. It's so cute, really brightens my day.

You look so happy. I'm happy for you. Great video.

Thank you so much and an amazing video. We have started our engineering project on alternate fuels and have taken this as a guidance. Keep it up. And thanks a lot

It would be a great idea to compress all of collected and filtered gas with an old refrigerator compressor or a modified bike pump (I've seen people making pumps out of pvc pipe that are able to produce more than 100psi) into some pressurised container for later use. Your low pressure container is great for collecting gas before it could be compressed

@tedf2

3 жыл бұрын

Compression rates are not good. I had the same thought. I found that a propane tank would only get a car 2 miles on the road.

@MrNeboff

3 жыл бұрын

@@tedf2 sad but true

@Solnoric

3 жыл бұрын

@@tedf2 either you used a little camp bottle, or your car gets 20 rods to the hogshead

@ellenorbjornsdottir1166

3 жыл бұрын

@@tedf2 dude what a 20lb would take my truck (petrol only atm) 20 km

@tedf2

3 жыл бұрын

@@ellenorbjornsdottir1166 I'm not sure what you're asking. But form the various websites describing vehicles running of wood gas it seems that the production of the gas was produced on sight directly feeding the engine. Also, the efficiency was equivalent to gasoline efficient vehicles, including transportation of the wood fuel. p.s. I'm no expert on this subject, although I'm indentured by it. Having said that, I don't think this is an alternative as a replacement of the gasoline engine i.e. "The Green Deal." There's just not enough of the feed stock around, just like ethanol. There are some plants worldwide operating on this fuel because they have a feed stock of waste from the products they harvest. Also FEMA has designs for producing wood gas for generators. but it's not meant as a replacement of the electric grid, rather it's to compliment it during emergencies when the grid is down.

I know this was part of my suggestion on the last video and apologize for the repeat. If you add a copper coil and an intermediate collection can right after the coil but before the tubing you will cool the gas significantly before it hits your tubing thus increasing its life span and you get the added benefit of collecting the condensate before it hits the storage container. Similar to how alcohol is condensed in a still.

@IonutJaR

5 жыл бұрын

cooper and brass can be considered as catalyst as well and purify the gas

@johnjulie6657

4 жыл бұрын

But the tar by-product would condense and cool within the condenser coils, whereby clogging the system and eventually causing a back pressure into the gasifier can... please tell if I have this wrong?

@MrNeboff

3 жыл бұрын

@@johnjulie6657 yes you are right , i had the same problem with ,mine . the solution was a cyclone filter and wood chips and shavings.

@dimesonhiseyes9134

3 жыл бұрын

@@johnjulie6657 a very low tech way of fixing that is putting a longer outlet pipe from the furnace. And taking a cue from natural gas piping place a T fitting with a pipe going down. Place a cap or preferably a valve at the end. Anything heavier than the gas will sink into the down pipe. Every now and then crack open the valve to empty it out.

I like how you can see the gas flow through the vinyl pipe, but I think a insulated hose like the type that goes from the water source to the toilet might work better and be easy to retrofit in your application. Great job!

Thanks that was very well done and a good insight tutorial. I can see some cool off grid uses.

Really like this series and can't wait to see what you have planned for the wood gas.

Dear NightHawkInLight, I have come up with a few cool things you could make a video on using wood gas. 1. Compress cleaned gas into a tank and use it in a grill or gas lantern. 2. You could run a small generator off of it and/or see how big of a generator it can power. 3. Make oil and purify it into gasoline/ diesel fuel. 4. Run a propane fridge off of the gas 5. It would be more work but a go kart running off wood gas would be cool. It could use compressed gas.

@ellenorbjornsdottir1166

3 жыл бұрын

I don't think a propane fridge will work. Any stove will though with an appropriate jet.

Great video! I'm currently conducting a research project on the potential of biomass energy around the world and stumbled on your video. How great to know anyone can learn how to make these things!

Why is it so satisfying to hear him pull apart the two cylinders at 1:49?

I really like your recent wood gas projects!

THIS IS QUALITY CONTENT...... Marvelous work.. bro .... And very educative...

Genius! And all with hardware store materials. My kind of video.

