This was helpful. I am a newer quilter and I am learning so much watching you. You explain and demonstrate very well. Thank you for sharing this with us 🎉😊.

@CarolThelen

5 ай бұрын

My pleasure! Thanks for watching and sharing.

You are an excellent teacher. TY so very much.

@CarolThelen

5 ай бұрын

You are so welcome!

Carol....you are a legend! Big Hugs from New Zealand :))

@CarolThelen

5 ай бұрын

Wow, thank you! Hugs to you too!

Very good tutorial on HST units.Thanks Carol for sharing. 👍❤️🙂

@CarolThelen

5 ай бұрын

You are so welcome!

TY for sharing this information with us. I have been learning so much from your vlog. Looking forward to the next one every morning.

@CarolThelen

5 ай бұрын

You are so welcome!

Hello once again, as l have said before, l have learnt so much from you and l am still learning! Kind regards from Melbourne Australia 🇦🇺🦘🥹

@CarolThelen

5 ай бұрын

Many thanks!

Don’t forget to starch and press before cutting. It helps keep the bias edge from stretching.

@CarolThelen

5 ай бұрын

Oh yes! Thanks for the reminder. I do that nearly every time but often forget to mention it. Thanks for watching.

Thank you for these tutorials. I always pick up something new each time. Very helpful and clearly presented. Thanks again

@CarolThelen

5 ай бұрын

You are so welcome!

Thank you for the video and the charts. I love using my Accuquilt for triangles even if I need to cut them down because I don’t have the right size. However, sometimes when I want only a few triangles, I have to take the time to look up the information on the size to cut them. Now your chart will be in a folder near my cutting mat. 🙂

@CarolThelen

5 ай бұрын

Great idea! Thanks for watching.

For those of us who are not lucky enough to sew everyday, these are great reminders even if we are not exactly beginners. Hope you do a lesson on “ rectangular triangles”. Never sewed these but want to. I understand these can be tricky. Thank you for any consideration of this request. (KH)

@CarolThelen

5 ай бұрын

Thanks for the suggestion. I'll put them on the list! Thanks for watching.

@CarolThelen

5 ай бұрын

I was thinking about this and remembered I do have some videos on this. I'm not sure which shape you are asking about but here are two different ones: Half Rectangle Triangle - kzread.info/dash/bejne/mYCerKmJf8u6lLw.html and kzread.info/dash/bejne/qnyp29lsiJXbkrQ.html Triangle in Square (Tri Rec) - kzread.info/dash/bejne/qY542ZKyk9LUg7w.html and kzread.info/dash/bejne/e4qmyMeYj5TgaZs.html I have found no other accurate way to make these than to use a tool to cut them, especially the Tri Rec units. Hope this helps!

@davidhatfield5714

5 ай бұрын

Thanks for your reply . I went back and found your block that I think I was trying to remember..0704 1/2 rectangle tri angles. I’ll watch it a few times. You are one of the best teachers..so thank you again.@@CarolThelen

Thanks again! ❤

@CarolThelen

5 ай бұрын

You are so welcome!

Great video as always

@CarolThelen

5 ай бұрын

Appreciate that Thanks for watching.

Great tutorial today, Carol. Thank you so much! ❤😊

@CarolThelen

5 ай бұрын

You are so welcome!

I think I will go to the full inch and trim down, especially if using a full 1/4 in.

@CarolThelen

5 ай бұрын

I agree. That method is easier to cut and to piece and is always accurate! Thanks for watching.

@sandybruce9092

5 ай бұрын

I also need to go the full inch j stead if the 7/8” - I’d rather have to trim just a tiny bit and have it correct, l,us my winky eyes work much better this way! I have don’t it the 7/8” way many years ago - I now have quite a few HST that ended up slightly too small for that project but I’ll find a use - eventually😄😄. Great program!! I’m always ready for a reminder!!!

@CarolThelen

5 ай бұрын

Thanks so much for watching!

❤