Best SLUGS for HDR 50 RAM. Make them yourself with BallMAKER Mold. Instruction & Shooting Test.
Спорт
New Slugs for HDR 50 RAM. Make your own ammo with BallMAKER Mold. Shooting Test on movie.
Shop with Molds:
BallMAKER.PL
Link to Molds on eBay:
www.ebay.de/usr/ballmaker2021
Пікірлер: 301
I ordered the .50 cal....these molds are very very good. I found that not only is the shooting fun but so is making u own ammo!!!! Great Product....thanks!!! Oh ya i went and ordered the 68 cal too.!!!!
@travisritter2152
3 жыл бұрын
So x,
@starsoldier3643
3 жыл бұрын
Not good for the barrel.
@hymlog
2 жыл бұрын
@@starsoldier3643 ...WELL...YOU ...CAN USE COTTON BALLS IN YOUR GUN!
@starsoldier3643
2 жыл бұрын
@@hymlog steel balls are not good for the barrel . the projectile needs to be softer than the barrel. Or the barrel will go out of round after several shots. Anything softer than the barrel is fine. They do make a solid steel barrel for this.
@hymlog
2 жыл бұрын
@@starsoldier3643....Once Again...You ...can shoot Cotton Balls out of YOUR GUN if this is such a Big issue for you! ..Everyone knows These types of guns are Not target guns.. ...(well almost everyone!)..
The most dangerous part of this video is that deck.
@AmenYeshua
Жыл бұрын
😂…thought so too 🤣
The impact of those 6 mm blank cartridges is insane. I'd love to buy those
A Nail tip that protrudes through the front of the slug and a Screw tip that protrudes through the front of the slug could be put in for a piercing projectile.
This looks like a whole lotta fun!
Love the 6mm blank rounds. 2 cool
Man, that 6x 4.5mm looks fantastic! Amazing job, keep it up.
Those rounds look fxckin ace mate 👍
Thank you, my German brother. Wonderful film. Greatly appreciated.
I ordered and hey got them to the states in like 3 days… Good dude, Highly recommend!
@roodymatiz
2 жыл бұрын
HdS 68 shotgun is next what you need have :) with ballmaker slugs it is powerful beast.
A BB behind the rimfire might be helpful in setting off the charge..
Pretty cool!
THAT POWDER ROUND COULD CAUSE SERIOUS OUCH. GOOD SHOOTING TEX.
Looks like fun
Obviously it's not meant to kill or incapacitate anybody *but* , with these bullets , a 20J mod (in the video is the 11J) fired inside a home (so 5-6 meters) I think this would be perfectly reasonable as a mean to scare a burglar/home invader that is not expecting you to have a ranged weapon and has a knife or barehanded. Obviously this is valid in countries like UK where 99.99% of the population, including the perps has no access to firearms.
@boomergroomer1996
Жыл бұрын
Home invasions typically involve multiple intruders relying on overwhelming their victims.
That blank slug would make an awesome Invasive iguana terminator, awesome video
wow i am impressed live and learn
Wow the 6mm blanks were the coolest. I think someone would expire getting sh*t with a couple of those. Really cool video 👍
Best slugs ever
Joy to the world....
You're a fuc... genius!!! 🙌🏻
Try putting some vics vapor rub on the back of the projectile, in pellet guns its called dieseling, generally adds 200 fps.
@midas7934
3 жыл бұрын
They sell power kits to increase these pistols to 16 joules, dieseling can damage the seals and shorten its life
@akimbofurry2179
3 жыл бұрын
@@midas7934 Do both, fuck the pistol long term, if you decide to use it for defens, get all its worth.
@midas7934
3 жыл бұрын
@@akimbofurry2179 to add to their and my previous comment, regular vaseline would suffice, vicks vaporub is just vaseline with eucalyptus, unless you wanna make your projectile minty fresh. Also i found that the kit upgrades it to 20-30 joules, i just ordered one myself. I would think that would be more than enough, dieseling could positively or negatively affect the accuracy also, testing before putting it to defensive use would be ideal. Although the owner of the pistol can do whatever they want, it is theirs afterall. The company that sells the kit, homedefence-24, also sells a sturdier steel barrel, i would think it would better withstand the increased pressure of the upgrade along with dieseling.
