Be Ready For Any Power Outage! DIY 3000w SunGoldPower - PowerQueen LiFePO4 Home Backup System!
Ғылым және технология
Are you wanting to be prepared for future power outages? By going with a simple DIY battery backup you can keep your appliances running even when the power goes out! If the outage is long term you can even charge up your batteries using solar panels! This was a fun project that used very little components. Check out the parts list below.
MAIN COMPONENTS:
3000w SunGoldPower Inverter Charger System: shrsl.com/3w1ix
100ah LiFePO4 Batteries: shrsl.com/3w1j7 OR amzn.to/3J3IisC
Harbor Freight Rolling Cart: www.harborfreight.com/30-in-x...
OTHER PARTS AND TOOLS:
5 Ohm 10 Watt Resistor: amzn.to/3HjdbYM
WindyNation 1/0 Copper Wire (5ft): amzn.to/3Xp3rBX
Hydraulic Crimping Tool: amzn.to/3wlKqnO
5/16th Copper Lugs for Wiring: amzn.to/3XMlWjB
40 Amp DC Circuit Breaker: amzn.to/3ZMvZH8
Aluminum Rail for DC Breaker: amzn.to/3ZGRxoq
XT90 Connector for Solar: amzn.to/3D10BuG
10ft 30 Amp RV Cable: amzn.to/3GOrcw6
6 ft AC Charging Cable: amzn.to/3kw8H8f
Digital DC Clamp Meter: amzn.to/3CX5i8D
The use of affiliate links provide a small commission for me when you use them. Thanks for supporting my channel content and allowing me to do future comparison videos! More videos coming soon!
Video Timestamps:
Components and Cost: (0:00)
How is it built?: (2:30)
Testing the Inverter: (7:23)
Charging Demos: (11:35)
Final Thoughts: (12:49)
#jasonoid #solarlife #solargenerator
Пікірлер: 329
You're always so good at thoroughly explaining everything! And making it look so simple. Thank you, Jason.
Very good video. I built a 12 volt system like this about 2 years ago using a cart from Harbor Freight. Makes it nice to be able to just roll around the diy solar power station.
As a mechanic, for 20 years. Then a commercial electrician, it kills me that just about every KZread influencer hooks up battery's backwards. Remove Negative first, and install Negative last. That way you have no chance for that spark, or an explosion in your face. No resistor needed. I have seen so batteries explode, and injured people. Yes from lifpo-4!!
love the cart setup. an alternative to the resistor is to put a filament light bulb in series on the positive lead when connecting the battery. also there are a lot of 240vac output ups solar inverter chargers. to use one of those you'll have to add a split phase or center tap transformer, but you can get from the ac output lower amperage while delivering the same amount of power.
Love the setup, definitely a life saver for any emergency...well explained great channel....!!!
wow.. thanks for the tip about the resistor.. really appreciate it.
Thanks! Hi - I wanted to thank you for all your help. Thanks for being a team builder! I have learned a lot and it has saved me a lot of grief and dollars!
@Jasonoid
Жыл бұрын
Thank you so much, Katy!
NICE! Rule #1 Nothing is EASY! Some suggestions for safety IMHO to prevent a fire (these things HAVE caught Fire). HEY! it's YOUR home. Think AC panels here. A Main disconnect switch of the proper size at the source (that big battery is the source here). THEN a fuse or breaker of the proper size to carry your load and protect the WIRING within 7 inches of the battery POS post (REQUIRED on a commercial unit I believe). Do maintenance checks often and keep connections clean and TIGHT. Could it pass an inspection? HEY! WHAT CAN GO WRONG? Insurance have disallowed claims because of these things. Do it RIGHT don't just make it work!
I built a system very similar to yours but I used a cart made of composite material that is non-conductive. I enclosed the battery storage shelves with chalkboard material bought at Home Depot for under $10 each. I cut them to cover the sides and back of the open areas pf the cart. I secured them to the cart with strong Velcro. This will prevent items getting into the battery area. I do not have insulated tools, but I do cover the tools I am working with in heat shrink tubing.
Thank you for sharing. I am looking forward in creating my own system.
Very informative. The fan noise would quite down if you hung the unit on the end opposite the handle thus having top to bottom airflow. That would also free up the top shelf.
Hi Jason, I really love your canned food setup in the back. Looks like it's setup so you can see the dates on all the cans.