What a great video. Loved the simplicity. Brilliant sir!

5:18, the tube I would suggest using would be 100% Silicon. It should be rated for at least 450 F vs Vinyl Tube's 150-175ish F. It's also non porous so in theory it should be easier to clean all the soot buildup off of too. Oh and it's very flexible.

@rileymcdowell2889

5 жыл бұрын

TrollFaceTheMan could he also use some metal braided lines? He could probably get some at an auto parts store

@TrollFaceTheMan

5 жыл бұрын

Riley McDowell, good question there are two big factors I would consider with that. The first being because they are opaque it would be much harder to tell what is going on inside them so visual assessment of gas production would be impossible for the tubing. The other concern I'd have is though many are made to be rust resistant would the heat or even the byproducts like soot, methanol or things like potassium/sodium/calcium carbonate that accumulate over time in the tube affect that?

@IaCthulhuFthagn

5 жыл бұрын

Polymer tubing for laboratory glassware use, Tygon for instance, might be pretty good contenders as well, if a little more expensive, assuming one can strike a good balance between flexibility and resistance to heat and chemical attack.

I'm loving these wood gas videos! keep em coming!

You are the perfect choice for this task

Very beautiful process Thanks

I work with systems that measure exhaust gases from combustion engines. Those gases are hot and need to be kept at temperature to avoid condensation. To keep the gases heated we use so called flexible heated lines which use PTFE or PFA tubing inside, PFA being more chemically resistant (as far as I know). As you don't need to keep the gas heated, the tubing itself should be sufficient. It's not as flexible as vinyl tubing, but I'm confident you can figure something out.

@SundownMarkTwo

5 жыл бұрын

NightCaiqueInLight Bingo, new subchannel name for bird antics.

Fantastic work. You did a great job on this build and video!!

I did a lot of r and d on gasification back in the day and we used a much larger gasometer and gasifier. We had to stack lead weights on top of it to get the pressure to run a small generator.

Hi I'm Troy from Australia I'd like to say thank you im unable to work full time so I have little money I'm renovating my tiny home . every little bit helps . thanks you.

Cool video man! You might try adding a scale in inches with a permanent marker down the side of the inner chamber to help gauge the amount of gas being produced or used. It’s great to see that people are still interested in this kind of tech.

Not sure if this has been mention but a small heat exchanger before the tubing would stop any danger of it melting the tube I have used similar distilling lavender oil just a tube the same as the top tube with a water jacket fitted around it you can either have a pump set up to move the water around or just make a water bath and just top up with cool water occasionally to keep it cool. This is also a great idea for storing hydrogen from a solar electrolysis unit as well. Thanks for some great ideas

Stunning video, very informative and done with a great understanding. Well done !!

Thanks for your time. I enjoyed your video.

Please make a flamethrower with wood gas

@batenkait0s657

5 жыл бұрын

aaaand demonetized

if you inject it at the bottom of the gasometer wont you not need a flexible tube and just use metal since the bottom doesn't move?

@whynotanyting

5 жыл бұрын

You'd need an airtight seal around the space between the two tubes, but that might create too much friction.

@Grimidor

5 жыл бұрын

If you make two pipes go under the foot and enter the lower fixed container in the center; going through all the water and ending just after the waterline you could both fill it AND use the gas without any flexible hoses involved. Also without creating any extra friction between the cylinders.

@tonyhere7004

5 жыл бұрын

+1 First thing I thought of too Cut a small piece of copper pipe to reach the centre and just bubble the gas through the water. Bonus extra filtration too.

@user-jh3kz7dp2z

5 жыл бұрын

Grimidor problem with that is the top cylinder might be too heavy now

@MinecraftEAT

5 жыл бұрын

If you inject at the bottom the wood gas is also filtered through all of the water instead of just the water at the top of the tank

I'm very impressed. Bravo!

Ciao dall' Italia ,ogni volta che guardo questo ,mi piace sempre di più

the build is really informative. i have some ideas for improvements though like i didnt see a pipe leading into the water i dont think your filtering the gas all that much without it going into the water first. if you do put the pipe on it and you want the cleanest gas you can get i would recommend a diffuser of some kind at the end of the pipe which will increase the surface area of gas touching the water. i was looking for a way to contain some gases i intended to make soon i love this idea thank you so much for posting it i love your content.