@lenm2857
3 жыл бұрын
@@midas7934 Dieseling works by compressing Oxygen and a fuel in an inclosed space (just like a Diesel engine). I don't see how it would work with a CO2 powered gun.
@midas7934
3 жыл бұрын
@@lenm2857 not sure, supposedly it ignites the petroleum based substance when you pull the trigger, but ive heard this confirmed from amateurs to experts. Ive also over lubed my crosman 2240 and it was much louder after a few shots and quieted down after that, didnt intend on dieseling it because i heard about it prematurely wearing seals, but it happened.
I’d use arrow blades make it so plastic sits up higher so arrow blade protrude out at point using a four blade System
THAT is pretty f%cking slick!
Dobry pomysł z tymi szorcikami
Anyone try using a bullet primer w/ a BB on the primer? using the hot glue as a binder/placeholder for them to sit BB in place for explosion on impact?
I have a suggestion : if you have access to a lathe , it would be cool to see how 12,7mm aluminum diabolos would perform 🙂🍻
@roodymatiz
4 жыл бұрын
Maybe in near future I or somebody Make it ;) Aluminium or Lead like original diabolos.
@Spiritof48
4 жыл бұрын
@@roodymatiz Oh yeah 👍 I’m ordering the HDR tomorrow myself , so that would be interesting to follow . Subscribed .
@FUCKDSS
3 жыл бұрын
@@roodymatiz I cant wait to see it maybe just some 50 call round lead balls
@cliftonhagan2397
8 ай бұрын
Gotta try some and some polymag 35 cal lol
Joli taf 👍✌️
i would like to use slingshot balls in steel to makke the same things..do you think it will working?? and how that you made the molls in rubber to put all those pellet balls with glue??
Thick but light nail in a more brittle rubber/plastic or softer (lighter & more malleable)hot glue, idea being the head of nail in the back keeping it semi-straight & giving tip penetrative damage. Thin but broken glass inside both tough & weak/breakable bodies.
@cliftonhagan2397
8 ай бұрын
Add rock salt. They will scream all the way home lmao
Did u formed the buckshots into Dual breaker? That looks sick
The BallMaker Is the top,I have the slugmaker.5012 but don't have the the hollow on the back!
@roodymatiz
4 жыл бұрын
With that slugs from ballmaker have better accuracy and power. It also have mushroom shape.
@madskaas5512
4 жыл бұрын
It is really amazing good .. they fly super good and fast ... wow mateusz boski .. u did a great job
I want to buy this one, can you give link for purchase? Do you ship to Hong Kong? Thanks
Does the round with a blank cartridge actually get any forward motion from the cartridge detonating ? Or is it just for sound effects and some 'mass' ? Thanks.
@elkesergl2691
3 жыл бұрын
You can literally see the exploding impact on the surface, which was the hit, u dumb?
Cool :)
You can actually get a sort of rifling on the slugs. Bumps up the accuracy and range a tad. I've been seeing some interesting designs with barbell slugs, too, but I don't think they'll work with this platform.
@petersmith6974
2 жыл бұрын
Home Defence-24 has a silicone mold for hdr slugs that has a spiral on the side of the slugs. I’ve just ordered one last week and awaiting delivery of it. A video of them is avail by Mad Dog air guns
Where to buy hollowpoints? (blank cartridge)
You could cast them with a polymer type casting resin.
@roodymatiz
3 жыл бұрын
Yes I have also silicon mold where I can casting polyethylen slugs.
@garettbodel3002
3 жыл бұрын
Now how do you compensate for cutting it in half do you measure the size of the blade. And then make your whole period or are you guys just going 50 cal and cutting it. Wouldn't it be like even with the band so I like a 16 to 1/4 of an inch after cutting through it because of heat
Hello. If you put Bangbang bigger, do you run the risk of exploding in the magazine?