@Jasonoid
Жыл бұрын
I made a video about it AWHILE back, you can see it here: kzread.info/dash/bejne/moeOkqqhY9jYprA.html
Another great job and video. Thank you for taking the time and sharing the info. God Bless.
Cool idea, however your fuse amp rating needs to be smaller then the amp rating of the cable. Also solder on cable going under a screw isn't good practice. But well done and good work.
What a great tutorial and super neat build. Really interested in that transfer switch and glad to see you also have a video on that. Will be watching that next. :) Cheers from Chiang Mai, Thailand.
Great build on the modular setup. Power stations are great but these can be fixed or parts swapped and more. Great for the person who likes to build there own..👍🏼 The sparks 🧨 were great to 😅😉
@Jasonoid
Жыл бұрын
Totally agree! Upgrading or adding batteries is EASY with a setup like this.
I'm just getting started in my solar journey and I am looking for informative videos. I like your presentation style. It moves fast, covers the subject well. I appreciate the matter of fact approach. You speak clearly without stammering or pauses. I subscribed and liked. Well done.
@Jasonoid
9 ай бұрын
Glad it was helpful!
This is one of my favorite diy build videos. Well done, thank you. I'm jealous of all your backups btw. Subscribed, bell rung, commented, upvoted, liked, shared ... may the algorithm gods smile favorably upon your channel friend.
@Jasonoid
3 ай бұрын
Thanks! :)
What up Doe!? I really like that all in one setup with adding 4 batteries Dr J' 👍🏻👍🏻
Excellent thanks Jason 💐
This is a fantastic video. The info you presented was just outstanding. Very good learning
@Jasonoid
Жыл бұрын
Thank you very much!
Great video, I just made a video with my slightly upgraded setup, still 12V... i want to go 48V soon. your video helped explain some of the aspects of it. thanks!
I own two Bluetti AC200P's, Echoflow Pro, and an off-brand 2000 watt solar generator plus I have 2820 watts of solar input. My solar generators are usually fully charge by around 12:30 pm. I live in Golden Valley, AZ with around 300 full solar days per year. I have excess solar charging capacity on most days. I like to tinker around with stuff. So, this gives me some ideas for my next project. Thanks for the video!
Nice informative video. Thanks for sharing and giving us lots of details on this.
Excellent video as usual!
I think it's totally awesome!
I love the Rack to the Right with the Preps. I see your Prepared. I have a similar setup myself
@Jasonoid
Жыл бұрын
I was thinking of doing a simple preparedness video. It's good to have food, water, supplies, and energy stored up :)
@Moes_Prep_and_Tech
Жыл бұрын
@@Jasonoid you should, the same kind of people interested in Battery backup will probably have a backup of food stashed away. If I had the means to make a Solar Powered Emergency Bunker I would, lol
@Moes_Prep_and_Tech
Жыл бұрын
@@Jasonoid I have a room in my house I don't use, every time I take a trip to the store I get a couple extra things, little by little without making it look like I'm hoarding
@Jasonoid
Жыл бұрын
@@Moes_Prep_and_Tech that's the way to do it!
Awesome video. I wish I seen it sooner. I’m now to far into my 12v system to make the switch. No pun intended.
I used that same cart for a build I did about 4 years ago using Tesla modules. 👍
Excellent video. Great information.
Excellent video. I have a Delta mini but I think I will build one of these also because I can always add additional batteries later on.
@Jasonoid
Жыл бұрын
Glad it was helpful!
Great video! Was looking to something similar l but with the MPP 2724, but I can see the versatility of using a system that plugs directly into a transfer switch.
@Jasonoid
Жыл бұрын
With a system like this you can take it with you to the next house :)
Excellent ideas. Nice to DIY and have a purchased solar unit. Caution with the metal cart 💥
@Jasonoid
Жыл бұрын
Short circuit = BOOM! haha
Great video!! Awesome idea! I am going to copy your system. Thanks for sharing your build!!
You are a great teacher....
@Jasonoid
Жыл бұрын
Thank you! 😃
Thank you! 5ohm 10 watt resitor those huge sparks are always adrenaline dumps😊
Great Video Thanks Jasonoid!!
@Jasonoid
Жыл бұрын
Glad you liked it! Something like this will work great for grid instability.