I'm obsessed with this! I already make charcoal from willow on a small scale and it never occurred to me to catch the gas for later, could you possibly do a short video on a diy way to clean and condense the gas into methanol and maybe it's potential uses too? Thank you for all you do on this channel it's amazing to sit and watch through it all.

@peterpeterson7665

8 ай бұрын

Get a burner and use it to cook food/bbq

Nice job. I will try this on my next build.

Thank you for the knowledge

awesome job as usual, ben!

Those experiments are awesome, and I can't wait to see what will happen in the future, indeed 😍 About tubing, I know there are some kind of silicone pipes which are capable of dealing with some high temperature (up to around 300ish C, which is about 500ish F), so you should be able to find something (but I see also a lot of comments in that sense): but I live in Italy so I can't tell for sure where to find those things in USA (except something like ebay, amazon or similar) More than that, have you considered putting a longer piece of tubing (like 4-5mt/12-15ft) which a part is submerged in some cold water? This might help both with condensation and lowering the overall temperature of the outgoing gases.

Always enjoy watchin your videos this old tech will has ta start comin back tye way prices keep goin lol wonderful build to night o found an old metal fuel can an stuffed it full of shavingsan set it by the fire an took a broken broom handle an tookit to the band saw an stuck it inside the opening of the fuel tank an lit the smoke an my goodness it worked! Great video !!!

That was by far the easiest cleanest woodgas filter I've seen

@Nighthawkinlight

4 ай бұрын

Yep no filter beats giving the gas time to settle.

I think you can use a coil of copper pipe to cooling off the gas a little before it enter the plastic pipe? That way the gas will not too hot to melt the tube

Great video! I love your style of making videos! I am working on something really similiar for my oxyhydrogen generator. However, I am also trying to store it under a slight pressure by placing a 10 kilogramm weight on top of the tube, so that more gas fit's inside.

@Nighthawkinlight

5 жыл бұрын

Make sure that you separate the gasses and store them in separate containers. Storing oxyhydrogen together in a tank like this would be an explosion waiting to happen.

@vcokltfre

5 жыл бұрын

There are a few videos on youtube where people explain how people died because of compressed oxyhydrogen being so volatile and exploding

@Freizeitflugsphaere

5 жыл бұрын

NightHawkInLight Of course I know that, and I already made a lots of experiences with oxyhydrogen in the past. Storing about 5 liters is really no problem, its not that huge explosion, compared to other explosives. Seperating the gases using gravity works a little bit and reduces the amount of oxygen in the mixture, however, there is still enough left for a slow combustion. So I am going to find another way of doing it🤔☺️

@James02876

5 жыл бұрын

Freizeitflugsphäre it's pretty easy to separate the two gases if you're generating it through electrolysis. You use a wide basin of solution, and use separate catchment containers above the anode and cathode. You can even use two separate containers if you have a solution-filled tube connecting them. The hydrogen reservoir will need to be twice the volume of the oxygen one.

@Freizeitflugsphaere

5 жыл бұрын

James Petersen But thats efficient as hell

thank you for this information, I was thinking of how to do this too.

Same for methane storage, NICE work!

Not sure on other tubing you could use but if you extended the metal pipe after the 90 degree bend it will move your current pipe further from the fire and also let some of the heat the metal conducts to dissipate as well. Maybe extend it close to a foot but I figure any distance will help the further the better. Also what about letting a damp rag lay on the pipe for even more cooling would also help i would think

Well done! Thank you.

This is a perfect solution for camping stoves👍

5:27 well I have an idea.... Use steel wire reinforced cooking gas pipe.... It's flexible, heat resistant, erosion resistant, and air tight.... Easily available at dollar store

This is so awesome!

Have you considered doing pyrolysis of plastics? Add a condenser and collector before it gets to the gasometer. Then you can collect the flammable pyrolysis oil, and the equally flammable gas.

It'd love to visit this guy one day. It's be amazing to see all the stuff he'd built and have a stimulating conversation.