Will a 120 wat hotglue gun work with it and will 10mm ballbearings work???????????????
Try nailgun blank ammo. It is much stronger.
I wanna see this in ballistic gel
You should try CB caps
Do you have links to type of glue used and slug mould/
Te naboje od chukowca odwrotnie wkładać żeby rowkiem uderzało. No i warto to wszystko wypróbować na różnych elementach, typu blacha, butelki, arbuz
I only have access to the 7 joule hdr50 (w/o mods, of course)- will that still launch a disc of Devastator rounds well, assuming the target is fairly close & the co2 is fresh?
@iyeetsecurity922
2 жыл бұрын
The 7.5 will shoot any ammo. Only difference is the distance/and penetration you'll get. I've gotten 185 grain slugs to shoot from it. I also made a mold from the aforementioned slugs so I can make my own similar to this.
Put a group of BBs in front of the 6mm blank
cant translate the ebay page. Im from the UK. Are you the seller
possible test a 4/5m Plz?
I would like to get a 22caliber pellet maker for making my own pellets how can I get one here in East Windsor CT
Is the blank based projectile hitting the target in two separate parts. Like a big tear in the target then a split second later a small projectile hitting ? Thanks.
@roodymatiz
3 жыл бұрын
This is 6mm flobert blank. It exploding when hit the target, but not always. It is less lethal ammo.
@jackspratt4343
3 жыл бұрын
@@roodymatiz Thanks for that.
Considering getting one of these for varmint protection while hiking. Think you could make a slug with rock salt work?
@roodymatiz
3 жыл бұрын
I don,t thinking about that, maybe a mix of salt, water and flour will be work... 😉
No se, donde conseguir ese molde
try phillips head drill bits
Try a BB sitting in a percussion cap. When the BB hits the percussion cap goes off driving the BB forward ! 😉
@roodymatiz
3 жыл бұрын
Thank you I will Try it ;)
@k12rising
3 жыл бұрын
@@roodymatiz post video!
Jakim klejem na goroco robic odlewy mozna jakis link do zakupu bo kupilem juz 3 i kazdy po wyschnieciu klei sie do rak
Niezle. Mam zamiar kupic ten rewolwer. Do samoobrony w razie W. Niezla robota z tymi kulkami!
@roodymatiz
2 жыл бұрын
Hej dzięki. Polecam oferty na Allegro, najtaniej.
Super filmiki dzieki 😄😄 posiadam hatsana at44.10strzelam troszke odpisz czy warto kupic hdr-a mozna go podkręcić prosze serdecznie za odpowiedź pozdro i git robota 😉😉
@roodymatiz
3 жыл бұрын
Czesc, myślę że wart kupić i zobaczyć jak tym się strzela. Pistolet ma naprawde potencjał lepszy od swojego młodszego brata HDP. Jak byś kupował bierz dodatkowe 3 magazynki. Na jednym CO tyle Ci starczy.
Jakim klejem na goroco to wyrabiac aby pociski po wyschnieciu sie nie kleily mozna linka
What you always could do is suck on some everlasting Gobstoppers until there's the right size and then shoot them out like riot balls if you even have to suck on them at all for the 50 cal. I did this for my 43 caliber Walther PPQ t4e pistol and it works great LOL I mean riot balls are extremely expensive and a box of everlasting Gobstoppers is like a buck 50 lol. Just let them dry first before you shoot them if you have to suck them down to size LOL. It works though...
can use for self defance
I WOULD LIKE TO BUY THE MOLD PLEASE AND CAN U MAKE A VIDEO USING MEAT OF SOME SORT!
@roodymatiz
3 жыл бұрын
Ok here is link: ebay.de/usr/ballmaker.oo
@roodymatiz
3 жыл бұрын
I would like test other new molds from ballmaker maybe using meat ;)
Anyone know where I can get an 11 joule version in the states???