Very great build Quick background, im a marine electrician, and design and install systems on boats like these One thing i would recommend is using a class t fuse for the inverter We’ve seen anls break and then re-weld themselves back together and cause a fire But beautiful system!!
@Jasonoid
6 ай бұрын
Thanks for sharing your experience, that's helpful!
Looks like the one silver Stacks Prepper made. Nice 🙂
@Jasonoid
Жыл бұрын
I haven't seen his channel before, I'll check it out!
Very nice! Thank You!
Thanks for your video, great as always. Wondering if you could do one explaining the pros and cons of 12V vs 24V vs 48 and break down where it would be most beneficial.
@Jasonoid
Жыл бұрын
Great suggestion!
@equanimousawareness
Жыл бұрын
48 volt is more efficient than 12 or 24. The more voltage step-up the more power is used just for the step-up process. When using a 220 split phase inverter to power central AC unit or other 220 appliances a 48 volt system is pretty much a must.
@robertsmith2956
6 ай бұрын
@@equanimousawareness If all your doing is keeping the fridge running, 12 or 24 volt is better since the inverter doesn't eat as much power sitting around waiting till it needs some energy output. The 48V split phase eats more power if the AC doesn't turn on.
Can you connect the ac output to the wall plug to run all the house power And also connect the ac input to wall outlet to charge the battery when the power come at the same time ?
Awesome video
@Jasonoid
Жыл бұрын
Thanks for checking it out!
@VinceBadovinatz88
11 ай бұрын
Agreed 😊
@johnfitbyfaithnet
9 ай бұрын
Agreed!
Stand your inverter up cause heat rises and it rising up into the electronics whilst laying on it back. Great idea and I love that you didn't hide the prices like most people do. I'm looking to do this with a 5kw 240v hybrid growatt to power my house as I'm exporting 20kw a day back to the grid yet still have to but power everyday .
awesome build👍
@Jasonoid
Жыл бұрын
Thanks for checking out the video, Mike.
I like the thinking outside the box. We have come to be reliant on plug and play, if a single device i.e. solar generator fails, or your generator fails, you are SOL, this has its place. Single items can be replaced to restore the system. Having said that, I am a huge bluetti fan, I have AC200max with 2 b230 batteries. I have 2 EB70 and 1 EB55 in 220v versions. I have spare cables and spare power supplies. But always looking for other ideas. Great video thank you.
Thank you once again. 👍🐝🌞
@Jasonoid
Жыл бұрын
You are very welcome
I happened to be watching while on Bluetooth to my home theater receiver with Klipsch dual 12 sub. When you connected the battery to the inverter, the floor shook🎉 😂
@Jasonoid
11 ай бұрын
Heck yeah! LOL
Nice one bro
Wow, this is almost what I'm working on in my basement! I saw Survival Lily use a cart in a video a while ago, which I thought was a wonderful idea, and now you. 😁For what its worth, on mine I am using 4x 100Ah batteries that just fit on the bottom shelf. (I used a piece of 1in thick insulation board under the batteries to cover the screw heads for the casters and the ends of the screws holding the uprights.)
@Jasonoid
Жыл бұрын
Four 100ah batteries is probably the best way to go, then you can pull the full 3000 watts.
Good stuff 👍
I've always liked the component systems. I guess this is a hybrid component system. I am impressed. Are you going to put the add-on WiFi connection on it? Great concept of the HF cart. Thank you for a very good video Jason.
@Jasonoid
Жыл бұрын
Thanks Kevin! I like how it has the option for the WiFi module and I have thought about adding that for convenience. I'm just hoping this project is an idea bed for others looking to do the same thing.
Great video on "Energy"! As an outdoor enthusiast and RV lover, I highly recommend checking out the Segway Portable PowerStation Cube Series. With its massive capacity, fast recharging, and waterproof technology, it's perfect for powering all your devices and appliances during camping trips or in case of a power outage. Plus, the Smart APP Control feature adds convenience and peace of mind. Definitely worth considering for your outdoor adventures!
all in ones are for sure the way to go when it comes to solar input and battery storage cost if you dont need to be mobile.
@Jasonoid
Жыл бұрын
I agree, it's super simple to put together! This one is KINDA mobile with the wheels, but nothing like a portable power station haha.
Great video and I've done a similar setup with a cart in my garage so I can bring power where I need it in my driveway. If I would do it over again, 48v all the way.
@Jasonoid
Жыл бұрын
Yeah, 48v system with server rack batteries!
@MattLesak
Жыл бұрын
@@Jasonoid like you, I wanted to use what I already had on hand and it worked out. 48v would be ideal just from a wiring perspective, especially with the array you have in the driveway.
Great video! I just recently found your channel and have really enjoyed your clear and concise presentation. I am really considering this sungold inverter. Quick question- how big of a battery bank can this take (e.g how many amp hours)? Thanks!
@Jasonoid
8 ай бұрын
As big as you want! I had 400ah connected before and it worked like a champ!
I bought the 24v kit. The issue I have run into is delayed shipping. They didn't inform me most of the kit is in background. The other issue I ran into is I did manage to get it put together and the batteries won't charge. Tech support is really slow to respond.
I was wondering how you wired your transfer switch. The inverter output is 120V AC. So you can't wire with 120/240 split phase. Did you just use a jumper off the hot to power both bus bars with 120V? Seems like that is the only way be able to use all six breakers. Thanks.
@Jasonoid
9 ай бұрын
It's a 120v transfer switch. All circuits are powered by one 120v leg. If it was a 240v it would require two hot legs. They offer many different models.
Enjoyed your presentation and certainly a modular, DIY approach to home backup power is in many ways superior to off the shelf products. I forget, was there a monitor for battery SOC in your set up? For camping (and home backup), I built a 12 V 100 ah battery with MPPT charging, various connectors, a charger and a small inverter and find that an EcoFlow Delta 2 does the job better in a smaller package. However, if anything goes bad on the Delta I can’t really know what has gone wrong and will have to wait weeks sending it in for repairs, etc . With a DIY unit, you have more options. Did I mention I really enjoy your videos?
@Jasonoid
Жыл бұрын
Thanks Jack! The SOC is kinda tracked in the inverter on the screen... It's not amazing though. I think the portable units have their place, the Delta 2 is so lightweight and compact. It certainly is one of the best current options for a 1000wh device. I personally enjoy DIY and off the shelf options because both have advantages.
Love this setup. Would you consider doing remote consulting for a fee to help me on a similar setup?
One thing I would be a little weary of though is tinning wires before putting them in a compression style connection like that. Probably will be fine though. Nice video!!
@Jasonoid
2 ай бұрын
Thank you, I learned that after posting this video.
Any chance you could do a current remake since prices are cheaper. I'm looking at doing this for an emergency system (with Victron items) Love the videos as always
This is great. I was just talking to Ask Ive Solar about a very similar setup as an alternative to a powerstation. Though it was using an EG4 version of this and server rack batteries. Did you consider the structural foam carts? They are the same though they might not have the middle shelf. I like that a system based on an all in one tends to have a lot more charging amps, wider voltage range, and programmability. I am trying to figure out home assistant right now so I can make my EG4s turn on AC charging when the forecast and my weather station confirm poor sunlight.
@Jasonoid
Жыл бұрын
I think for someone looking to build a 'future proof' DIY setup, 48v is the only way to go. I LOVE those 48v LFP server rack batteries! Eventually I want to have a system like that in my home, it's just a fairly large investment. Adding a smart capability would be really cool! Just make sure you purchase UL listed components since those items have been vetted for safety in your home.
The Danfoss BD50f compressor, for refridgeration, can operate in any power source, it requires 109 watts to operate. You need to purchase the Power Module for your voltage needs, 12/24v, 115v, or 220v. The Power Modules contain an inverter, transforming the input voltage to the requirements of the BD50f. If you have a 115v refridgerator with a BD50f compressor, you can swap Power Modules to the 12v version and run the refridgerator directly from batteries without an inverter. Therefore, more efficient battery usage.
@genetownsend8847
6 ай бұрын
That is good to know!
pro tip - never use a metal cart. plastic/resin carts are cheaper, won't ever rust, and avoids any issues with electrical devices
@fauxque5057
3 ай бұрын
Since you're the Pro, where would I buy a 3 shelf resin cart that can hold 12- LiPO4 batteries, and have the same dimensions of the steel cart? And for cheaper than the $54. I paid for mine at Harbor Freight. It's hen in service for 2 years with no shorts, and no rust yet. I also live in Florida with a high humidity rate and the cart is on the covered back porch. I do have some minimal surface rust starting on the vent covers on the MppSolar LV-6548 charge controllers. I probably should pop them off and shoot some Rustoleum on them this spring
@davebacknolaliki1452
2 ай бұрын
Pro tip put some insulating material between it and the components if you’re worried about it.