I have a shit ton of 30 caliber Hilti shots why wouldn't it so often the gun and only go off when it hits the target wouldn't it go off in the gun what am I missing good anyways yeah I'd love to make one of those Terminator X. Hilti shot ammo
I’m getting me one so i can start making Ammo for this thing I’ll turn it into a stopping machine.
@GrimeSpreeStudios
Жыл бұрын
how did it go? what was ur best results
@cookinitmax
Жыл бұрын
@@GrimeSpreeStudios Man I never got me one . I decided not to go with that model or air gun so didn't get into making ammo.
Kanon kanon! 🙏
You use blank ammo for slug tip....don,t you worry about its geting explode inside ypur barrel ? Btw its exelent idea...whar about if you use ramset ammo for the slug tip?
@roodymatiz
3 жыл бұрын
No I don,t worry. It don,t explode in barrel because it is not behind of projectile but on front. And it is less lethal ammo, it don,t make big explode. But it can frighten bandit ;) I more worry always when I cast this slugs with blank ammo because temperature of glue is high.
Amigo donde consigo ese molde
How many joules is it?
Where to buy it
I'VE GOT A COUPLE BUT THE PENTAGON WOULDN'T LIKE IT NEITHER WOULD YOUR LOCAL LAW-INFORCEMENT. BUT I AM GOING TO GET ONE OF THOSE TOYS
@viceroyviceroy-wj7cf
3 жыл бұрын
if you live in the US just buy a real gun
Now, if I can fill my own ball rounds, like the pepper ball, but with CAROLINA REAPER DEATH SAUCE!
Do these types of slugs damage the barrel at all?
@roodymatiz
3 жыл бұрын
No worrie, glue is similar to rubber. And It is easy to clean if get dirt inside.
hellou what s the name of the mold, where do you prepare the ammunition? desde ya muchas gracias...!!
@roodymatiz
3 жыл бұрын
Hi, Yellow BallMaker Mold cal 50
Did this HDR 50 is 11 joules or 7.5 ?
@roodymatiz
4 жыл бұрын
11 J
Can these be used in the tr50 7.5 joule version
@roodymatiz
3 жыл бұрын
Yes, both 7,5 and 11J have the same charger.
Jakiego pistoletu do kleju na gorąco używasz ?
@roodymatiz
2 жыл бұрын
Róznie. Najważniejszy jest klej by się nie lepił po odlewie. Zauważyłem że biały transparentny jest najlepszy. No i olej silikonowy w sprayu jest ok.
Were can I buy the molding apparatus sir thank you
@roodymatiz
3 жыл бұрын
Www.Ballmaker.pl
they look scary! I'm afraid the devastators and not mentioning these once....
Hi! Can you tell me from where to buy this mold ball and little parts? Thank you!
@roodymatiz
Жыл бұрын
Ballmaker.pl or check description of movie. Little parts find in aliexpress or your local amazon.
What if you put a bb in front of the blank?
@roodymatiz
2 жыл бұрын
I don,t try.
THAT'S GONNA LEAVE A MARK
What size ball bearing should I be using here? & just confirming I along with the mould I just need a hotplastic glue gun to make these sluggs?
@roodymatiz
3 жыл бұрын
You can use max 8mm steel balls with yellow mold, with red max 9,5mm steel balls. You need hot glue gun for 11mm glue stikcs.
@skii76
3 жыл бұрын
@@roodymatiz thanks for that, so I should not use hot glue stick which is 12mm only 11mm?
@roodymatiz
3 жыл бұрын
@@skii76 if you have glue gun for 12mm sticks, that good. Use it. Use also good heating gun.
@roodymatiz
3 жыл бұрын
@@skii76 Glue sticks 7mm will be too small. 11-12mm are good.