My setup I made in 2016 uses 4 6v 260Ah AGM batteries (Renogy) due to costs of lithium in 2018. A Renogy 2000w pure sine wave inverter/charger, cables, breakers, and fused properly. An Epever 40amp solar controller, MT50 monitor on an 800lb Gorilla cart. I can grid power, generator, or use the 800watts of solar panels. Tested and routinely used as UPS.
@Jasonoid
8 ай бұрын
Great setup! That's a lot of power right there!
I just installed a whole house 26kw NG generator with ATS and am interested in adding a whole house battery pack to sustain for 3-5 days. When batteries are exhausted generator starts, recharges and then shuts off. How do I determine my battery needs for whole house application?
when you showed the explosion with the resistor I lost it laughing LOL Too funny.
@Jasonoid
9 ай бұрын
Glad you enjoyed that haha
Great video and I love the cart idea! What would you say are the main advantages over this system vs a Delta Pro? I know what the retail price of the DP is but they routinely go on sale for close to this systems price.
@KeyBored101
Жыл бұрын
Will made a similar video and compared it to the DP Pro, I watched it this morning. kzread.info/dash/bejne/mJiZvNxtgdned5M.html
NICE!!!!
Older video I know, but... Could I tie two of these inverters together for split phase 240? I understand this can get complicated... Just wondering if this inverter can do that or if you have a suggestion on a different one to accomplish the goal of a similar cart build but that can provide 240 (split phase). Thanks for the video and simple break down.
There was no comment about the transfer switch wiring, normally they are wired for 240 split phase, but your invertor was 125V...I know the teansfer switch can be wirred as you want, but I did not hear that mentioned.
I really need to upgrade my system to LiFePO4 batteries. I've got a similar setup attached to 2 160W solar panels. Two 115A/h AGMs, a controller/regulator, and a 3000W Pure Sine wave inverter. I feel like it needs more battery capacity because I can lose 10% of my charge in an hour or two in full sun on the two parallel-connected batteries when running a computer, TV, stereo system, a 75 litre dual zone twin-lid camp fridge, a phone charger, and some LED strip lights. I'm wondering if I've set up an inefficient system. Both panels are connected in parallel as well. Maybe I'm expecting too much from the setup, I dunno. I can run the fridge by itself overnight after an hour or two of using the computer system setup, and it only drops to 48/50% . I need to rethink my computer setup though. It's a desktop using a 100cm Tv as a monitor, and a Sony stereo system for speakers. A lot of power just to watch KZread and catch up with news and social media. Good thing I have a ULP genset as a backup I guess.
Thanks for sharing the cart build, i think you have enough room on that shelf for 4 of those 200ah batteries so a 48v system coulda been done i think. i was a bit concerned seeing that battery not in a case, but then ya told us its because it wouldn't fit on the cart, still looks a bit weird but, it works.
@Jasonoid
Жыл бұрын
Even though the battery was removed from it's case the terminals were protected. One could fit 4 200ah batteries on the cart if two of them were removed from their cases, sad to see so much wasted space on these larger batteries! That's why I recommended the four (100ah) batteries in a series / parallel config so the battery warranties would be intact still. What I need to figure out is if a 48v server rack battery would fit on the shelf of this cart...haha
@user--PM
Жыл бұрын
i am sure you have watched some of will prowse's videos and that will give you an idea of how large those server rack batteries are. i would think that not gonna happen. a cart video of another creator i watch kzread.info/dash/bejne/fG2LvMWGdLTHdMo.html
@Jasonoid
Жыл бұрын
@@user--PM I watch both lithium solar and will prowse videos 👍 I love that cart video! Excellent design!
👍👍 good vid, thanks.
@Jasonoid
Жыл бұрын
Thanks for watching!
I've got the same system, except for the batteries. I have two 300 ah 12v power queen batteries. The same sungold 24 volt system. Will see how it works.
Seeing that you are going to a transfer switch, do you have the neutrals from invertor , line and load tied together. Bonding of neutral and ground at main line panel only. So your inverter should be a floating neutral , not bonded. The rule being bonding can only at one place only .
Oh, one more thing...I create insulated sleeves with heat shrink tubing. I tape off one end with electrical tape and then I slip one each over the pos and the neg lug. I use a tubing diameter that is snug enough that it will not fall off.
Don't solder your wires. It may seem like a good idea, but due thermal cycling, it can loosen. Best practice is to crimp.
Awesome!!
Can you add a wind generator with that system
Standing up the inverter will allow maximum cooling. If the fans on the bottom are sucking air in and the vents are on top, having the unit upright will keep the unit cooler via the chimney effect (heat rises).
@Jasonoid
Жыл бұрын
It actually pulls air in from the sides and shoots it out the bottom. The fans really move the air so I don't think it laying flat is an issue at all. The air coming out is always cool.
Hi, thanks for the video. Do the Power Queen batteries have low temp charging protection?
@Jasonoid
Жыл бұрын
The cheaper model doesn't, but in a house backup situation that shouldn't be an issue. It would take a bit for the house to get down below freezing. For another budget brand of battery that pulls full capacity, can be connected in series AND has low temp charging protection check out this battery: kzread.info/dash/bejne/lphluZqYpMfSYsY.html
It’s a floating neutral device, which is good because it will ground to your house via transfer switch. You don’t want 2 ground points at once
Is it possible to build this inside a big tool box? I just sold my small power station because i want something bigger for emergency or my job ( drywall construction) and building this on a tool box would be easier for me to carry
@Jasonoid
8 ай бұрын
Sure, you'd just want to make sure it has adequate ventilation since it has fans to keep cool.
@pilinke11
8 ай бұрын
@Jasonoid thanks for taking the time to answer!! I also saw a new power station dabbsson for a great price. I'm looking for a good 2000wh power station but I'm not sure if I should build my own because of all those bad reviews about costumer service also saw oukitel p2001 for $950
@Jasonoid
8 ай бұрын
@@pilinke11 I'm doing a really simple backup system video using a 12v 200ah battery and a 2000w inverter this week (should be out Friday). It's been running my fridge for 30 hours so far. DIY is nice since you can swap a part thag fails vs having an entire system go down. I have more confidence in the higher quality power stations but you have to pay a premium for them so DIY is a bit cheaper.
@pilinke11
8 ай бұрын
@Jasonoid I will wait for your video on Friday I need a backup but portability and the diy way is great in case something happens 😀
I bought a 20 amp plug in charger for my big 300ah battery and I used it with a 2000 watt inverter to power my microwave during a power outage. It was also nice to know I have multiple sources of power when the freezing storm with high winds hit n December, especially for my electric blanket. The wind chill was below zero and the power kept failing. Of course the new electric blankets are digital and so are the heaters I had here, so they don`t turn back on when the power goes out for a few minutes. So I plugged my electric blanket into one of my Bluetti EB70s. I accidentally put it on medium high instead of a lower setting when my foot hit the control switch but only used about half the battery during the night and of course it stayed on. I ran my WIFI and lights from batteries too. My 600 watt manual heater was at my sister`s house since it`s "too cheap" (I`m so dumb, see) so my nephew refused to bring it. I had to use the horrible and way overpriced digital job that`s 1500 watts and is either too hot or too cold and has to be turned on and off every few minutes and turns off when the power fails. It would drain my battery in a couple hours. So more and more I appreciate having these backup batteries and even have seven various low wattage cookers now that work with them. Six of my cookers work fine with my 500 watt power stations too, and two can be used with some of the smaller ones. I was born in the mid 1960s so these things are like miracles to me and I will never stop being amazed by this technology.
@Jasonoid
Жыл бұрын
Glad your backup batteries and inverter are working well for you! Have you built up any solar charging yet?
@baneverything5580
Жыл бұрын
@@Jasonoid No. I`m ordering another 190w HQST panel next month and the bolts to connect the 200 amp fuse to the inverter cable and some switches to be able to disconnect the panels and battery. After that I`m getting one more 100w panel to have four of those in series/parallel with the two 190w ones. Later I`ll either get two more larger panels or two 100w ones. I`d prefer the larger ones but the cost is higher. I need to get two 100w mono panels. My others are poly but the 190w ones will both be mono. The good thing is in a pinch I can dump power into the large battery with my two EB70s and my two 500 watt power stations with the 20 amp plug in charger. I need to learn how to do this with their 12v ports but they only produce about 100 watts. I`m thinking of getting some cheap MPPT charge controllers to rig up for this. Not sure how to go about it yet though. It would be nice to have that option if needed. I can dump over 1500 kwh into it that way to extend run time. But I also want to be able to get the big battery back up from a very low state of charge at night or on a cloudy day if I happen to drain it too low. I think the higher priced Renogy 500 amp battery meter will prevent that. There`s a less expensive one but it may be more difficult to use and may not be worth the 20 bucks less. I want an accurate meter to avoid surprises.