@GrimeSpreeStudios
Жыл бұрын
@@roodymatiz if this was for the 68 cal would a 50 cal BB be a good choice? I was thinking a dart head coming out the top would cause massive damage ( to non living targets obv not intruders as in my country the burglar is the victim ) if they try break into your house u should let them take ur stuff BUT warn them your calling the police because that wont wind them up more n more n potentially kill you.... its a joke over here
Is this available to ship to california?
@roodymatiz
3 жыл бұрын
Yes, check link to ebay in desription of the movie.
Where can 8 buy the multiple round slug
@roodymatiz
3 жыл бұрын
here you can buy molds: ebay.com/usr/vimat.forms
By making that concave in the back we should fill it with Vaseline and it will diesel
how powerfull is your gluegun, some people saying the glue not heating up enough
@roodymatiz
4 жыл бұрын
100-250 W, 220 oC also if gluegun heating too much it can glued mold too much even you grease mold.
Try using wax instead of glue.
Hi where to find slugs with 6 mm blank cartridges?
@roodymatiz
2 жыл бұрын
Hi, you can make your own. Selling that slugs is propably illegal in a lot countrys.
HAllo, du machst 6mm Knallpatronen rein ? kommt da ausser Kleber noch was rein Kugeln als Schlagbolzen? Gruß
@roodymatiz
3 жыл бұрын
Write to me in english language.
@joergkoetzle2987
3 жыл бұрын
@@roodymatiz Hello, you put 6mm popping cartridges in? does anything else come in as a firing pin besides glue? greeting, Google Translator
@roodymatiz
3 жыл бұрын
@@joergkoetzle2987 no, nothing else, cartridges blow when they hit the target.
How many shots per fill cylinder?
@roodymatiz
3 жыл бұрын
24 shots, 4 charges on one CO2 but last six shots with low power.
What if I made hypotetically thise slugs from aluminium
Can you shoot a canned ham or tuna or maybe a animal head, such as a cow or pig head, from a butcher shop?
@roodymatiz
3 жыл бұрын
On Spring maybe I will try.
take care not to ruin your barrel inside, the cinetics are different even with similar materials and slightly different size, but with different shape its risky
@roodymatiz
3 жыл бұрын
Barrel is flat it is straight pipe. Hot glue is like rubber these both have similar softness... i don,t make slugs with parts of metal which they could scretch a barrel. ;) Also glue can easy clean from inside the barrel.
@michaelfinch1829
2 жыл бұрын
@@roodymatiz So if I made 12mm long bullet shape projectile with a sharp tapered tip on a lathe out of stainless steel, would it work and be similar to a real bullet?
What size gold points do I need tor t4e .50 cal.. 9mm or 10mm?
@roodymatiz
2 жыл бұрын
9x7mm (9 wide× 7 high)
@thefinalsay8330
2 жыл бұрын
@@roodymatiz thank u
Bom dia...onde posso comprar esse kit pra fazer as munições? Procurei aqui na net e n achei vc pode mandar o link?🇧🇷🇧🇷🇧🇷
@manfredohunterberger2403
Жыл бұрын
Brasil tá difícil amigo. Da pra importar, acho, da "homedefense/24", mas aqueles moldes não produzem estabilidade, quem de caros. Tem que ter o ôco no fundo como esse molde do vídeo. Também queria..😅
@lregobrasil439
Жыл бұрын
@@manfredohunterberger2403 🤝
can you please make one for .68 cal im begging you please!
@roodymatiz
3 жыл бұрын
Check link in description I sell a few kind of mold for .68. And are awsome :) 👍
@roodymatiz
3 жыл бұрын
Check other movies on my channel.
You can sharpen a nail and put it on the tip i saw a guy shoot nail darts out the shotgun one.😳
@roodymatiz
3 жыл бұрын
Charger is too small to put long nail.
@hymlog
3 жыл бұрын
....Good for You ...You Get A Cookie!
is possible to make explosion?
@roodymatiz
3 жыл бұрын
if you put blank cartridges from blank gun to balls ;) then those balls make a lot of noise and holes in cartboard
Where can you purchase the molds
@roodymatiz
3 жыл бұрын
Ballmaker.pl