Hi Can you charge from ac and same time use transfer switch like UPS for your fridge or pc , great video thanks
@Jasonoid
Жыл бұрын
Yes, this supports UPS functionality
do you know of any software for the communication that will work for this inverter. i built the same sort of setup
you can only power one side with your transfer switch correct. I go with a 2 phase inverter.
@Jasonoid
9 ай бұрын
correct, 120v with this setup.
Question so the power coming out of your inverter is only supplying 120 volts to you transfer switch am I right. If not how did you wire the the connection in the transfer switch box. Why didn't you ground the output from the inverter. Thanks
did you used converter from 24v to 12v for some appliances or devices 12v?
@Jasonoid
8 ай бұрын
You can definitely do that if you are wanting to run 12v devices off the 24v battery. There are many options available online.
@DahStratMode3
8 ай бұрын
@@Jasonoid are there any harm when you use the 12v device or appliance on 24v system with no converter?
@Jasonoid
8 ай бұрын
Yes, the 12v device will be harmed or damaged with the higher voltage. Don't hook 12v devices up to 24v batteries.
💘💘💘💘💘💘. Love your presentation. Thanks
Tear downs are good. You really do need to see the quality of the build.
Always check your regulations. Where I live they won't even allow a 1000w system in your home. That's just a single 12v 100ah battery! I can however stick it in the detached cold garage....
Another great video, I would like to continue building on my portable setup i e. "Kisae DC to DC charger setup". Can you suggest a Pure Sine Wave Inverter to go with my portable setup? In addition since this would be my first time setting up an inverter. Would that Resistor in this video really suppress any sparks that could occur? I have the DC HUB already as part of my portable setup. I would like to have a little AC power if I happen to need it in an emergency. Any help would be greatly appreciated.
@Jasonoid
8 ай бұрын
You'll see a spark on large inverter over 2000 watts, theres so LARGE capacitors that will want to charge quickly. What size inverter are you looking for your setup?
@minceym
8 ай бұрын
@@Jasonoid 1000 Watt inverter and put it in a water proof case. So I'll have to set it up every time I want to use it. That's why I'm concerned about sparks. You are the first person I saw on KZread that addressed this issue. Please inform. Thanks Again!
@Jasonoid
8 ай бұрын
@@minceym you won't have an issue with sparks on a 1000w inverter, the capacitors aren't big enough. I really like Bestek inverters. I have their 500w and 350w models, it looks like they also sell a 1000w pure sine wave model too: amzn.to/44j5MkA
@minceym
8 ай бұрын
@@Jasonoid This is great! Thank you very much for this information. I never saw a portable inverter like that before. So is it safe to say anything over a 1000 watts the resistor would work?
@Jasonoid
8 ай бұрын
@@minceym yeah
Thanks!
@Jasonoid
Жыл бұрын
Thank you so much Erik!
What is the durability of this set up? How often would you need to replace things like the batterys and inverter? I mostly want something like this that i can use as a power source during emergencies so i don't have to run my generator all day and night.
The only thing I would change with this system is placing the battery fuse closer to the battery and adding a battery disconnect for safety
Great video Jason, I'm thinking on two of the 12.8v 200 amp batteries. What would you say?
@Jasonoid
7 ай бұрын
Those will work well in series for a 24v inverter!
great video thanks. Is the AC charging input variable ? Can you adjust it to charge from a 1000w external generator?
@Jasonoid
3 ай бұрын
Yes, you can change the charge rate in the setting of the All In One unit to what you want.
@cargenerator
3 ай бұрын
@@Jasonoid thanks. So if you need more power during an outage even without sun or solar, you could use your Car as a Generator to refill at say 800-1000 watts with our product CarGenerator. Its a turn-key user friendly inverter in a fully weatherproof housing, you can just run an extension cord in from your car and let it charge for a few hours to refill. Let us know if you would like to have a demo unit to review etc. Here is a rainy example... kzread.info/dash/bejne/rJhlypN8lLLfk6Q.html